User manual (AEH2900, AEH2110, AEH2120, AEH2130, AEH2310)
Contents 1 Important safety instructions 3 3 Safety Important Safety Instructions 3 Compliance 4 Care of the environment 5 Notice 5 Written Offer 6 2 Overview 7 Motion sensor 7 Door and window sensor 7 Temperature and humidity sensor 8 Intelligent switch 9 Status indicator 9 3 Setup 11 Join your Smart Home network 11 Install or replace batteries 12 Plug the Intelligent switch 14 Reset 15 Reset network connection 15 Restore factory settings 16 4 Place 18 EN 1
Place the Motion sensor 18 Find a right location 18 Use the mounting kit 18 Use the adhesive tape 19 Place the Door and window sensor 5 Use 20 23 Philips Smart Home app 23 Manage devices 24 Set the device 24 Check device status 24 Delete the device 25 Set the rules of home automation 26 Set the trigger 26 Set the action 26 Edit the rules 27 Access the devices remotely 28 6 Check for updates 29 7 Technical data 30 Sensors (for indoor use only) 30 Door and window sensor 3
1 Important safety instructions Safety CAUTION: For INDOOR USE ONLY! DO NOT use this Intelligent switch with non-resistive loads, such as motors, compact fluorescent light (CFL) bulbs or fluorescent lighting.To reduce the risk of electric shock, this Intelligent switch has a third (grounding) pin. As a grounding type plug, this Intelligent switch only fits into a grounding type power outlet.
Compliance Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Notice for the USA This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Care of the environment Environmental information All unnecessary packaging has been omitted. We have tried to make the packaging easy to separate into three materials: cardboard (box), polystyrene foam (buffer) and polyethylene (bags, protective foam sheet.) Your system consists of materials which can be recycled and reused if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packaging materials, and old equipment.
• The sensors and/or Intelligent switch are intended as an aid. They are not substitutes for home security supervision and should not be used as such. Written Offer Gibson Innovations hereby offers to deliver, upon request, a copy of the complete corresponding source code for the copyrighted open source software packages used in this product for which such offer is requested by the respective licenses. This offer is valid up to three years after product purchase.
2 Overview With the Smart Home devices and Philips Smart Home app, you can have the changes at your home monitored, and set rules to have the connected home appliance powered on or off automatically according to the changes. Motion sensor The Motion sensor detects the movement of people at home. a b AEH2110 a Status indicator b Detection lens Door and window sensor The Door and window sensor detects the opening/closing of door or window at home.
a b AEH2120 a Status indicator b Alignment mark Temperature and humidity sensor The Temperature and humidity sensor detects the temperature and humidity at home.
Intelligent switch The Intelligent switch powers on or off the connected appliance at home.
Solid green for less than one second Flashing red Flashing red and green alternately Low battery Solid red for three seconds, and then, flashing red 10 EN An event that triggers notifications happens.
3 Setup Join your Smart Home network 1 On your mobile device, download and install the Philips Smart Home app. Philips Smart Home + Smart Home Get started Smart Home Demo iOS 2 3 Follow the onscreen instructions to get connected to the Bridge. Follow the onscreen instructions to add your Smart Home devices to the Bridge. For setup, bring the Smart Home device as close to the Bridge as possible. a Install the batteries. Push to close the battery door.
1 2 2 3 All devices No device has connected Add devices Search Home Rules Settings Note •• The device exits the pairing mode after three minutes. To re-enter the pairing mode, open the battery door and close it as described in Step 3.
Motion sensor 1 3 2 Door and window sensor 1 3 2 Temperature and humidity sensor 1 2 3 EN 13
Plug the Intelligent switch To add the Intelligent switch to the Bridge, do the following: 1 2 14 Insert the Intelligent switch into a power outlet properly. Press and hold the Setup button until the status indicator turns from amber to red.
Reset Reset network connection Reset the network connection when: • a device re-joins the Smart Home network after the batteries are replaced. • there are connection problems with the Smart Home network. Indicator flashing red Status of the device Network connection lost On the sensor, do the following: 1 2 Open the battery door. Push to close the battery door. Release the door when the status indicator flashes in amber.
2 With the Philips Smart Home app, add the device to the Bridge (see 'Join your Smart Home network' on page 11). Restore factory settings Restore factory settings when: • you want to connect your device to another Bridge. On the sensor, do the following: 1 2 3 Delete the device from the Bridge (see 'Delete the device' on page 25). Open the battery door. Push to close the battery door. Don't release the door until the status indicator turns from amber to red.
Tip •• If you press and hold the setup button for more than six seconds, the status indicator turns off. To restore factory settings, re-do Step 1.
4 • • • Place Use the Smart Home devices in an indoor environment. Keep such devices from exposure to moisture, direct sunlight, or excessive heat. To ensure good connection, check the distance and obstacles, such as walls, between the Bridge and devices. Place the Motion sensor Find a right location • • • Select a location where a person is expected to cross the range of detection.
>30mm 5mm 1 2 b a 3 • 4 In Step 2, use the screw holder for a concrete wall or surface. For a wooden surface, you can the screw only. Use the adhesive tape You can also use the adhesive tape mount the sensor as needed.
2 1 3 Place the Door and window sensor • • • Avoid the exposure to moisture and direct sunlight. Use the alignment marks to align the two components. Mount the two components securely just in case any one of them may drop during movement.
1 EN 21
2 22 EN
5 Use Philips Smart Home app Through the Philips Smart Home app you can set up the Smart Home devices, set rules of home automation, and continue to monitor changes and control the devices on a mobile device while you are away from home. c b d e a f g a Go to the Home screen. b Find connected devices by type or location. c Display connected devices in a view of grid or list. d Set the device. e Add a device. f Go to the settings menu. g Set or edit the rules of home automation.
Manage devices Set the device You can edit the device information by attaching a photo and naming the location. • On the Home screen, tap the device to edit the device information. • For the Motion sensor, select the sensitivity level as needed. • You can select the unit of measurement for the Temperature and humidity sensor, Fahrenheit degree or Celsius degree. From the Home screen, tap > Unit. Check device status Go to the Home screen to check the status of devices.
Delete the device Delete the device when: • you want to remove the device from the Bridge. • you want to restore the factory settings of the device. (see 'Restore factory settings' on page 16) 1 2 From the Home Screen, select the device. Tap the option to delete the device.
Set the rules of home automation To set a rule of home automation, set an event or time/ location as trigger. Then, set an action that is associated with the trigger. Set the trigger 1 2 From the Home screen, go to . Tap to create a rule. Tap a icon to set a trigger. • A trigger can be an event detected by your Smart Home device, or time or location detected by your mobile device. • To set a location as trigger, you can also go to and select Geofencing.
Edit the rules • From the Home screen, tap . Select a rule to edit or delete it.
Access the devices remotely To access your Smart Home devices remotely, log in to the portal. The first time you log in to the portal, create your account.
6 Check for updates For updates of your Smart Home devices and the Philips Smart Home app, you can receive messages on your mobile device. Follow the onscreen instructions to complete the updating.
7 Technical data Sensors (for indoor use only) Power • Two AAA alkaline batteries Connectivity • Zigbee Motion sensor Detection method • Passive Infra red Door and window sensor Operating temperature & humidity • 32°F to 104°F (0°C to 40°C), 10% to 90% Temperature and humidity sensor Operating temperature & humidity • Temperature: 32°F to 104°F (0°C to 40°C) • Humidity: 10% to 95% Intelligent switch Grounding type power plug (for indoor use only) • Model: AEH2310/37 Output: AC 120 V~ 60 Hz, 15 A, 1800
EN 31
2015 © Gibson Innovations Limited. All rights reserved. This product has been manufactured by, and is sold under the responsibility of Gibson Innovations Ltd., and Gibson Innovations Ltd. is the warrantor in relation to this product. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license from Koninklijke Philips N.V. AEH2900_37_UM_V1.