Register your product and get support at www.philips.
Important notes for users in U.K. Mains plug This apparatus is fitted with an approved moulded plug. Should it become necessary to replace the main fuse, this must be replaced with a fuse of same value as indicated on the plug (example 10A). 1. Remove fuse cover and fuse. 2. The replacement fuse must comply with BS1362 and have the A.S.T.A. approval mark. If the fuse is lost, contact your dealer in order to verify the correct type. 3. Refit the fuse cover.
English 1 Important Safety and important notice Warning • Risk of overheating! Never install the product in a confined space. Always leave a space of at least 4 • • • • • • inches around the product for ventilation. Ensure curtains or other objects never cover the ventilation slots on the product. Never place the product, remote control or batteries near naked flames or other heat sources, including direct sunlight. Only use this product indoors.
Your product contains batteries covered by the European Directive 2006/66/EC, which cannot be disposed with normal household waste. Please inform yourself about the local rules on separate collection of batteries because correct disposal helps to prevent negative consequences for the environmental and human health. Copyright notice This product incorporates copyright protection technology that is protected by method claims of certain U.S.
‘Blu-ray Disc’ and ‘Blu-ray Disc’ logo are trademarks. Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories. Manufactured under license under U.S. Patent # s: 5,451,942; 5,956,674; 5,974,380;5,978,762; 6,487,535 & other U.S. and worldwide patents issued & pending. DTS and DTS 2.0+Digital Out are registered trademarks and the DTS logos, Symbol are trademarks of DTS, Inc. ©1996-2008 DTS, Inc. All Rights Reserved.
2 Your product Congratulations on your purchase, and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/welcome. Feature highlights Philips EasyLink Your product supports Philips EasyLink, which uses the HDMI CEC (Consumer Electronics Control) protocol. EasyLink-compliant devices that are connected through HDMI connectors can be controlled by a single remote control.
Region code DVD Country BD B Product overview Main unit a • Turn on this product or switch to standby mode. b Disc compartment c IR sensor • Point the remote control at the IR sensor. d Display panel e • Open or close the disc compartment. • Start or resume play. • Pause play.
Front panel display Description LOADING Loading a disc. UNSUPP The disc is not supported. BD Blu-ray disc is recognized. HDMI ERR The HDMI video resolution is not supported by TV. FASTFWD Fast forward mode. FASTBWD Fast reverse mode. SLOWFWD Slow forward mode. SETTINGS Setup menu is displayed. HOME Home menu is displayed. CHAPTER Current chapter is in chapter repeat mode. DOLBY D Dolby Digital audio is being played. DOLBY HD Dolby HD audio is being played.
Remote control a • • Turn on this product or switch to standby mode. When EasyLink is enabled, press and hold for at least three seconds to turn all connected HDMI CEC compliant devices to standby. b BONUSVIEW • Turn on or off the secondary video in a small screen window during play (applicable only to BD-video that supports the BONUSVIEW or Picture-In-Picture feature). c TOP MENU • BD: Display the top menu. • DVD: Display the title menu. d • e Access the home menu.
f OK • Confirm an entry or selection. g • Navigate through the menus. h BACK Return to a previous display menu. • i / • j Skip to the previous or next title, chapter, or track. / • Search backward or forward. k • Mute volume (applicable only to certain Philips brand TVs). • +/Adjust volume (applicable only to certain Philips brand TVs). l m SUBTITLE • Select a subtitle language on a disc. n AUDIO • Select an audio language or channel on a disc.
• 3 Select repeat play or random play. Connect Make the following connections to use this product. Basic connections: • Video • Audio • Power Optional connections: • Route audio to other devices • Digital amplifier/receiver • Analog stereo system • USB device (As additional memory for software updates and BonusView contents. NOT for media play) Note • Refer to the type plate at the back or bottom of the product for identification and supply ratings.
Option 1: Connect to the HDMI jack USB HDMI IN 1 Connect an HDMI cable (not supplied) to • the HDMI jack on this product. • the HDMI input jack on the TV. Tip • If the TV has a DVI connector only, connect via an HDMI/DVI adaptor. Connect an audio cable for sound output. • You can optimize the video output. Press HDMI repeatedly to select the best resolution the TV can support. • Philips recommends HDMI category 2 cable, also known as High Speed HDMI cable, for optimal video and audio output.
• the AUDIO input jacks on the TV. Tip • The video input jack on the TV might be labeled as A/V IN, VIDEO IN, COMPOSITE or BASEBAND. • This type of connection provides standard picture quality. Route audio to other devices To enhance audio play, you can route the audio from this product to other devices. Connect to digital amplifier/receiver COAXIAL USB 1 Connect a coaxial cable (not supplied) to: • the COAXIAL jack on this product. • the COAXIAL/DIGITAL input jack on the device.
Note • This product cannot play any audio/video/photo file stored on a USB device. • Connect a USB device only to the USB jack on this product. • Philips does not guarantee 100% compatibility with all USB devices. 1 Connect the USB device to the USB jack on the back of this product. Connect power Caution • Risk of product damage! Ensure that the power supply voltage corresponds to the voltage printed on the back of the unit.
1 2 3 Open the battery compartment. Insert 2 AAA batteries with correct polarity (+/-) as indicated. Close the battery compartment. Note • If you are not going to use the remote control for a long time, remove the batteries. • Do not use old and new or different types of batteries in combination. • Batteries contain chemical substances, so they should be disposed of properly. Find the correct viewing channel 1 2 Press to turn on this product.
Button Action Move up or down. Move left or right. OK Confirm a selection. Enter numbers. Select menu display language Note • If this product is connected to a HDMI CEC compliant TV, skip this setting. It switches automatically to the same OSD menu language as per your TV setting (if the language set on TV is supported by this product). 1 2 3 In the Home menu, select [Settings] and press OK. Select [Preference Setup], then press . Select [Menu Language], then press .
Note • To enable the EasyLink feature, you must turn on the HDMI CEC operations on the TV and on other devices connected to TV. Refer to the TVs/devices manual for details. One-touch play 1 Press the STANDBY button to turn on this product. » The TV (if supports one-touch play) automatically turns on and switches to the correct video-in channel. » If a disc is loaded in this product, disc play automatically starts.
Note • Check disc/file formats supported (see “Your product” > “Playable media”). • If the password entry menu is displayed, enter the password before you can play the locked or restricted disc (see “Adjust settings” > “Preference Setup” > [Parental Control]). • If you pause or stop a disc, the screen saver appears after 10 minutes of inactivity. To deactivate the screen saver, press any button.
Button Action AUDIO Select an audio language or channel on a disc. SUBTITLE Select the subtitle language on a disc. REPEAT Select or turn off repeat or shuffle mode. • Repeat options may vary from the disc type. • For VCDs, repeat play is only possible when the PBC mode is turned off. INFO Display the current status or disc information. OPTIONS Access options relating to the current activity or selection.
Select title/chapter 1 During play, press OPTIONS. » The play options menu is displayed. 2 3 Select [Title] or [Chapter] in the menu, then press OK. Select the title or chapter number, then press OK. Skip play to a specific time 1 During play, press OPTIONS. » The play options menu is displayed. 2 3 Select [Time Search] in the menu, then press OK. Press the Navigation buttons ( ) to change the time to skip to, then press OK. Zoom in/out 1 During play, press OPTIONS.
Note • Applicable only to discs that contain multi-angle scenes. Shift subtitle display This feature is only available if you have set the [TV Display] to [Cinema 21:9] (see “Adjust settings” > “Video Setup”). 1 During play, press OPTIONS. » The play options menu is displayed. 2 3 Select [Shift Subtitle] in the menu, then press . Press the Navigation buttons ( ) to shift the subtitle, then press OK. Tip • You can press SUBTITLE on the remote control to access Shift Subtitle feature.
1 2 B Secondary video Press BONUSVIEW to turn on the secondary video window. Press OPTIONS. » The play options menu is displayed. 3 4 Select [2nd Audio Language] or [2nd Subtitle Language] in the menu, then press Select the language to play, then press OK. . Play DivX® video DivX video is a digital media format that retains high quality despite a high rate of compression. You can enjoy DivX video on this DivX certified product. 1 Insert a disc that contains the DivX videos.
Button Action Pause play. Start or resume play. Stop play. Skip to a previous/next track. / Select an item to play. Search fast-backward or fast-forward. Press repeatedly to change the search speed. / REPEAT Select or turn off repeat or shuffle mode. Play MP3/WMA music MP3/WMA is a type of highly compressed audio file (files with .mp3, .wma extensions). 1 Insert a disc that contains the MP3/WMA music. 2 Press , select [Play Disc], then press OK. » A contents menu is displayed.
3 Select a photo folder, then press OK to enter. • To select a photo, press the Navigation buttons. • To enlarge the selected photo and start slideshow, press OK. Press OK to start slideshow play. 4 Note • It may require longer time to display the disc content on the TV due to the large number of songs/ photos compiled onto one disc. • This product can only display digital camera pictures according to the JPEG-EXIF format, typically used by almost all digital cameras.
Note • To create a musical slideshow, you must store the MP3/WMA and JPEG files on the same disc. 1 2 3 6 Play MP3/WMA music. Press BACK to return to the main menu. Navigate to enter a photo folder, then press OK to start slideshow play. » Slideshow begins and continues till the end of the photo folder. » Audio continues to play until the end of the disc. • To stop the slideshow play, press . • To stop the music play, press again.
Select a language for disc menu. Note • If the language you have set is not available on the disc, the disc uses its own default language. • For some discs, the subtitle/audio language can only be changed from the disc menu. [TV Display] Select a display format: • • • • • [4:3 Letterbox] – For 4:3 screen TV: wide-screen display with black bars on the top and bottom of the screen. [4:3 Panscan] – For 4:3 screen TV: full-height display with the trimmed sides.
This feature is available only when the display device is connected by a HDMI cable, and when it supports deep color feature. • [Auto] - Enjoy vivid images in over a billion colors on Deep Color enabled TV. • [Off] - Output standard 8 bit color. [Picture Settings] Select a predefined set of picture color settings. • [Standard] – Original color setting. • [Vivid] – Vibrant color setting. • [Cool] - Soft color setting. • [Action] – Sharp color setting. It enhances the details in the dark area.
• • [Bitstream] – Select the best original HD audio experience (only via an HD audio compatible receiver). [Auto] – Detect and select the best supported audio format automatically. [Digital Audio] Select an audio format for the sound output from the DIGITAL OUT jack (coaxial/optical). • [Auto] - Detect and select the best supported audio format automatically. • [PCM] - The audio device does not support multi-channel format. Audio is downmixed to two-channel sound.
Note • If this product is connected to an HDMI CEC compliant TV using a HDMI cable, it switches automatically to the same menu display language as per your TV setting (if the language set on TV is supported by this product). [Parental Control] Restrict access to discs that are unsuitable for children. These types of discs must be recorded with ratings. To access, enter your last set password or ‘0000’. Note • Rated discs above the level you set in [Parental Control] require a password to be played.
EasyLink Setup 1 2 3 Press . Select [Settings], then press OK. Select [EasyLink Setup], then press . Video Setup Audio Setup EasyLink On One Touch Play On One Touch Standby On Preference Setup EasyLink Setup Advanced Setup 4 5 Select an option, then press OK. Select a setting, then press OK. • To return to the previous menu, press • To exit the menu, press . BACK.
[EasyLink] This product supports Philips Easylink which uses the HDMI CEC (Consumer Electronics Control) protocol. You can use one single remote control to control all EasyLink-compliant devices that are connected through HDMI connectors. • [On] - Turn on EasyLink features. • [Off] - Disable EasyLink features. [One Touch Play] When you press the STANDBY button to turn on this product, the TV (if the TV supports onetouch play) automatically turns on and switches to the video-in channel.
• [USB] - Download software from the USB device which is connected to this product. Note • For detailed software updating, see “Additional information” > “Update software”. [Clear Memory] Remove some Blu-ray disc data (such as BonusView) that are automatically copied on the connected USB device. Tip • On the connected USB device, a folder named “BUDA” is automatically created to store some necessary data from Blu-ray disc. [DivX® VOD Code] Display the DivX® registration code.
Update software via USB 1 2 3 4 5 6 Go to www.philips.com/support to check if the latest software version is available for this product. Download the software onto a USB flash drive. Insert the USB flash drive to the USB jack of the rear panel. In the Home menu, select [Settings] > [Advanced Setup] > [Software Download] > [USB]. Follow the instructions on the TV screen to confirm update operation. » Once software update is complete, this product automatically turns off to standby.
• • Sampling frequency: • MP3: 32 kHz, 44.1 kHz, 48 kHz • WMA: 44.1 kHz, 48 kHz Constant bit rate: • MP3: 112 kbps - 320 kpbs • WMA: 48 kpbs - 192 kpbs USB • As additional memory for software updates and BonusView contents. Not for media play. Main unit • Power supply rating • Europe: 220~240V ~AC, ~50 Hz • Power consumption: 25W • Power consumption in standby mode: < 1 W • Dimensions (w x h x d): 360 x 54 x 240 (mm) • Net Weight: 2.
Model No. __________________________ Serial No. ___________________________ Main unit No reaction to the remote control. • Connect this product to the power outlet. • Point the remote control at the IR sensor located on the front panel of this product. • Insert the batteries correctly. • Insert new batteries in the remote control. Picture No picture. • See TV manual for correct video input channel selection. Change the TV channel until you see the Philips screen. No picture on HDMI connection.
• • • Ensure that this product supports the region code of the DVD or BD. For DVD±RW or DVD±R, ensure that the disc is finalized. Clean the disc. Data files (JPEG, MP3, WMA) cannot be played or read. • Ensure that the data file was recorded in the UDF, ISO9660 or JOLIET format. • Ensure that the selected group (folder) does not contain more than 9,999 files for DVD, and 999 files for CD. • Ensure that the JPEG file extension is.jpg, .JPG, .jpeg or .JPEG. • Ensure that the MP3/WMA file extension is .mp3 or .
D Digital Audio Digital Audio is a sound signal that has been converted into numerical values. Digital sound can be transmitted through multiple channels. Analogue sound can only be transmitted through two channels. DivX Video-On-Demand This DivX Certified ® device must be registered in order to play DivX Video-on-Demand (VOD) content. To generate the registration code, locate the DivX VOD section in your device setup menu. Go to vod.divx.
P PBC Playback Control. A system where you navigate through a Video CD/Super VCD with on-screen menus that are recorded onto the disc. You can enjoy interactive playback and search. PCM Pulse Code Modulation. A digital audio encoding system. R Region code A system that allows discs to be played only in the region designated. This unit only plays discs that have compatible region codes. You can find the region code of your unit on the product label.
Open Source Software This product contains the following open source software packages, which are subject to their respective licenses. 1. Zlib general purpose compression library See http://www.zlib.net/, and in particular http://www.zlib.net/zlib_license.html. /* zlib.h -- interface of the ‘zlib’ general purpose compression library version 1.2.3, July 18th, 2005 Copyright (C) 1995-2005 Jean-loup Gailly and Mark Adler This software is provided ‘as-is’, without any express or implied warranty.
THE FREETYPE PROJECT IS PROVIDED `AS IS’ WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT WILL ANY OF THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY DAMAGES CAUSED BY THE USE OR THE INABILITY TO USE, OF THE FREETYPE PROJECT. 2.
openssl-core@openssl.org. OpenSSL License Copyright (c) 1998-2008 The OpenSSL Project. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2.
Original SSLeay License Copyright (C) 1995-1998 Eric Young (eay@cryptsoft.com). All rights reserved. This package is an SSL implementation written by Eric Young (eay@cryptsoft.com). The implementation was written so as to conform with Netscapes SSL. This library is free for commercial and non-commercial use as long as the following conditions are aheared to. The following conditions apply to all code found in this distribution, be it the RC4, RSA, lhash, DES, etc., code; not just the SSL code.
The licence and distribution terms for any publically available version or derivative of this code cannot be changed. i.e. this code cannot simply be copied and put under another distribution licence [including the GNU Public Licence.] NOTICE SOFTWARE END USER LICENSE AGREEMENT THIS SOFTWARE END USER LICENSE AGREEMENT (“THIS AGREEMENT”) IS A LEGAL AND BINDING AGREEMENT BETWEEN YOU (EITHER AN INDIVIDUAL OR ENTITY) AND PHILIPS CONSUMER ELECTRONICS B.V.
3. License Restrictions. Except as provided otherwise herein, you shall not rent, lease, sublicense, sell, assign, loan, or otherwise transfer the Software. You shall not, and you shall not permit any third party, to reverse engineer, decompile, or disassemble the Software, except to the extent that applicable law expressly prohibits the foregoing restriction. You may not remove or destroy any product identification, copyright notices, or other proprietary markings or restrictions from the Software.
5. Open Source Software. Your license rights do not include any right or license to use, distribute or create derivative works of the Software in any manner that would subject the Software to Open Source Terms.
11. LIMITATION OF LIABILITY. UNDER NO CIRCUMSTANCES WILL PHILIPS OR ITS LICENSORS BE LIABLE FOR ANY CONSEQUENTIAL, SPECIAL, INDIRECT, INCIDENTAL OR PUNITIVE DAMAGES WHATSOEVER, INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS OR REVENUES, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, LOSS OF DATA, LOSS OF USE OR OTHER PECUNIARY LOSS, EVEN IF PHILIPS OR ITS LICENSORS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
© 2009 Koninklijke Philips Electronics N.V. All rights reserved. BDP2500_12_05_UM_V2.
