Quick start guide CD180
Important safety instructions • • • • Use only the power adapter listed in the technical data. Do not allow the product to come into contact with liquids. Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. (Refer to the user manual online) Overview Earpiece Microphone • Find handsets. • Register additional handsets.
In call In idle mode Enter the option menu menu REDIAL/C Enter the redial list Enter the redial list Increase the volume Enter the phonebook Decrease the Enter the call log volume Make and receive calls End calls Turn handset on/off (press and hold) Mute/unmute the microphone R Recall key* *network dependent MENU/OK Enter the option In menu Confirm selection Cancel operation Scroll up Scroll down Exit menu/operation
It displays the connection between the handset and the base. The more the bars are shown, the better the connection is. It indicates a received call in the call log. It indicates an outgoing call in the redial list. It flashes when there is a new missed call. It remains steadily on when browsing the missed calls in call log. It flashes when receiving incoming call. It remains steadily on during a call. The ringer is off.
1 Connect Connect the base station Telephone socket Power socket 1 Connect each end of the power adapter to: Power socket Power adapter Telephone base station 2 1 3 Extra handset charger • the DC input jack at the bottom of the base station; • the power socket on the wall. 2 Connect each end of the line cord to: • the telephone socket at the bottom of the base station; • the telephone socket on the wall.
2 Get started Configure your phone 1 The batteries are pre-installed in the handset. Pull the battery tape off from the battery door before charging. 2 When using your phone for the first time, you see a welcome message (country dependent). After the welcome message, press MENU/OK. 3 Please set the country and language if prompted. 4 Set the date and time. • If the time is in 12-hour format, press / key to select [AM] or [PM].
Charge your phone Place the handset on the base station to charge the handset. When the handset is placed correctly on the base station, you hear a docking sound. »» The handset starts charging. Note Charge the batteries for 8 hours before first use. Check the battery level Charge 8 hours When the handset is off the base station/charger, the bars indicate the battery level (full, medium and low). When the handset is on the base station/charger, the bars flash until charging completes.
3 Enjoy Call • To make a call, press and dial the phone number. • To answer a call, press when the phone rings. • To end a call, press . Earpiece volume Press or to adjust the volume during a call. Phonebook Add record 1 Press MENU/OK, then select [PHONEBOOK] > [ADD NEW], then press MENU/OK to confirm. 2 Enter the name, then press MENU/OK to confirm. 3 Enter the number, then press MENU/OK to confirm.
Call log Redial list To make a call To make a call To view more details To save a call record to the phonebook 1 Press 2 Press and select a record. . 2 Press MENU/OK. 3 Select [VIEW]. To save a call record to the phonebook 2 3 4 5 6 7 Press MENU/OK. Select [Save number]. Press MENU/OK to confirm. Enter the name. Press MENU/OK to confirm. Press MENU/OK to save. To delete a call record 2 Press MENU/OK. 3 Select [Delete] or [Delete all]. 4 Press MENU/OK to confirm.
Restore default settings You can reset your phone settings to the original factory settings. 1 Press MENU/OK. 2 Select [SERVICES] > [Reset], then press MENU/OK to confirm. »» The handset displays a confirmation request. 3 Press MENU/OK to confirm. »» All settings are reset »» The welcome screen displays. Technical data Battery • CORUN: 2 x AAA NiMH 1.2V Rechargeable 500mAh batteries • SANIK: 2 x AAA NiMH 1.
Frequently asked questions No signal bar displays on the screen. • The handset is out of range. Move it closer to the base station. • If the handset displays [Unregistered], register your handset (See the section on Register the handsets). If I fail to register the additional handsets to the base station, what do I do? Your base memory is full. Unregister the unused handsets and try again. No dialing tone • Check your phone connections. • The handset is out of range.
Welcome to Philips Register your product at www.philips.com/welcome Need help? User manual / Online help www.philips.com/support When this crossed-out wheeled bin symbol is attached to a product it means that the product is covered by the European Directive 2002/96/EC. Reproduction in whole or in part is prohibited without the written consent of the copyright owner. Trademarks are the property of Koninklijke Philips Electronics N.V. or their respective owners. © 2013 Koninklijke Philips Electronics N.V.