Philips Hospitality TV Installation Manual for 22HFL3233D/10 26HFL3233D/10 32HFL3233D/10 42HFL3233D/10 Version 1.
Contents 1. Requirements before starting the installation.......................................................................................................... 2 2. Find out the state of the TV ...................................................................................................................................... 3 3. Re-install TV ...........................................................................................................................................................
1. Requirements before starting the installation Before starting the installation, make sure that you have everything you need at hand. Master remote control 22AV8573 or Guest remote control 22AV1104B And USB stick You will need the master remote control or the guest remote control to access the menus. To access the setup menu press the ‘RC5 SETUP’ key, and then press the ‘Home/Menu’ button. For the guest remote control, press the following keys sequential: 3,1,9,7,5,3, ‘MUTE’.
2. Find out the state of the TV It is important to know if a TV is in ‘virgin mode’ (out of the box) or installed before. If you can see this screen below, you know that the TV is in ‘virgin mode’ and you can install the set. See chapter 4 of this manual. If you power on the set and then press the ‘Home’ button on the guest remote, you will see this screen appear, if the TV already has been installed or the wizard was already skipped.
3. Re-install TV If you want to start an installation from scratch you can always re-install the TV. This can be done by using the option: Re-install TV set. If PBS is active you can access the setup menu press the ‘RC5 SETUP’ key, and then press the ‘Home/Menu’ button (For the guest remote control, press the following keys in sequence: 3,1,9,7,5,3, ‘MUTE’) , then go to Consumer Setup, confirm with “OK”.
Navigate to “Reinstall TV” Press “OK” to reinstall TV set. If all is correct select “YES” and press “OK”. After this operation the TV will power off and on and display the installation wizard. Note: All settings are at default values and no channel plan is available. After reinstalling, the PBS Setup menu will keep the PBS Mode, Room ID and PBS Setup menu and reset all other parameters to default values.
4. Installation wizard. When you turn on the TV for the first time, or you have reinstalled the TV, you should see the following screen. Here you will need to select your preferred language. After this, you will need to select the country. Depending on the country selection, some pre-defined settings will be activated. Note: If you are experiencing some issues after selecting your country, please select ‘Others’ in the menu. The next step is to select ‘Wall mounted’ or ‘On a TV stand’.
The next step is to choose between ‘Shop’ and Home’ use. If you select “SHOP” an ‘e-sticker’ banner will be displayed on the TV. This is for commercial purpose only. Now you can select the visual and hearing impaired options. If you select ‘On’, your TV will automatically turn on settings to help visual and hearing impaired people. THE MOST COMMON OPTION IS TO TURN THIS FUNCTION OFF. On the following page we can start the channel installation wizard.
For the channel installations, select ‘Install TV channels’ and press ‘OK’ Then you can select ‘Continue’ and press ‘OK’ again. Here you can select the type of channels you would like to install. 1. Antenna (DVB-T) + analogue channels 2. Cable (DVB-C)+ analogue channels Note: The installation wizard is identical for DVB-T and DVB-C. Note: The analogue channels can be skipped in a future step.
It is advisable to check the settings before starting the search. The first option in the settings page is the “Frequency scan”. This has 2 options: - “Quick”: this is a fast method to search channels but it might skip some channels (depending on the network). - “Full”: the scan will search on all frequencies and will store all channels available. This is the safe method if you don’t know the network parameters, but it takes the longest time. The second option in the settings page is “Analogue Channel”.
The last option is “Reset” and this will reset the search settings to default. After you have checked or changed settings, you can select “Done” and select “Start” to start the channel search. During the channel search you can see the progress bar and how many channels are found at that time. When the search is done, you should see “Channel search complete” and a summary of the channels found.
A wizard will start to guide you through the process of setting the sound and picture on the TV set. Select “Continue” to start the wizard and press “OK” on remote control. The wizard will ask you some questions about which image you prefer, select the option you desire and press “OK” on the remote control. Once this wizard is done, you will return to the installation menu again. The last option in this menu is “Add your devices”. This can be done if you would like to add a DVD player or STB.
5. Channel options a. Reordering channels Check if PBS Menu is active. Press “Home” button to see the guest menu. If the menu is displayed with “Add new device” and “Help”, the PBS Menu is not active. If the menu is displayed without “Add new device” and “Help”, the PBS Menu is active and TV menu has restrictions. Also in the Guest menu are options that will not be displayed if PBS Menu is active.
The PBS menu will appear like in picture. Using the arrow keys you can navigate through this MENU. To disable PBS mode use arrow keys to select the “OFF” option and confirm with “OK”. The previous menu will be active, use left arrow to go the base menu of the PBS menu. Go to “Store” option down the bottom of the menu and press “OK”.
When you press “OK” the next image will appear and you will have to confirm. After the confirmation the TV will restart. After power on all PBS settings will be disabled. This menu will allow you to set up channels, reinstall channels, change picture settings, add new devices. As you can see in the picture you have two new sections: “Add new device” and “Help”. Press “OK” button on remote control for the channel grid. All installed channels are available on this menu.
Select “Reorder” and Press “OK” button on the remote control to reorder channels. Navigate to the channel that you want to move and Press “OK” on the remote control to select that channel. The arrows around the channel indicate that the channel is selected and can be moved. Use arrow keys to move the channel to the new position. When you reached the new position press “OK” on the remote control to confirm the new position of the channels.
When you are finished with the re-ordering press “Options” on the remote control again. Press “OK” on the remote control to confirm that you are done with the re-ordering. b. Rename channels Select the channel, press the “Options” button on the remote control and select “Rename” to change name of a channel. If you then press the “OK” button a virtual QWERTY keyboard will pop up. c. Hide channels Important: You cannot delete channels from the channel grid, but you can use the option to hide the channels.
6. PBS Mode [Off]: The TV operates as a basic (consumer) TV. [On]: All settings in the PBS mode Setup menu are active. Only by switching on this mode the TV acts as a Hospitality TV. Sets the room ID. Room ID can be used to distinguish between different floors/rooms/setups when using SmartInstall. A shortcut to enter the consumer installation menu. Consumer installation menu should be accessed to change e.g. picture and sound settings and update channels.
When the TV is switched on it will start up on the specified source/channel. Available EXT1, EXT2, VGA, HDMI, HDMI side, AV side or one of the installed TV channels. When the TV is switched on it will start up on the specified volume level. Selectable value from 00 until 60. This specifies the maximum allowable volume level of the TV. Selectable value from 00 until 60. When the TV is switched on it will start up on the specified picture format.
[On] To enable the welcome message. [Off] No welcome message Line 1: First line of welcome message. Line 2: Second line of welcome message. Clear: Will delete the message enter on welcome message. When pressing “OK” button on remote control while editing line 1 or 2, a virtual keyboard will pop up on screen. Maximum 20 characters per line. Sets the period of time to display the welcome message on the screen when TV is turned on from standby. Selectable values: 20, 25, 30 seconds.
[Off]: TV responds to commands guest remote control. [On]: TV does not respond to commands guest remote control. Master remote control 22AV8573 (yellow) or RC2573 (green) commands are not affected by this setting. [Off]: On Screen Display suppressed. [On]: On Screen Display not suppressed. [Off]: PBS setup menu can be accessed by both Guest remote control and Master remote control 22AV8573 (yellow) or RC2573 (green). Guest remote control access to set up menu only possible with code 3,1,9,7,5,3, mute.
[Off]: Disables teletext. [On]: Enables teletext. [Off]: Disables MHEG. [On]: Enables MHEG. [Off]: Disables EPG. [On]: Enables EPG. [Off]: Closes subtitles. [On]: Displays subtitles. [On during mute]: Displays subtitles when audio is muted. [Off]: Disables USB multimedia function. [On]: Enables USB multimedia functions. Feature is not influencing cloning and/or software upgrade via USB. [Off]: The background color is set to black in case of no video signal on selected source.
Defines the time interval between numeric buttons when users press digits on the remote control. Selectable values from 0.5 to 9.9 seconds. Allows the installer to define which external sources to be displayed on the source list when pressing AV button on the Guest remote control. Only the sources marked [X] appear in the source list. To select channel to download clock information. Correct clock information is needed to provide correct EPG data and to have MyChoice working.
[Off]: The volume +/- on the Guest remote control will affect both the TV Main speaker and the headphone volume. [On]: The volume +/- on the Guest remote control will affect both the TV Main speaker and the headphone volume. After pressing “MUTE”, the volume +/- on the Guest remote control will not reactivate the TV Main speaker volume, but will only control the headphone volume. Set the default volume level for TV Main speaker after “Unmuting”.
To set the color of the TV in multi remote. Guest remote control supports up to four televisions operating in one room without interference from each other’s remote controls. Each TV and a Guest remote control can be set to match. Selectable values: Blue, Green, Yellow, Red. [Off]: Disables MyChoice function. [On]: Enables MyChoice function.
This will store all settings and restart TV to apply all changes. After storing PBS settings, the TV will restart to apply the new parameters. Now you can clone all settings to other TV sets by using the option TV to USB and USB to TV. Check how to clone settings.
7. Welcome Logo Startup time takes up approximately 7 seconds File format: 1280 x 720 / PNG / NO layers / 256 colors Note: below timing values are approximate indications and can differ from real situation! How to upload Welcome Logo 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Create graphics file: 1280 x 720 / PNG / NO layers / 256 colors. File name: TPM63HE_WelcomeLogo.
8. Cloning On the USB which is containing the software upgrade you can clone the settings. The instant initial cloning will first upgrade de software version and after will clone the settings from USB key. Folders generate by TV on USB key are: –TPM61HE (42HFL3233) –TPM64HE (32HFL3233) –TPM63HE (22/26HFL3233) Cloning 22 and 26 inch can be exchanged. For Welcome logo and Hotel Logo you have to use, the correct name for files and folders (case-sensitive). 9.
11. CSM (Consumer Setup menu) The CSM contains data about the TV software, serial number and other details. The menu can be accessed using a standard remote control or using the master remote control. 1. Using the standard remote control: press the following key sequence “1,2,3,6,5,4” 2. Using master remote control (22AV8753D): Press the RECALL button, available only if PBS mode is ON. Notes: Activation of the CSM is only possible if there is no (user) menu on the screen.