Register your product and get support at www.philips.
Contents 1 Important 3 2 Your Docking Speaker 4 Introduction What's in the box Overview of the main unit 3 Get started Connect power Turn on 4 Play Play from iPod/iPhone Play from an external device Adjust volume 5 Product information 4 4 4 5 5 5 6 6 9 9 10 6 Troubleshooting 10 7 Notice 11 Disposal of your old product and batteries 11 EN 2
1 Important 3 Read these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or produce heat.
2 Your Docking Speaker Overview of the main unit Congratulations on your purchase, and * 7 8 ; " support that Philips offers, register your product at www.philips.com/welcome. If you contact Philips, you will be asked for the model and serial number of this apparatus. The model number and serial number are on the bottom of the apparatus. Write the numbers here: Model No. __________________________ Serial No.
3 Get started Always follow the instructions in this chapter in sequence. 1 2 Open the battery compartment. 3 Close the battery compartment. Insert 4 x 1.5V AA batteries with correct ? @ % Connect power This docking speaker can be powered by either AC power or batteries. Option 1: AC power Caution Risk of product damage! Make sure that the power supply voltage matches the voltage printed on the bottom of the unit.
Switch to standby mode The docking speaker switches to standby mode in the following situation: Press again; The speaker is idle for 15 minutes when powered by AC supply. The iPod/iPhone or external audio device is disconnected when the speaker is operated on batteries. » The / LED indicators light off. 4 Play Play from iPod/iPhone You can enjoy audio from your iPod/iPhone through this docking speaker.
2 Insert the iPod/iPhone into the dock. 3 X @ $ * " # install DockStudio app on your iPod/ iPhone. 4 Tap [Yes] request. 5 Follow the on-screen instructions to complete the installation. Tip With the DockStudio app, you can enjoy music, set clock and alarm, adjust sound settings, and update * % Z * " $ DockStudio app will search for it automatically and ask you to download it.
1 Z * * $ OK. 2 Follow the on-screen instructions to * % Note Do not disconnect power or undock the iPod/iPhone during the updating process. Charge the iPod/iPhone Note If the docking speaker is operated on the batteries, you cannot charge your iPod/iPhone. When the docking speaker is connected to AC power, the docked iPod/iPhone begins to charge. Tip For certain iPod models, it may take up to a minute before the charging indication appears.
Sync iPod/iPhone with PC 3 Play audio on the device (see the device's % Note \ # ; " your PC. 1 2 Insert the iPod/iPhone in the dock. Press to switch to standby mode. » The LED indicators light off. 3 Connect your docking speaker and PC with a USB cable. 4 Launch iTunes to synchronize your docking speaker with PC. » The docked iPod/iPhone is synchronized with PC successfully through the iTunes.
5 Product information 6 Troubleshooting Warning Never remove the casing of this apparatus. Note Product information is subject to change without prior notice. Rated Output Power 2 X 5 W RMS General information Power supply - AC Power - Battery Model: AS190-090{| } 7 ~ Input: 100-240 V ~, 50/60Hz, 0.7A; Output: 9 V 1.9 A; 4 x AA batteries <10 W Operation Power Consumption Standby Power <0.5 W Consumption Max.
7 Notice Please visit www.recycle.philips.com for additional information on a recycling center in your area. { device that are not expressly approved by Philips Consumer Lifestyle may void the user’s authority to operate the equipment. Environmental information All unnecessary packaging has been omitted.
Specifications are subject to change without notice © 2012 Koninklijke Philips Electronics N.V. All rights reserved. DS3100_78_UM_V1.
