Register your product and get support at www.philips.
Contents 1 Important 3 2 Your Docking Speaker 4 3 Get started 6 4 Play 7 Introduction What’s in the box Overview of the main unit Overview of the remote control Prepare the remote control Connect power Turn on Play from iPod/iPhone/iPad Play from Bluetooth devices Play from an external audio device Adjust volume Mute sound 4 4 5 6 6 6 7 7 9 10 10 10 5 Specifications 11 6 Troubleshooting 11 7 Notice 12 Amplifier Bluetooth General information About Bluetooth device 11 11 11 12 EN 2
1 Important • • • • • • • • • • • • • • • • 3 Read these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
2 Your Docking Speaker Congratulations on your purchase, and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/welcome. If you contact Philips, you will be asked for the model and serial number of this apparatus. The model number and serial number are on the bottom of the apparatus. Write the numbers here: Model No. __________________________ Serial No.
Overview of the main unit c a b d f e a Dock for the iPod/iPhone/iPad b c 5 • • / • • • EN Adjust volume. As LED indicators, show system status. Select Bluetooth mode. Turn the docking speaker on. Switch to standby mode. d Power supply socket • Connect AC power. e • Sync with PC through a USB cable. f MP3-LINK • Connect an external audio device.
3 Get started Overview of the remote control Always follow the instructions in this chapter in sequence. f a e b d c Prepare the remote control For first-time use: Remove the protective tab to activate the remote control battery. To replace the exhausted battery: 1 2 3 Open the battery tray. Insert one CR2025 battery with correct polarity (+/-) as indicated. Close the battery tray. CR2025 a b c d e f • • • Select iPod/iPhone/iPad mode. / Skip to a track. Search within play. • Mute volume.
Connect the AC power adaptor to: • the DC IN socket at the back of the docking speaker. • the wall outlet. 4 Play Play from iPod/iPhone/iPad You can enjoy audio from iPod/iPhone/iPad through this docking speaker. Compatible iPod/iPhone/iPad Turn on Press and hold on the main unit for 2 seconds. »» The / LED indicators light up. Switch to standby mode In the following situation, the docking speaker switches to standby mode: • Press and hold for 2 seconds again; or • The system is idle for 15 minutes.
2 3 4 5 6 1 For first-time use, you will be asked to install DockStudio app on your iPod/ iPhone/iPad. If a new firmware update is found, tap OK. Tap [Yes] (yes) to accept the installation request. Follow the on-screen instructions to complete the installation. Launch the app after the installation. Play audio on your iPod/iPhone/iPad. »» Audio comes out through this docking speaker. 2 Follow the on-screen instructions to complete the firmware update. Tip •• You can press to select Dock source.
4 Launch iTunes to synchronize your docking speaker with PC. »» The docked iPod/iPhone/iPad is synchronized with PC successfully through the iTunes. Note •• Due to different materials and product techniques, some USB cables may not work with this device. Play from Bluetooth devices Note Note •• Do not disconnect power or undock the iPod/iPhone/ iPad during the updating process.
Play from an external audio device 1 2 If no iPod/iPhone/iPad is docked, connect an MP3 link cable (3.5mm, not supplied) to: • the MP3-LINK socket at the back of the docking speaker. • the headphone socket on an external device. Play music on the device (see the device’s user manual). Tip 3 4 5 •• You can select MP3 link source by pressing Scan Bluetooth devices that can pair with your device. When “PHILIPS DS3600” is displayed on your device, select it to start connection.
5 Specifications Note Warning •• Product information is subject to change without prior notice. Amplifier Rated Output Power Signal to Noise Ratio Aux-in Link 2 X 10 W RMS > 62 dBA 500mV RMS Bluetooth Standard Output power Frequency band Range Bluetooth Standard Version 2.1+EDR 0 dBm (Class 2) 2.402 ~ 2.480 GHzISM Band 10 m (free space) General information AC Power Operation Power Consumption Standby Power Consumption Max.
About Bluetooth device Music playback is unavailable on the system even after successful Bluetooth connection. •• The device cannot be used with the system to play music. The audio quality is poor after connection with a Bluetooth-enabled device. •• The Bluetooth reception is poor. Move the device closer to the system or remove any obstacle between the device and the system. Cannot connect with the system. •• The device does not support the profiles required for the system.
When this crossed-out wheeled bin symbol is attached to a product it means that the product is covered by the European Directive 2002/96/ EC. Please inform yourself about the local separate collection system for electrical and electronic products. Please act according to your local rules and do not dispose of your old products with your normal household waste. Correct disposal of your old product helps to prevent potential negative consequences for the environment and human health.
Specifications are subject to change without notice © 2012 Koninklijke Philips Electronics N.V. All rights reserved. DS3600_05_UM_V1.
