Table of contents AIntroduction .................................... 3 Dear Philips customer, .................................................................................... Regional code .................................................................................................... Technical data ................................................................................................... Accessories .........................................................................................
JProgramming a recording (TIMER) .............................................. 62 General ............................................................................................................. Programming recordings with the ShowView® System ......................... Programming recordings without the ShowView® System ................... How to change or delete a programmed recording (TIMER) ............. 'NexTView Link' .............................................................................
MONITOR Monitor: This button lets you switch between the TV receiver (internal tuner) in the DVD recorder (TV picture on the TV set) and playback on the DVD recorder. STANDBY m Switch on or off: To switch set on or off, interrupt menu function, interrupt a programmed recording (TIMER) TV/DVD TV/DVD switch: Switches the scart socket EXT 2 AUX-I/O directly to the TV set.
N Select previous title/search backwards : Briefly press the button during playback: Previous chapter/film or previous title Hold down the button: Search backwards Hold down button during still picture, slow motion backwards O Select next title/search forwards : Briefly press the button during playback: Next chapter/film or next title Hold down the button: Search forwards Hold down button during still picture, slow motion forwards STOP h Stop: Stop playback/recording, except with programmed recordings
ENGLISH Front of the device STANDBY/ON m Switch on or off: To switch off or on, interrupt a function, interrupt a programmed recording (TIMER) OPEN/CLOSE J Open/close disc tray: Open/close disc tray RECORD Record: Record the current TV channel G Playback: To play a recorded disc N Select previous title/search backwards O Select next title/search forwards h Stop: Interrupt playback/recording Behind the flap at the right hand corner on the front S-VIDEO S Video socket: Connection of SVHS/Hi8
Back of the unit 4MAINS Mains socket: Connection to the mains supply (230V/50Hz) ANTENNA IN Aerial input: Connection of the aerial TV OUT Aerial output: Connection of the TV set EXT 2 AUX-I/O Scart socket 2: Connection of an additional device (satellite receiver, set-top box, video recorder, camcorder, etc.) EXT 1 TO TV-I/O Scart socket 1: Connection of a TV set.
Disc bar: Displays the current position on the disc (disc pointer). Play/Record: Single flashing segment at the current position. Pause: Flashing segment on both sides of the current position. Stop: Illuminated segment at the current position. SAT A satellite recording has been programmed.
EMPTYDISC The disc inserted is either new or has been completely erased (no recordings). PROTECTED The disc is protected against recording. MAX TITLE The maximum number of titles per disc has been reached. The maximum number of titles per disc is 48. MAX CHAP The maximum number of chapters per title/disc has been reached. The maximum number of chapters per title is 124. DISC FULL The disc is full. There is no space for new recordings PAL DISC A disc with PAL recordings has been inserted.
A Introduction Dear Philips customer, Allow me to introduce myself. My name is Phil. I will be guiding you through the instruction manual and helping you get to know your new DVD recorder. At appropriate points along the way, I will be providing you with the following information: Question: (?) Here I will be explaining seemingly unimportant things. Tip Here I will be giving you instructions on functions that will make it easier for you to use your DVD recorder.
Welcome to the growing family of owners of PHILIPS equipment. Thank you for buying a DVDR 75/001-75/021 . Please take the time to read this operating manual before using your DVD recorder. It contains important information on how to set up and operate the machine. The video recorder should not be turned on immediately after transportation from a cold to a hot area or vice versa, or in conditions of extreme humidity. Wait at least three hours after transporting the machine.
Discs you can use ENGLISH The following discs can be used in your DVD recorder for playback and recording: Playback and recording DVD+RW (Digital Versatile Disc + rewritable) DVD+R (Digital Versatile Disc + Recordable) Playback only: DVD Video (Digital Versatile Disc) DVD-R (DVD-Recordable) DVD-RW (DVD-Rewritable) These discs can only be played back if the recording was made in video mode and the recording was finalised.
Regional code Since DVD films are not normally released in all parts of the world at the same time, all DVD players have a specific regional code. Discs can be given a regional code. If the regional codes differ between the player and the disc, playback is not possible. DVDs must be marked 'ALL' for all regions or '2' for region 2 to work in this machine. If the DVD is marked with a different region, it cannot be played in this DVD recorder. The number within the globe represents the region.
Important ENGLISH Caution: Visible and invisible laser radiation. If the cover is open, do not look at the beam. Because of the risk of eye injuries, only qualified service engineers should open the machine and carry out maintenance or repair work. LASER Type: Semiconductor lasers InGaAlP (DVD), AlGaAs(CD) Wavelength: 660nm (DVD), 780nm (CD) Output power (outside the lens): 20mW (DVD+RW write), 0.8mW (DVD read), 0.3mW (CD read). Beam divergence: 82 degrees (DVD), 54 degrees (CD) Danger.
When installing the recorder in a cupboard ensure there is a gap of approximately 2.5 cm (1 inch) around the recorder to enable air to circulate freely and prevent overheating. Make sure that air can circulate freely through the ventilation slots on the machine. The machine should be placed on a firm surface. Make sure that no objects or liquids enter the video recorder. Do not place vases or similar on the DVD recorder.
Special functions of your DVD recorder Philips provides the best possible connection between your DVD recorder and other home cinema equipment. The DVD recorder is controlled by external devices (receivers, TV sets and so on) via Cinema Link and is automatically set to the right system settings. This function automatically transfers all the television channel settings onto your DVD recorder via the scart cable ( EXT 1 TO TV-I/O socket).
Dolby Laboratories standard for transmitting 5.1 channels. Five full-value channels are transmitted in this acoustic playback system. A further channel is used for low frequencies (effects). The loudspeakers are arranged front left, front middle, front right, rear left and rear right. This system is currently the most common system and is used in cinemas. With this DVD recorder each soundtrack in 2-channel Dolby Digital is recorded onto a DVD+RW. Manufactured under license from Dolby Laboratories.
B Connecting the DVD recorder The remote control and its batteries are packed separately in the original DVD recorder packaging. You must install the batteries in the remote control before use - described in the following section. 1 Take the remote control and the enclosed batteries (2 batteries). 2 Open the battery compartment, insert the batteries as shown and then close the battery compartment. The remote control is now ready to use. Its range is approximately 5 to 10 meters.
When you install your DVD recorder for the first time, select one of the following options: 'Connecting with a scart cable and Easy Link' If your TV set is equipped with 'Easy Link, Cinema Link, NexTView Link, Q-Link, Smart Link, Megalogic, Datalogic, ...' and you wish to use a scart cable. 'Connecting with a scart cable without Easy Link' If your TV set is not equipped with 'Easy Link, Cinema Link, NexTView Link, Q-Link, Smart Link, Megalogic, Datalogic, ...' and you wish to use a scart cable.
EasyLink loading data from TV; please wait Switch on the TV set. 6 Insert one end of the supplied mains cable into the mains socket 4MAINS at the back of the DVD recorder and the other end into the wall socket. 7 A message appears on the screen announcing that the transfer has started. 'EASYLINK' appears on the display during transfer. The TV set transfers all saved TV channels, in the same order, to the DVD recorder. This may take several minutes.
Connecting with a scart cable without 'Easy Link' Have the following cables ready: an aerial cable (1, supplied), a mains cable (2, supplied), a scart cable (3). 1 Remove the aerial cable plug from your TV set. Insert it into the ANTENNA IN socket at the back of the DVD recorder. 2 Insert one end of the supplied aerial cable into the TV OUT socket at the back of the DVD recorder and the other end into the aerial input socket at the back of the TV set.
a My screen is empty. b Many TV sets are switched by the DVD recorder to the programme number for the scart socket by way of a control signal sent through the scart cable. b If the TV set does not automatically switch to the scart socket programme number, manually change to the corresponding programme number on your TV set (see your TV's operating instructions). b Check that the scart cable is connected from the TV set to the EXT 1 TO TV-I/O socket on the DVD recorder.
4 Insert one end of the audio (Cinch) cable into the red/white Cinch socket OUT L AUDIO R at the back of the DVD recorder and the other end into the audio input socket (usually red/white) on the TV set (usually labelled 'Audio in' or 'AV in'. See TV operating instructions). 5 Switch on the TV set. Switch the TV set over to the SVHS input socket or select the relevant programme number. Please see your TV's operating instructions for the programme number you need.
Insert one end of the video (CVBS) cable into the yellow Cinch socket OUT VIDEO (CVBS) at the back of the DVD recorder and the other end into the video input socket (usually yellow) on the TV set (usually labelled 'Video in' or 'AV in'. See TV operating instructions).
C Connecting additional devices Connecting additional devices to the second scart socket You can connect additional devices such as decoders, satellite receivers, camcorders, etc. to the EXT 2 AUX-I/O socket. When playback is started on this additional device the DVD recorder automatically connects the EXT 2 AUX-I/O scart socket with the EXT 1 TO TV-I/O scart socket. You will then see the picture from the additional device on your TV set, even if the DVD recorder is switched off.
Connect camcorder to the front sockets Best picture quality If you have a DV or Digital 8 camcorder, connect the DV IN input of the DVD recorder to the appropriate DV output on the camcorder. When films are transferred the original recording date and time are stored as DVD subtitles. On playback, this data can be displayed on the TV screen by using the 'E' function (Subtitle).
Connecting audio devices to the digital audio socket At the back of the DVD recorder there is a digital audio output socket DIGITAL AUDIO OUT for an coaxial cable. These can be used to connect the following: •) an A/V receiver or an A/V amplifier with a digital multi channel sound decoder •) a receiver with two channel digital stereo (PCM) Digital multi channel sound Digital multi-channel sound offers the best possible sound quality.
D Installing your DVD recorder Initial installation ENGLISH After successfully connecting your DVD recorder to the TV set and other additional devices as described in the previous chapters, this chapter will show you how to start the initial installation. The DVD recorder automatically seeks out and stores all available TV channels. Connecting additional devices If you have connected additional devices such as a satellite receiver to the aerial cable, switch them on.
7 Virgin mode TV Shape 4:3 letterbox 4:3 panscan 16:9 Select the desired screen format position using CH- B or CH+ A . These settings will only be used if you insert a DVD that contains this information. Which screen formats can I select? '4:3 letterbox' Press OK to continue '4:3 panscan' '16:9' for a wide-screen TV set (screen edge ratio 16:9) Confirm with OK . 9 Select the country of your residence with CH- B or CH+ A . If your country does not appear, select 'Other'.
 Check if the displayed settings for 'Year', 'Month' and 'Date' are correct. à When all information is correct, save by pressing OK . ENGLISH The initial installation is now complete. Satellite receiver If you are connecting a satellite receiver, please read the section on 'Using a satellite receiver'. Decoder If you are connecting a decoder, you must install it as described in the next section. a Sound may be distorted on some TV channels.
Allocating a decoder Some TV channels send coded TV signals that can only be viewed properly with a purchased or rented decoder. You can connect such a decoder (descrambler) to your DVD recorder. The following function automatically activates the connected decoder for the TV channel you want to watch. How do I allocate the decoder for Easy Link? If your TC=V set supports 'Easy Link' the decoder must be assigned to the relevant TV channel on the TV set (see the operating instructions for your TV set).
In some cases, not all of the available TV channels may have been found and stored during initial installation. In this case, you will need to search for and store the missing or coded TV channels manually. Manual search with EasyLink With 'Easy Link', the DVD recorder will automatically download the TV channels stored on the TV set. This is why some lines have no function. To store new TV channels, they must first be stored on the TV set.
How can I change the symbol of a TV channel? 1 In 'TV channel name', press C . 2 Select the desired symbol position using D or C . 3 Change the symbol at the symbol position with CH- B or CH+ A . 4 Select the next symbol position in the same way. 5 Keep pressing C until the cursor disappears. Tip How can I change the TV system of the TV channel? In 'TV system', use D or C to select the TV system that produces the least distortion of picture and sound.
TV 01 Switch on the DVD recorder using STANDBY/ON m . 3 Press the SYSTEM-MENU button on the remote control. The menu bar appears. 4 Select 'A' symbol with D or C . 5 Select 'Installation' using CH- B or CH+ A and confirm with C . 6 Select line 'Follow TV' with CH- B or CH+ A . and confirm with the C button. 7 Confirm the message on the screen with OK . 'TV 01' will appear in the DVD recorder display. 8 Select programme number '1' on the TV set.
Automatic TV channel search During installation, all available TV channels are searched for and stored. If the channel assignments of your cable or satellite TV provider change or if you are reinstalling the DVD recorder, e.g. after moving house, you can start this procedure again. This will replace the stored TV channels with the new ones. What does Easy Link do? With Easylink, you can search for and store TV channels only on the TV set. These settings are accepted by the DVD recorder.
After you have performed the automatic channel search you may not agree with the sequence in which the individual TV channels have been allocated to the programme positions (programme numbers). You can use this function to rearrange the TV channels already stored or to delete TV channels you don't want or those with poor reception. EasyLink With Easylink, you can search for and store TV channels only on the TV set. These settings are then accepted by the DVD recorder.
Setting the language/country You can select the country and, for DVD playback, the language for the subtitles and the audio language. Please note that with some DVDs the audio language and/or subtitle language can be changed only via the DVD menu. For bilingual shows you can also select the sound channel of the TV station for recording. You also have the option of setting one of the displayed languages for the on-screen menu (OSD).
Audio Language Recording audio Subtitle Menu Country Language English Language 1 English English Other Switch on the TV set. If required, select the programme number for the DVD recorder. 2 Switch on the DVD recorder using STANDBY/ON m . 3 Press SYSTEM-MENU on the remote control. The menu bar appears. 4 Select 'A' symbol with D or C . 5 Select line 'Language' with CH- B or CH+ A . and confirm with the C button. 6 Select line 'Recording audio' and confirm with C .
E On screen information You can check or change many of the functions and settings of your DVD recorder via the system menu bar. The menu bar cannot be displayed during recording. Symbols in the menu bar Press SYSTEM-MENU to open and close the menu bar (main menu). Use D and C to select the relevant function. Use CH- B to confirm the function and go either to another menu or execute the function directly. Some functions may not be available, depending on the disc inserted.
The top left corner of the menu line contains a field for temporary messages relating to the various operating modes.
Operating mode symbols R S T U V X Y Z Recording Stop Playback Playback Pause Record Pause Search forwards (8x speed) Search backwards (8x speed) Slow motion Tuner information box This field is located in the bottom left-hand corner of the screen. The aerial signal, the TV channel and the TV channel name for the selected programme are displayed.
F playback With this DVD recorder you can play back the following systems: •) DVD Video •) (Super)Video CD Disc •) DVD+RW Disc •) DVD+R Disc •) DVD-RW (video mode, finalised) •) DVD-R •) CD-R •) CD-RW •) Audio CD •) MP3 CD You can operate the video recorder using the remote control or the buttons on the front of the DVD recorder. a The display will read 'PIN' b The child lock has been activated for the inserted disc.
Opening/closing the tray using the remote control You can open and close the disc tray using the remote control. Press and hold the STOP h button on the remote control until the dialog box shows 'OPENING' or 'CLOSING'. 3 Tip Playback starts automatically. A menu may appear when a DVD is played back. If the titles and chapters are numbered, press a number button on the remote control. You can also use the D , C , CH+ A , CH- B buttons or number buttons 0..9 to select a menu item and confirm with OK .
C01 ANNA P01 1 If the disc is write-protected or a finalised DVD+R disc, playback starts automatically. 2 If playback does not start automatically, use the CH- B or CH+ A button to select the title you want to play on the index screen. You can also use the N or O button on the front. 3 Press the PLAY G button. This will appear on the display: title number, recording quality. a I can see the message 'EMPTYDISC' b The disc does not contain any recordings.
Playing an MP3 CD MP3 (MPEG1 Audio Layer-3) files are highly compressed music files. Using this technology the data volume can be compressed by a factor of 10. This means it is possible to record 10 hours of music in CD quality on a single CD-ROM. When creating MP3 CDs please note the following: File system: ISO9660 Directory structure: maximum of 8 levels Formats: *.mp3 Filenames: maximum of 12 characters (8+3) Maximum of 32 albums, 999 titles Supported sampling frequencies: 32, 44.1, 48 (kHz).
(Super) Video CDs may be equipped with PBC (Play Back Control). This means that special playback functions (menus) can be directly selected. The video CD must be PBC compatible (see CD case). 'PBC' is active in the default settings. playback 1 Insert a (Super) Video CD. If the 'h' symbol appears in the display, start playback by pressing PLAY G .
G Additonal playback features Changing to another title/chapter If there is more than one title or chapter on a disc you can change to another title or chapter as follows. However if there are several chapters within a title, these will be selected. The title can then still be selected via the menu bar. 1 During playback, press O to go to the next title/chapter. Press N to return to the start of the current title/chapter. Press N twice to return to the start of the previous title/chapter.
Still picture 2:04 During playback, press PAUSE 9 to stop playback and display a still picture. ENGLISH C01 1 Frame advance via menu bar 1 During a still picture press SYSTEM-MENU on the remote control. The menu bar will appear at the top of the screen. ' symbol using C or D and confirm with CH- B . 3 You can now use the D or C button to go forwards or backwards one frame at a time. 4 If necessary, switch the menu bar off with the SYSTEM-MENU button.
3 Enter the start time with the digit keys 0..9 from where playback should start. 4 Confirm with OK . a The time entered will flash on the screen b The selected title is shorter than the time entered. Enter a new time or cancel the function by pressing SYSTEM-MENU . 5 Problem Playback starts at the time you entered. Repeat/Shuffle play You can mark entire sections or the whole disc for endless playback.
Scan feature 1 During playback, press PLAY MODE . Select ' ' using PLAY MODE . 2 After 10 seconds the DVD recorder switches to the next chapter/index. To start playback at the relevant chapter/index press STOP h and then PLAY G . ENGLISH This feature plays back the first 10 seconds of each chapter (DVD) or track (CD). Camera angle If a DVD contains scenes that have been shot from different camera angles you can select these camera angles for playback. 1 During playback, press PAUSE 9 .
6 Confirm with OK . 7 To stop the feature, press PLAY G and then SYSTEM-MENU . Select the audio language Many pre-recorded DVD discs have more than one audio language. The language initially selected for playback will be the one you selected when you first set up the DVD recorder. However you can change the audio language of the inserted disc at any time. You can change the audio language either using the menu of the inserted disc ( DISC-MENU button) or the AUDIO button.
H Manual recording General DVD+R This type of disc can only be recorded once. If you want to play this DVD in a DVD player it must be finalized using the 'Finalise disc' function. It is not possible to make further recordings using this disc. If this disc is to be played in a DVD recorder it must not be finalised. Recordings can be added and deleted.
Recording without automatic switch off 1 Switch on the TV set and select the programme number for the DVD recorder. 2 Insert a disc on which the recording is to be made. This disc is then checked for content and system. READING' will appear on the display. a Index display b A DVD+RW disc has been inserted that already contains recordings. Use the CH+ A or CH- B button to select the point where the recording is to start.
1:16:51 P01 Insert chapter markers During recording you can mark scenes so you can find them or hide them later. During recording, press FSS & at the start point. 'Inserting marker' appears on the TV screen. In the display, the number of the 'CHAPTER' increases by one. For further information on titles and chapters, see the section on 'Changing to another title/chapter' in 'Playback'. 6 ENGLISH C01 Tip Use the STOP h button on the remote control or h on the machine to stop the recording.
Recording with automatic switch off (OTR one touch recording) 1 Insert a disc. 2 If necessary, use the MONITOR button on the remote control to switch to the internal tuner in the DVD recorder. 3 Use CH+ A or CH- B to select the programme number (channel name) you want to record. 4 Press REC/OTR n on the remote control. 5 Each time you press REC/OTR n you will add 30 minutes to the recording time.
The entire disc is now protected. If an attempt is made to record on a protected disc, 'DISC LOCK' will appear on the display and 'Disc locked' will appear on the screen. ENGLISH Lining up recordings within a title (assemble cut) On a recorded DVD+RW disc you can add another recording to an existing title. This recording is added to the title as a 'chapter'. The existing information will be overwritten starting from this point.
Selecting the recording type (Quality) You can select the picture quality of the recording using the recording quality feature and hence the maximum recording time per disc. You can check the quality by changing the recording mode and then watching the picture from the built-in tuner ( MONITOR button). During playback, the correct picture quality will automatically be selected. 1 Switch on the TV set. If required, select the programme number for the DVD recorder.
You can use this function if you own a satellite receiver that can control other devices via a scart cable and a programming function (timer). For more information, please see the operating instructions for the satellite receiver. 1 Switch on the TV set. If required, select the programme number for the DVD recorder. 2 Press SYSTEM-MENU on the remote control. The menu bar appears. 3 Select 'A' symbol with D or C . 4 Select 'Record settings' using CH- B or CH+ A and confirm with C.
Direct Record Can you record the right TV channel in seconds when the DVD recorder is switched off? No problem. If recording is started manually, the switched off DVD recorder takes the current TV channel from the TV set via the scart cable. You will find more information on how to switch 'Direct record' on or off in the next section 'Direct record'. How does Direct Record work? The DVD recorder compares the TV channel selected on the TV set with its stored TV channels via the scart cable.
Manual recording 1 Switch on the TV set. If required, select the programme number for the DVD recorder. 2 Press SYSTEM-MENU on the remote control. The menu bar appears. 3 Select 'A' symbol with D or C . 4 Select 'Record settings' using CH- B or CH+ A and confirm with C. 5 Select 'Direct Record' using CH- B or CH+ A . 6 Select 'On' (Direct Record on) or 'Off' (Direct Record off) using D or C . 7 Confirm with OK . 8 To end, press SYSTEM-MENU . 9 Switch off with STANDBY m .
I Managing the disc contents General Charly 1 00:29:59 • M1 Fri15/02/2003 Empty title 01:30:01 When a recording is made to disc, the following additional information is also stored at the beginning of the recording: •) Name of the recording If the TV station does not transmit a name, only the channel number and time will be stored as the name •) Length of the recording •) Record type (Quality) •) Date of the recording •) Index picture of the recording A marker will be set every 5-6 minutes if the 'Auto ch
In this menu you can adapt a title to suit your particular needs. You can insert/delete chapter markers, hide chapters, select a new index, or split up a title. Press FSS & on the remote control during recording to open this menu. Insert chapter markers During recording, you can set or delete chapter markers within a title. The maximum number of chapters per disc is 124 and 99 per title. If one of these limits is reached the following message will appear on the screen: 'Chapter limit'.
3 Using C select 'hidden'. The picture is shown darker. Switching quickly You can switch between show chapters ('visible') and hide chapters ('hidden') quickly and easily using SELECT . 4 Tip To end, press FSS & . During playback this chapter will be skipped. If the chapter is not visible, select 'visible' in step 3 with C . Deleting chapter markers Within a title you can delete either all markers or individual markers.
Changing the index picture 1 During playback, search for location of the new index picture. Press the PAUSE 9 button. 2 Press the FSS & button. The 'Favorite Scene Selection' menu appears on the TV screen. 3 Select line 'New index picture' and confirm with OK . 4 Start the change with OK . 'Updating menu' appears on the TV screen. ENGLISH Normally the first picture of a recording is used as the index picture. You can however choose any picture from the recording as the index picture.
Editing recording titles (name) Some TV stations transmit the title (name) of a programme. In this case, the name will be included automatically (e.g. 'ROCKY'). Otherwise, the only the programme number (programme name) and the time are stored as the name of the recording. The name of the recording can only be changed after the recording has been completed. 1 Press the STOP h button or during playback press DISC-MENU .
Deleting recordings/titles 1 Press the STOP h button or during playback press DISC-MENU . 2 Using CH+ A or CH- B select the title you want to delete and confirm with C . The title editing menu will appear. 3 Select 'Erase this title' using CH+ A or CH- B and confirm with OK . 'This will completely erase this title' appears on the TV screen.. 'Press OK to confirm'. 4 If you want to delete this title, press OK to confirm. Otherwise press D. 5 'Erasing title' appears on the TV screen.
Changing the disc name 1 In the 'Disc info display' press C . The 'Settings for' menu appears on the TV screen. 2 Select 'Disc name' using CH+ A or CH- B and confirm with C . 3 Using C or D select the position where the letter/number/icon is to be changed/re-entered. 4 Change the icon using CH+ A or CH- B . You can switch between upper and lowercase using SELECT . You can delete the character using CLEAR . 5 Repeat 3 and 4 until you have made the changes you want. 6 Save the new title with OK .
Finalising DVD+R discs 1 In the 'Disc info display' press C . The 'Settings for' menu appears on the TV screen. 2 Select 'Finalise disc' using CH+ A or CH- B and confirm with OK . ENGLISH This feature is required to play back a DVD+R disc in a DVD player. Once the disc has been finalised no further recordings or changes can be made. a 'Finalise disc' does not appear b Either there is no DVD+R disc inserted or the disc is already finalised. To end, press SYSTEM-MENU .
J Programming a recording (TIMER) General Use 'Programming a recording (TIMER)', to automatically start and stop a recording at a later date. The DVD recorder will switch to the right programme number and begin recording at the correct time. With this DVD recorder, you can pre-programme up to six recordings within a period of one month.
Thanks to this programming system, you no longer need to tediously enter the date, programme number, start and end times. All the information needed by the DVD recorder for programming is contained in the ShowView® programming number. This 9-digit ShowView® number is found in most TV listings magazine. 1 Switch on the TV set. If required, select the programme number for the DVD recorder. 2 Press TIMER on the remote control. The programming method selected last is marked.
6 Rec Mode M2 The decoded data appears after confirmation. You can go back and change the data. Select the appropriate input field with C or D . If required, make changes using CH+ A , CH- B or the number buttons 0..9 . To store Press OK 'Switching on 'VPS/PDC' in the 'Start' input field Select the 'Start' input field using C . Using SELECT switch on 'VPS/PDC' ('*' lights up). If you press SELECT again, you will switch 'VPS/PDC' off ('*' goes out). Timer ShowView system Date 01 VPS Prog.
Timer Timer programming Date 01 VPS Prog. Start PDC End BBC1 20:15 21:30 Mo-Fr/Weekly Press SELECT Rec Mode M1 1 Switch on the TV set. If required, select the programme number for the DVD recorder. 2 Press TIMER on the remote control. The programming method selected last is marked. 3 Select line 'Timer programming' with CH- B or CH+ A . and confirm with the C button. The information will appear on the screen. 4 Select the input field with D or C . 5 Enter information with buttons 0..9 .
How to change or delete a programmed recording (TIMER) Timer Timer List Date 01 -- VPS Prog. Start PDC End BBC1 20:15 * 21:30 ----- --:---:-- 1 Switch on the TV set. If required, select the programme number for the DVD recorder. 2 Press TIMER on the remote control. The programming mode selected last is marked. 3 Select 'Timer List' using CH- B or CH+ A and confirm with C . 4 Select the programmed recording (TIMER) you want to check, change or delete with CH- B or CH+ A .
PROBLEM SOLUTION The DVD recorder is not responding bWhile a programmed recording is being made, you cannot operate your DVD recorder manually. 'Switch off, timer recording' flashes on the TV screen. bThe DVD recorder was switched on several minutes before the start of a programmed recording. Error message: 'Insert recordable disc' bEither a disc has not been inserted or the disc cannot be used for recording. Insert a disc on The error message 'Disc locked' appears briefly on the screen.
K User preferences In this section you will learn how to set your user preferences on the DVD recorder. The symbols have the following meanings: . / 0 1 2 3 4 Picture setting Sound setting Language setting Additional settings Remote control settings Disc settings Recording settings Installation 1 Switch on the TV set. If required, select the programme number for the DVD recorder. 2 Press SYSTEM-MENU on the remote control. The menu bar appears. 3 Select 'A' using D or C and confirm with CH- B .
'Vertical video shift' Use this feature to adjust the position of the picture on your TV left or right using D , C to suit your TV set. By default the recorder is set to 'RGB'. Select 'S-Video' if you want to connect an S-VHS recorder. Sound settings Depending on which audio outputs are used, you can select the settings in this menu. If you only use the analogue audio output ( OUT L AUDIO R ), select the settings 'Off' in the 'Digital output' menu.
Language settings You can choose the following settings in this menu: 'Audio Language' Language Audio Language Recording audio Subtitle Menu Country English Language 1 English English Other Playback audio language 'Recording audio' Audio recording 'Subtitle' Subtitle language 'Menu' Screen menu language 'Country' 'Country' Additional settings You can select the following functions in this menu: 'Status box' Features Status box Standby Display On Off Bright Along with the on screen menu, the OSD (
'Standby' 'Low power': If the DVD-Recorder is switched off (button STANDBY m ), the clock display is also switched off. 'Off': If the DVD-Recorder is switched off (button STANDBY m ), the clock display is visible. 'Demo mode': If the DVD recorder is switched off with the STANDBY m button, a list of the most important features is shown in the display. 'Display' You can change the brightness of the display on the DVD recorder. This setting only affects the DVD recorder when it is switched on.
Disk feature menu In this menu you can make the changes that relate to the disc: 'Access control' Features Status box Standby Display On Off Bright Please read the next chapter on 'Access control (child lock)'. 'Auto resume' If playback of a pre-recorded DVD video disc or video CD is interrupted (button STOP h or OPEN/CLOSE J ) when the disc is reloaded (disc is started) playback starts at the precise location where it stopped. This applies not only to the current disc but to the last 20 discs played.
L Access control (Child Lock) This feature enables discs to be locked for children. When Child Lock is on, a 4-digit code (PIN) needs to be entered before a disc can be played. You can also decide whether the inserted disc should always be played or should be played only once, despite the child lock •)'Play always': This disc is stored in a memory with space for 50 child-safe discs. If more than 50 discs are stored, the last disc in the list is removed and the new disc is added.
Authorising a disc 1 Insert a disc. The access control box will appear after a short delay. 2 Using CH+ A or CH- B select 'Play once' or 'Play always'. 3 Enter your PIN code using the number buttons 0..9 . Double-sided DVDs may have a different ID for each side. For these discs, each side must be authorised. Multi-volume video CDs may have a different ID for each volume. For these CDs, each volume must be authorised.
Access control Auto resume Disc features Enter code… On 1 Switch on the TV set. If required, select the programme number for the DVD recorder. 2 Switch on the DVD recorder using STANDBY/ON m . 3 Press SYSTEM-MENU . The menu bar appears 4 Select the 'A' icon using D or C . 5 Select '2(Disc features)' using CH- B or CH+ A and confirm with C . 6 Confirm 'Access control' using C . 7 Enter a 4-digit code of your choice.
Changing the country The set filter values depend on the respective country. It is therefore necessary to enter the country to which these filter values apply. Access control Auto resume 76 Disc features Enter code… On 1 Switch on the TV set. If required, select the programme number for the DVD recorder. 2 Switch on the DVD recorder using STANDBY/ON m . 3 Press SYSTEM-MENU . The menu bar appears 4 Select the 'A' icon using D or C . 5 Select line '2(Disc features)' using confirm with C .
Access control Auto resume Disc features Enter code… On 1 Switch on the TV set. If required, select the programme number for the DVD recorder. 2 Switch on the DVD recorder using STANDBY/ON m . 3 Press SYSTEM-MENU . The menu bar appears 4 Select the 'A' icon using D or C . 5 Select '2(Disc features)' using CH- B or CH+ A and confirm with C . 6 Confirm 'Access control' using C . 7 Enter your four-digit PIN code. If the code is new, you may have to enter the code a second time as confirmation.
M Before you call an engineer If you have any problems using this DVD recorder, the reason may be one of the following. You can also call the customer service centre in your country. The telephone numbers can be found on the back of this instruction manual. Have the model number (MODEL NO) and the production number (PROD.NO) of your recorder ready. The serial number (PROD. NO.) is printed on the type plate at the back.
PROBLEM SOLUTION bThere is no recording on the disc: Change disc. bYou inserted the wrong disc type: Your recorder can play back the following disc types: DVD No playback on DVD recorder: select the correct programme number for the DVD recorder. bThe cable connecting the TV set and the DVD recorder has come loose: check the cable. bIt is possible that this (Super) Video CD contains a menu and the 'PBC' is switched off.
DEUTSCH ENGLISH PROBLEM Distorted sound coming from a connected hi fi amplifier The picture is distorted or black and white during playback No sound signal at the digital output SOLUTION bThe DVD recorder is connected to the 'Phono-input' of your amplifier: This socket is provided only for record players without a preamplifier. Select a different audio input. bThe TV system of the disc does not match that of your TV set (PAL/NTSC).
PHILIPS Philips Austria GmbH Triesterstrasse 64 1101 Wien AUSTRIA Tel: 0810 00 12 03 PHILIPS PORTUGUESA, S.A. Consumer Information Centre Rua Dr. António Loureiro Borge, nr. 5 Arquiparque, Miraflores P-2795 L-A-VEHLA PORTUGAL Phone: 352-1-4163063 OY PHILIPS AB Sinikalliontie 3, 02630 Espo Helsinki FINLAND puh.