Contents 5 How to use EasyKey 1 Important Information Unlock Safety Warning Disposal of used products and batteries 2 EasyKey Installation Unlock from Outside -With a PIN Code -With a Fingerprint -With a Key Tag/Card 03 Packing List Exploded Views Pre-install Instruction Installation Steps 3 Get to know your EasyKey 15 02 Unlock from Inside -With a Rotatory Knob -With a Functional Button -With an Infrared Sensor Lock -Auto/Manual Mode -Lock from Outside -Lock from Inside 08 Indoor Deadlock Mec
1 Important information 2 Easykey Installation Safety Caution Packing List ◆Before using Philips EasyKey, please read and understand all instructions. Damage caused by non-compliance with the instructions will not be covered by warranty. ◆Do not place the battery near fire sources to avoid explosion. ◆Use only the manufacturer-specified accessories/components. ◆Use only the alkaline batteries the product is equipped with, or use the same specification type of alkaline batteries.
Exploded Views Pre-install Instruction This product can be installed on 4 types of opening directions: left-out pull, right-in push, right-out pull and left-in push. Left-open Right-open Indoor Indoor Left-in push Outdoor Rightin push Outdoor Indoor Indoor Leftout pull Outdoor Rightout pull Outdoor Attention 1. Please choose proper installation kit as per the door thickness. 2.
Installation Steps 1 To drill the needed holes in the door as per the drilling template,then mount the mortise on the door frame. 2 Put the compressed spring and square shaft into the square shaft hole of the inside escutcheon accordingly. 6 Fasten the 4 anchor screws in the mortise. 3 To install the connecting screw tubes on the outside escutcheon, and put the compressed spring and square shaft accordingly into the square shaft holes.
3 Get to know Your EasyKey 4 How to set up your EasyKey Outside Escutcheon Pre-install Instruction ◆There are two modes for the EasyKey System: general mode and dual verification mode.
◆How to enter into Master Mode User settings Add a Fingerprint Delete a single User PIN Code Add a user PIN code 1 Light up the keypad. Enter [#], enter master PIN code and confirm with [#]. Enter [#], then enter master PIN code and confirm with [#]. 2 1 2 3 Enter [2] to add a user record, then enter [3] to add a user fingerprint, and the system will automatically number it and generate a voice prompt.
Delete all One-time PIN Codes Enter [#], enter master PIN code and confirm with [#]. 3 2 Enter [3] to delete a user record, then enter [2] to delete all one-time user PIN code. After hearing a voice prompt of “Succeeded”, press [*] until you exit the master mode. Delete All Fingerprints System Initialization Enter [#], enter master PIN code and confirm with [#]. Enter [#], then enter master PIN code and confirm with [#].
Extended Functions Local Query 5.How to use your EasyKey Unlock | Unlock from outside Enter [#], enter master PIN code and confirm with [#]. 6 2 5 Enter [5] to get into extended functions. 1 Enter [#], enter master PIN code and confirm with [#]. or 2 To join a network, press [1]. To exit a network, press [2]. Before setting up the extended functions, please download and open Philips EasyKey (APP) from App Stores via your phone.
Lock | Auto/Manual Mode Inside Deadlock When the EasyKey is locked, long-press the [CLOSE] button, after the indicator flashes once in red, and there will be a voice prompt of “Inside deadlock enabled”. [A] indicates auto mode, after closing the door, the latch bolt will pop up, and the door is lock. Attention Lock | Auto/ Manual switch Under inside deadlock mode, all functions of the outside escutcheon will be locked.
6 Other Functions Indoor Infrared Sensor Unlocking Rear inductive position Mute Mode Function: With indoor infrared sensor unlocking, you could easily unlock the door from inside. Front inductive position Infrared Sensor Functions: Use only one button to mute the lock by turning off the voice guide. Applicable to the scenes where you don’t want to disturb your family.
7 The use and meanings of indicators Mute mode indicator Lock Status Indicator The meanings of different light colors The meanings of different light colors 1. White: Indicates the mute mode is off. Blue: When the system wakes up, the light will glow blue, indicating that you can operate the lock. 2. Green:Indicates the mute mode is on. Green: When the door is unlocked, the light will glow green, indicating that the door is open.
[OPEN/CLOSE] Indicator Low Battery Voltage Alarm reminds you of replacing the batteries in time Triggering: After waking up, the system will run an automatic examination on the battery voltage. If the voltage is too low, the lock will give an alarm with a voice prompt of “Low battery voltage. Please replace all batteries”. The meanings of different light colors 1. With 2 flashes in red: indicates the door is locking. 2. With 2 flashes in green: indicates the door is unlocking.
How to apply emergency power supply When the battery voltage is insufficient, and the door cannot be opened from the outside, you can power up the lock through the Micro USB interface by using a 5V power bank as an emergency power supply. After opening the door, please replace the batteries immediately. [RES] Button Emergency Power Supply Interface In case of a system crash and it’s impossible to open the door from outside, please press the [RES] button and then release it to reboot automatically.
Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license. This product has been manufactured by and is sold under the responsibility of Shenzhen Conex Intelligent Technology Co., Ltd. and Shenzhen Conex Intelligent Technology Co., Ltd. is the warrantor concerning this product. Version: 1.