User manual
Table Of Contents
- Contents
- Machine overview (Fig. A)
- Control panel (Fig. B)
- Introduction
- Before first use
- Brewing drinks
- Adjusting machine settings
- Removing and inserting the brew group
- Cleaning and maintenance
- AquaClean water filter
- Setting the water hardness
- Descaling procedure (30 min.)
- Ordering accessories
- Warning icons
- Troubleshooting
- Technical specifications
- Contenido
- Descripción general de la máquina (Fig. A)
- Panel de control (Fig. B)
- Introducción
- Antes del primer uso
- Preparación de bebidas
- Cambio de los ajustes de la máquina
- Retirada e inserción del grupo de preparación del café
- Limpieza y mantenimiento
- Filtro de agua AquaClean
- Establecer la dureza del agua
- Procedimiento de eliminación de los depósitos de cal (30 minutos)
- Pedido de accesorios
- Iconos de advertencia
- Solución de problemas
- Especificaciones técnicas
- Table des matières
- Vue d’ensemble de la machine (fig. A)
- Panneau de commande (fig. B)
- Introduction
- Avant la première utilisation
- Infusion de boissons
- Réglage des paramètres de la machine
- Retrait et insertion du groupe de percolation
- Nettoyage et entretien
- Filtre à eau AquaClean
- Réglage de la dureté de l’eau
- Procédure de détartrage (30 min.)
- Commande d'accessoires
- Icônes d’avertissement
- Résolution des problèmes
- Caractéristiques techniques
10
English
Adjusting grinder settings
You can change the coffee strength with the grind setting knob inside the bean container. The lower the
grind setting, the finer the coffee beans are ground and the stronger the coffee. There are 12 different grind
settings you can choose from.
The machine has been set up to get the best taste out of your coffee beans. Therefore we advise you not to
adjust the grind setting until you have brewed 100-150 cups (approx. 1 month of use).
You can only adjust the grind settings when the machine is grinding coffee beans. You need to brew 2 to
3 drinks before you can taste the full difference.
Do not turn the grind setting knob more than one notch at a time to prevent damage to the grinder.
1 Place a cup under the coffee dispensing spout.
2 Open the lid of the coffee bean hopper.
3 Tap the espresso icon and then press the start/stop button.
4 When the grinder starts grinding, press down the grind setting knob and turn it to the left or right. (Fig.
14)
Deactivate the beeps of the control panel
1 Press the on/off button to switch off the machine.
2 When the machine is switched off, tap and hold the coffee icon until the light in the icon goes on. The
start light starts flashing.
3 Tap the coffee icon again to deactivate the beeps of the control panel. The light in the coffee icon goes
out.
4 Press the start/stop button to confirm your choice.
5 Press the on/off button to switch on the machine again. The beeps of the control panel have now been
deactivated.
Note: If the light in the coffee icon does not go on after tapping and holding the icon, this means that the
beeps of the control panel already have been deactivated. To activate them again, tap the icon again and
confirm by pressing the start/stop button.
The beeps in the on/off button and in the start/stop button cannot be deactivated.
Removing and inserting the brew group
Go to www.philips.com/coffee-care for detailed video instructions on how to remove, insert and clean the
brew group.
Removing the brew group from the machine
1 Switch off the machine.
2 Remove the water tank and open the service door (Fig. 15).
3 Press the PUSH handle (Fig. 16) and pull at the grip of the brew group to remove it from the machine
(Fig. 17).
Reinserting the brew group
Before you slide the brew group back into the machine, make sure it is in the correct position.