User manual
Table Of Contents
- Contents
- Machine overview (Fig. A)
- Control panel (Fig. B)
- Introduction
- Before first use
- Brewing drinks
- Adjusting machine settings
- Removing and inserting the brew group
- Cleaning and maintenance
- AquaClean water filter
- Setting the water hardness
- Descaling procedure (30 min.)
- Ordering accessories
- Warning icons
- Troubleshooting
- Technical specifications
- Contenido
- Descripción general de la máquina (Fig. A)
- Panel de control (Fig. B)
- Introducción
- Antes del primer uso
- Preparación de bebidas
- Cambio de los ajustes de la máquina
- Retirada e inserción del grupo de preparación del café
- Limpieza y mantenimiento
- Filtro de agua AquaClean
- Establecer la dureza del agua
- Procedimiento de eliminación de los depósitos de cal (30 minutos)
- Pedido de accesorios
- Iconos de advertencia
- Solución de problemas
- Especificaciones técnicas
- Table des matières
- Vue d’ensemble de la machine (fig. A)
- Panneau de commande (fig. B)
- Introduction
- Avant la première utilisation
- Infusion de boissons
- Réglage des paramètres de la machine
- Retrait et insertion du groupe de percolation
- Nettoyage et entretien
- Filtre à eau AquaClean
- Réglage de la dureté de l’eau
- Procédure de détartrage (30 min.)
- Commande d'accessoires
- Icônes d’avertissement
- Résolution des problèmes
- Caractéristiques techniques
9
English
English
3 Place a cup under the coffee dispensing spout.
4 Select a single drink.
5 Press the aroma strength icon for 3 seconds (Fig. 8).
-
The pre-ground coffee light goes on and the start light starts pulsing.
6 Press the start/stop button.
7 To stop dispensing coffee before the machine is finished, press the start/stop button again.
With pre-ground coffee you can only brew one coffee at a time.
Pre-ground coffee is not a setting that is saved as a previous selected strength setting. Each time you
want to use pre-ground coffee, you need to press the aroma strength icon for 3 seconds.
When you select pre-ground coffee, you cannot select a different aroma strength.
Dispensing hot water
1 If attached, remove the milk frother.
2 Tap the hot water icon (Fig. 9).
-
The drink quantity lights go on and show the previous selected drink setting for hot water.
3 Adjust the hot water quantity to your preference by tapping the drink quantity icon (Fig. 3).
4 Press the start/stop button.
-
The light in the hot water icon flashes and hot water is dispensed from the hot water spout (Fig. 10).
5 To stop dispensing hot water before the machine is finished, press the start/stop button again.
Adjusting machine settings
Adjusting the stand-by time
1 Press the on/off button to switch off the machine.
2 When the machine is switched off: press and hold the Calc / Clean icon (Fig. 11) until the Calc / Clean
light and the Aroma strength lights go on (Fig. 12).
3 Tap the Aroma strength icon to select the required stand-by time: 15, 30, 60 or 180 minutes. Respectively
1, 2, 3 or 4 lights of the Aroma strength icon light up.
4 When you have finished setting the stand-by time, press the start/stop button. The machine switches off.
5 Press the on/off button to switch on the machine again.
Adjusting the coffee temperature
Machines without temperature icon
1 Press the on/off button to switch off the machine.
2 When the machine is switched off: press and hold the coffee quantity icon until the lights in this icon go
on (Fig. 13).
3 Tap the quantity icon to select the required temperature: normal, high or max.
-
Respectively 1, 2 or 3 lights are on.
4 When you have finished setting the coffee temperature, press the start/stop button.
5 Press the on/off button to switch on the machine again.
If you do not switch off the machine yourself, it will switch off automatically after some time.