User Manual
Table Of Contents
- Contents
- Machine overview (Fig. A)
- Control panel (Fig. B)
- Introduction
- Before first use
- Brewing drinks
- Adjusting machine settings
- Removing and inserting the brew group
- Cleaning and maintenance
- AquaClean water filter
- Setting the water hardness
- Descaling procedure (30 min.)
- Ordering accessories
- Troubleshooting
- Technical specifications
- Contenido
- Descripción general de la máquina (Fig. A)
- Panel de control (Fig. B)
- Introducción
- Antes del primer uso
- Preparación de bebidas
- Cambio de los ajustes de la máquina
- Retirada e inserción del grupo de preparación del café
- Limpieza y mantenimiento
- Filtro de agua AquaClean
- Establecer la dureza del agua
- Procedimiento de eliminación de los depósitos de cal (30 minutos)
- Pedido de accesorios
- Solución de problemas
- Especificaciones técnicas
- Table des matières
- Vue d’ensemble de la machine (fig. A)
- Panneau de commande (fig. B)
- Introduction
- Avant la première utilisation
- Infusion de boissons
- Étapes générales
- Personnalisation des boissons
- Préparation d’un café à partir de grains
- Préparation des boissons à base de lait avec le LatteGo (récipient à lait)
- Production de mousse de lait avec le mousseur à lait classique
- Infuser du café avec du café prémoulu
- Préparation du café glacé (certains modèles uniquement)
- Distribution d’eau chaude
- Réglage des paramètres de la machine
- Retrait et insertion du groupe de percolation
- Nettoyage et entretien
- Filtre à eau AquaClean
- Réglage de la dureté de l’eau
- Procédure de détartrage (30 min.)
- Commande d'accessoires
- Résolution des problèmes
- Caractéristiques techniques
10
English
Pre-ground coffee is not a setting that is saved as a previous selected strength setting. Each time you
want to use pre-ground coffee, you need to press the aroma strength icon for 3 seconds.
When you select pre-ground coffee, you cannot select a different aroma strength.
Brewing iced coffee (specific types only)
The coffee is brewed with warm water. Brew over ice cubes for optimal results.
1 Take a glass and fill it halfway with ice cubes.
2 Place the glass under the coffee dispensing spout.
3 Tap the iced coffee icon (Fig. 14).
-
The aroma strength and quantity lights go on.
-
You can now adjust the drink to your preferred taste.
We recommend using aroma strength 3.
4 Press the start/stop button.
5 To stop dispensing coffee before the machine is finished, press the start/stop button again.
6 For a special iced coffee treat, top it up with cold milk.
Dispensing hot water
1 If attached, remove LatteGo or the milk frother.
2 Tap the hot water icon (Fig. 15).
-
The drink quantity lights go on and show the previous selected drink setting for hot water.
3 Adjust the hot water quantity to your preference by tapping the drink quantity icon (Fig. 3).
4 Press the start/stop button.
-
The light in the hot water icon flashes and hot water is dispensed from the hot water spout (Fig. 16).
5 To stop dispensing hot water before the machine is finished, press the start/stop button again.
Adjusting machine settings
Adjusting the stand-by time
1 Press the on/off button to switch off the machine.
2 When the machine is switched off: press and hold the Calc / Clean icon (Fig. 17) until the Calc / Clean
light and the Aroma strength lights go on (Fig. 18).
3 Tap the Aroma strength icon to select the required stand-by time: 15, 30, 60 or 180 minutes. Respectively
1, 2, 3 or 4 lights of the Aroma strength icon light up.
4 When you have finished setting the stand-by time, press the start/stop button. The machine switches off.
5 Press the on/off button to switch on the machine again.
Programming the highest default setting of your drinks
The machine has 3 default settings for each drink: low, medium, high. You can only adjust the quantity of
the highest setting. The new quantity can be stored as soon as the start light starts to pulse.
Before you start programming the quantity of a milk drink, assemble LatteGo and pour milk in it.