FC8269 - FC8250
29
1 1 2 3 21 4 22 5 7 6 8 9 10 11 13 12 16 14 23 24 15 25 26 17 18 19 20
FC8269-FC8250 English 6 简体中文 11
English General description (Fig.
English 7 Before first use You can remove the stickers from the plastic storage container (specific types only). Preparing for use Hose 1 To connect the hose, push it into the appliance (1) and turn it clockwise (2) (Fig. 2). To disconnect the hose, turn it anticlockwise and pull it out of the appliance. Plastic tube (specific types only) 1 To connect the tube parts to each other, insert the narrow section into the wider section and turn a little. (Fig.
English 2 Press the on/off button on top of the appliance with your foot to switch on the appliance. -- If you want to pause for a moment, insert the ridge on the nozzle into the parking slot to park the tube in a convenient position (Fig. 10). Adjusting suction power You can adjust the suction power with: -- the suction power slide on the handgrip or (Fig. 11) -- the electronic suction power control on the vacuum cleaner (specific types only) (Fig. 12).
English 9 6 Remove the filter cylinder from the dust container (Fig. 21). 7 To clean the filter cylinder, tap against the side of a dustbin (Fig. 22). 8 Empty the dust container into a dustbin (Fig. 23). 9 Put the filter cylinder back into the dust container (Fig. 24). 10 Put the filter cylinder case back onto the filter cylinder (1) and turn it clockwise to fix it (2) (Fig. 25). 11 Reattach the lid of the dust container (1) and close it (‘click’) (2) (Fig. 26).
English Troubleshooting 1 The suction power is insufficient -- Perhaps the dust container is full. If necessary, empty the dust container. -- Perhaps the filters need to be cleaned or replaced. If necessary, clean or replace the filters. -- Perhaps the suction power slide on the handgrip is open. Close the slide. -- Perhaps the electronic suction power control (specific types only) has been set to a low setting. Set the control to a higher setting. -- Perhaps the nozzle, tube or hose is blocked up.
简体中文 11 一般说明 (图 1) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 滤芯罩 滤芯 集尘盒盖 集尘盒 软管连接孔 软管接口 顶部把手 电源线回卷按钮 通过电子吸力控制旋钮即可调整吸力(仅限于特定机型) 电源插头 开/关钮 摆放固定槽 HEPA 滤网(仅限特定型号) 过滤器栅格 微型滤网(仅限于特殊型号) 后轮 组合吸嘴 缝隙吸嘴 小号吸嘴(仅限于特定机型) 毛刷吸嘴(仅限于特定机型) 带握把和吸力控制滑块的软管 伸缩管(仅限于特定机型) 塑料硬管两端(仅限于特定机型) 前方握把 转轮 型号牌 注意事项 使用产品之前,请仔细阅读本用户手册,并妥善保管以供日后参 考。 -- 在将产品连接电源之前,请先检查产品所标电压与当地的供电电 压是否相符。 -- 如果插头、电源线或产品本身受损,请勿再使用本产品。 -- 如果产品的电源线损坏,为避免危险,必须由制造厂或其维修部 或厂方认可的专职人员来更换。 -- 请将产品放置在儿童接触不到的地方。 -- 切勿吸取水或其它液体。切勿吸取易燃物质,并且不要吸取未冷 却的
简体中文 -- 切勿在没有滤芯的情况下使用本产品。这会损坏马达并缩短产品 的使用寿命。 -- 如果集尘盒没有正确放置,则产品将无法运行。 电磁场 (EMF) 这款飞利浦产品符合关于电磁场 (EMF) 的相关标准。据目前的科学证明,如果正确使用并 按照本用户手册中的说明进行操作,本产品是安全的。 初次使用之前 您可以撕掉塑料存放箱上的不干胶标签(仅限于特定机型)。 使用准备 软管 1 要将软管连接,将软管推入吸尘器 (1) 并以顺时针方向旋转即可 (2)。 (图 2) 要将软管从吸尘器上拆下,请将管端逆时针方向转动,并拉出软管。 塑料硬管(仅限于特定机型) 1 要将硬管的两端相互连接,请将窄的部分插入宽的部分,同时稍加旋转。 (图 3) 2 要将硬管与软管的握把连接起来,应将窄的部分插入宽的部分并且稍微转一 下。 (图 4) -- 要断开硬管或硬管两端,请向外拉并且稍微转一下。 -- 请通过同样的方法来连接及拆卸吸嘴。 伸缩管(仅限于特定机型) 1 按伸缩管部件上的弹簧式锁定钮,将锁定钮滑入另一个管部件的开口。 2 将伸缩管与软管的握把连接起来。将窄的部分插入宽的部分并且稍微转一下。 --
简体中文 13 使用本产品 使用吸尘器 -- 您可以手握前方或顶部的把手提起吸尘器。 (图 9) 1 将电源线从产品中拉出,插入电源插座。 2 用脚按下产品上的 on/off(开/关)按钮来开启电源。 -- 如要暂停使用吸尘器,可通过将吸嘴上的夹片插入摆放固定槽以将硬管放妥。 (图 10) 调整吸力 您可以使用下列部件调节吸力: -- 握把上的吸力滑块或 (图 11) -- 吸尘器上的电子吸力控制旋钮(仅限于特定机型)。 (图 12) 更换 更换过滤网 更换过滤网前,切记拔下电器插头。 吸尘器配有微型滤网或 HEPA 滤网。 微型滤网(仅限于特殊型号) 每 6 个月更换一次微型滤网。 1 要取出滤网栅格,请逆时针方向转动 (1) 并拉出栅格 (2)。 (图 13) 2 从栅格中取出滤网架。 3 从滤网栅格上取下旧的滤网。 4 将新的滤网放在栅格上并使用滤网支架将其锁定到位。 (图 14) 5 将滤网栅格重新放入吸尘器 (1) 并顺时针转动 (2)。 (图 15) HEPA 滤网(仅限特定型号) 每 6 个月更换一次 HEPA 滤网。 1 要取出滤网栅格,请逆时针方向转动 (1) 并拉出栅格 (2)。 (
简体中文 1 从产品中拔出软管。 2 打开上盖。 (图 17) 3 从吸尘器上卸下集尘盒。 (图 18) 4 取下集尘盒的盒盖。 (图 19) 5 要取下滤芯罩,请逆时针旋转并将滤芯罩从集尘盒取出。 (图 20) 6 从集尘盒中取出滤芯。 (图 21) 7 要清洁滤芯,可以将滤芯在垃圾箱的一侧轻敲。 (图 22) 8 将集尘盒倒空至垃圾箱中。 (图 23) 9 将滤芯放回集尘盒中。 (图 24) 10 将滤芯罩重新放到滤芯上 (1) 并且顺时针转动以固定 (2)。 (图 25) 11 重新安放集尘盒盖 (1) 并将其锁闭(听到咔哒声)(2)。 (图 26) 12 把集尘盒放回吸尘器内。 (图 27) 13 将机罩关闭(听到咔哒声)。 (图 28) 存放 (图 29) 1 关闭吸尘器的电源,从插座中拔下电源插头。 2 按下电源线回卷按钮将电源线回卷到吸尘器中。 3 有两种方法存放本产品: (图 10) -- 将吸嘴上的夹片插入摆放固定槽,以将硬管放妥然后存放本产品。 -- 可以将产品及其附件存放在随附的储藏箱中。 4 要储存本产品,请查看用户手册开头的储存示意图。该图说明了如何在储藏箱或塑料 存放箱
简体中文 15 故障种类和处理方法 1 吸力不够 -- 可能集尘盒已满。 如有必要,应清空集尘盒。 -- 可能需要清洁或更换滤网。 如有必要,应清洁或更换滤网。 -- 可能握把上的吸力滑块已打开。 关闭滑块。 -- 可能电子吸力控制旋钮(仅限于特定机型)已设置为较低的档。 将控制旋钮设置为更高的档。 -- 可能吸嘴、硬管或软管阻塞。(图 31) -- 要清除阻塞物,请将阻塞的部分拆下,并将它以相反方向连接(尽可能离的远一 些)。打开吸尘器的电源,强迫气流反方向通过阻塞的部位。
2009/05/20
2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 2 1
22 23 24 25 26 27 28 30 31
4222.003.3346.