operation manual
Table Of Contents
- Introduction
- General description
- Remote control
- How your robot works
- Before first use
- Preparing for use
- Using your robot
- Cleaning and maintenance
- Replacement
- Troubleshooting
- Pengenalan
- Perihalan umum
- Unit kawalan jauh
- Bagaimana robot anda berfungsi
- Sebelum penggunaan pertama
- Membuat persediaan untuk guna
- Menggunakan robot anda
- Pembersihan dan penyelenggaraan
- Penggantian
- Penyelesai Masalah
- ข้อมูลเบื้องต้น
- คำอธิบายทั่วไป
- รีโมทคอนโทรล
- วิธีการทำงานของหุ่นยนต์
- ก่อนใช้งานครั้งแรก
- การเตรียมตัวก่อนใช้งาน
- การใช้หุ่นยนต์
- การทำความสะอาดและบำรุงรักษา
- การเปลี่ยนอะไหล่
- การแก้ปัญหา
- 说明
- 基本说明
- 遥控器
- 吸尘器如何工作
- 首次使用之前
- 使用准备
- 使用吸尘器
- 清洁和保养
- 更换
- 故障种类和处理方法
- 簡介
- 一般描述
- 遙控器
- 自動吸塵機器人運作方式
- 第一次使用前
- 使用前準備
- 使用自動吸塵機器人
- 清潔與維護
- 更換
- 疑難排解
- 소개
- 제품 정보
- 리모콘
- 로봇 청소기 작동 원리
- 처음 사용 전
- 사용 준비
- 로봇 청소기 사용
- 청소 및 유지관리
- 교체
- 문제 해결
Mopping with the robot
Types FC8796 and FC8794 come with a mopping attachment and a mopping pad for wet cleaning of
hard floors.
Attaching the mopping pad
1 Soak the mopping pad in water or wet the mopping pad under the tap. You can add a few drops of
a readily available floor cleaner that is suitable for your floor.
2 Squeeze the mopping pad thoroughly to ensure it is only damp instead of wet.
3 Attach the damp mopping pad to the mopping attachment by pushing the Velcro fasteners of the
mopping pad onto Velcro fasteners of the mopping attachment (Fig. 29).
4 Insert the attachment lugs of the mopping attachment into the two attachment holes located just
behind the wheels. Then press down until you hear a click (Fig. 30).
Cleaning floors with the mopping attachment
Note: To clean hard floors with the mopping attachment, you have to start the robot from a point in
the room you wish to clean. You cannot start the robot from its docking station with the mopping pad
attached.
1 Just press the start/stop button on the remote control to start the robot.
-
The robot continues mopping until its battery runs low and the robot stops.
Note: Detach the mopping pad and the mopping attachment before you send the robot to the
docking station with the docking button on the remote control or before you place the robot on the
docking station manually.
Detaching the mopping attachment
1 To detach the mopping attachment, press the tab (1) and pull up the mopping attachment to
remove it (2) (Fig. 31).
2 Pull the mopping pad off the mopping attachment.
3 To clean the mopping pad, wash it in the washing machine on a gentle cycle at a temperature of
60°C max.
Alarm signal
If the robot gets into trouble while cleaning (e.g., because a wheel jams or is no longer in contact with
the floor, or because a sensor can no longer detect the floor), you will hear a sound and the robot
stops. Press the start/stop button to switch the robot to standby mode and solve the problem that
causes the alarm signal, for instance by removing the obstacle that blocks the wheel, cleaning the
sensors, or picking up the robot and putting it down in a different place.
Cleaning and maintenance
Emptying and cleaning the dust container
Empty and clean the dust container when the start/stop button starts flashing.
1 Pull up the handle of the dust container lid and lift the dust container out of the dust container
compartment (Fig. 32).
2 Pull the tab on the side of the dust container to open the lid (Fig. 33).
3 Remove the filter unit from the dust container (Fig. 34).
4 Shake the dust container over a dustbin to empty it (Fig. 35).
10
English