operation manual
Table Of Contents
- Introduction
- General description
- Remote control
- How your robot works
- Before first use
- Preparing for use
- Using your robot
- Cleaning and maintenance
- Replacement
- Troubleshooting
- Pengenalan
- Perihalan umum
- Unit kawalan jauh
- Bagaimana robot anda berfungsi
- Sebelum penggunaan pertama
- Membuat persediaan untuk guna
- Menggunakan robot anda
- Pembersihan dan penyelenggaraan
- Penggantian
- Penyelesai Masalah
- ข้อมูลเบื้องต้น
- คำอธิบายทั่วไป
- รีโมทคอนโทรล
- วิธีการทำงานของหุ่นยนต์
- ก่อนใช้งานครั้งแรก
- การเตรียมตัวก่อนใช้งาน
- การใช้หุ่นยนต์
- การทำความสะอาดและบำรุงรักษา
- การเปลี่ยนอะไหล่
- การแก้ปัญหา
- 说明
- 基本说明
- 遥控器
- 吸尘器如何工作
- 首次使用之前
- 使用准备
- 使用吸尘器
- 清洁和保养
- 更换
- 故障种类和处理方法
- 簡介
- 一般描述
- 遙控器
- 自動吸塵機器人運作方式
- 第一次使用前
- 使用前準備
- 使用自動吸塵機器人
- 清潔與維護
- 更換
- 疑難排解
- 소개
- 제품 정보
- 리모콘
- 로봇 청소기 작동 원리
- 처음 사용 전
- 사용 준비
- 로봇 청소기 사용
- 청소 및 유지관리
- 교체
- 문제 해결
![](/manual/philips/fc8794-01/operation-manual-english-indonesian-korean-thai-chinese-chinese/images/img-14.png)
Problem Possible cause Solution
The robot is cleaning a floor
that reflects sunlight quite
strongly. This triggers the drop-
off sensors and causes the
robot to move in an unusual
pattern.
Close the curtains to block sunlight from
entering the room. You can also start
cleaning when the sunlight is less bright.
The rechargeable battery
can no longer be charged
or runs empty very fast.
The rechargeable battery has
reached the end of its life.
Have the rechargeable battery replaced
by a Philips service center (see
'Replacing the rechargeable battery').
The robot is moving in
circles.
The robot is in spot-cleaning
mode.
This is normal behavior. The spot-
cleaning mode can be activated when a
lot of dirt is detected on the floor for a
thorough clean. It is also part of the auto
cleaning mode. After approximately one
minute the robot resumes its normal
cleaning pattern. You can also stop the
spot-cleaning mode by selecting a
different cleaning mode on the remote
control.
You can also stop the spot-cleaning
mode by selecting a different cleaning
mode on the remote control.
The robot cannot find the
docking station.
There is not enough room for
the robot to navigate towards
the docking station.
Try to find another place for the docking
station (see 'Installing the docking
station').
The robot is still actively
searching.
Give the robot around 20 minutes to
return to the docking station.
The robot was not started from
the docking station.
If you want the robot to return to the
docking station after a cleaning run, start
it from the docking station.
14
English