operation manual
Table Of Contents
- Introduction
- General description
- Remote control
- How your robot works
- Before first use
- Preparing for use
- Using your robot
- Cleaning and maintenance
- Replacement
- Troubleshooting
- Pengenalan
- Perihalan umum
- Unit kawalan jauh
- Bagaimana robot anda berfungsi
- Sebelum penggunaan pertama
- Membuat persediaan untuk guna
- Menggunakan robot anda
- Pembersihan dan penyelenggaraan
- Penggantian
- Penyelesai Masalah
- ข้อมูลเบื้องต้น
- คำอธิบายทั่วไป
- รีโมทคอนโทรล
- วิธีการทำงานของหุ่นยนต์
- ก่อนใช้งานครั้งแรก
- การเตรียมตัวก่อนใช้งาน
- การใช้หุ่นยนต์
- การทำความสะอาดและบำรุงรักษา
- การเปลี่ยนอะไหล่
- การแก้ปัญหา
- 说明
- 基本说明
- 遥控器
- 吸尘器如何工作
- 首次使用之前
- 使用准备
- 使用吸尘器
- 清洁和保养
- 更换
- 故障种类和处理方法
- 簡介
- 一般描述
- 遙控器
- 自動吸塵機器人運作方式
- 第一次使用前
- 使用前準備
- 使用自動吸塵機器人
- 清潔與維護
- 更換
- 疑難排解
- 소개
- 제품 정보
- 리모콘
- 로봇 청소기 작동 원리
- 처음 사용 전
- 사용 준비
- 로봇 청소기 사용
- 청소 및 유지관리
- 교체
- 문제 해결
The remote control works on two AA batteries.
1 Push the tab (1) to unlock the battery compartment lid (2) and remove the battery compartment lid
(Fig. 9).
2 Insert two AA batteries (Fig. 10).
Note: Make sure the + and - poles point in the right direction.
3 To reattach the battery compartment lid, first insert the lug into the opening in the rim of the
compartment (1) and then push down the lid (2) until it locks with a click (Fig. 11). Now the remote
control is ready for use.
Preparing for use
Installing the docking station
1 Insert the small plug of the adapter into the socket on the docking station (1) and insert the adapter
into the wall socket (2) (Fig. 12).
2 Place the docking station on a horizontal, level floor against a wall.
Note: Make sure that there are no obstacles or height differences 150 cm in front, 30 cm to the right
and 100 cm to the left of the docking station (Fig. 13).
Charging
1 Place the robot on the plugged-in docking station (Fig. 14).
2 Press the start/stop button to activate the robot (Fig. 15).
3 The start/stop button starts flashing (Fig. 16).
4 When the rechargeable battery is fully charged, the start/stop button lights up continuously (Fig.
17).
Preparing the room for a cleaning run
-
Before you start the robot on its cleaning run, make sure that you remove all loose and fragile
objects from the floor (Fig. 18).
-
Remove all cables, wires and cords from the floor to prevent the robot from getting entangled in
them.
-
If there is a rug with tassels in the room you want the robot to clean, fold the tassels under the rug
to prevent the robot from getting stuck on the tassels and to prevent the rug from getting damaged
(Fig. 19).
Using your robot
Starting and stopping
1 Press the start/stop button on the remote control (Fig. 20).
2 The start/stop button on the robot lights up continuously and the robot starts cleaning (Fig. 21).
3 The robot cleans in auto-cleaning mode until its battery runs low. In auto cleaning mode, it follows
repeated sequences of random, wall-following and spiral movements.
4 When the battery runs low, the start/stop button starts flashing quickly and the robot starts
searching for the docking station to charge (Fig. 22).
8
English