GC1800 - GC1700 SERIES 1 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 MAX 2 18
Preparing for use Filling the water tank ENGLISH Introduction Congratulations on your purchase and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/welcome. A B C D E F G H I J K L General description (Fig.
6 Hold the iron over the sink and set the steam control to the Calc-Clean position x. (Fig. 12) 7 Pull the steam control slightly upwards and gently shake the iron until all water in the tank has been used up. , Steam and boiling water come out of the soleplate. Scale (if any) is flushed out. 8 After you have used the Calc-Clean function, press down the steam control while you turn it to position O. Problem Cause Solution The iron is plugged in but the soleplate is cold.
Bahasa Melayu Pengenalan Tahniah atas pembelian anda dan selamat datang ke Philips! Untuk mendapat manfaat sepenuhnya daripada sokongan yang ditawarkan oleh Philips, daftarkan produk anda di www.philips.com/welcome. A B C D E F G H I J K L Perihalan umum (Gamb.
Fungsi Pembersihan Kerak Gunakan fungsi Pembersihan Kerak sekali setiap dua minggu. Jika air di kawasan anda terlalu keras (iaitu serpihan keluar dari plat dasar semasa menyeterika), anda harus menggunakan fungsi Pembersihan Kerak dengan lebih kerap. 1 Tetapkan kawalan stim ke kedudukan O. 2 Tetapkan suhu tombol pada MAX. 3 Isikan tangki air sampai paras maksimum. Jangan tuang cuka atau agen penanggal kerak yang lain ke dalam tangki air. 4 Masukkan plag perkakas.
繁體中文 簡介 恭喜您購買本產品並歡迎加入飛利浦!請於 www. philips.
保固與服務 若您需要相關服務或資訊,或是有任何問題,請瀏 覽飛利浦網站,網址為 www.philips.
简体中文 产品简介 感谢您的惠顾,欢迎光临飞利浦!为了您能充分享 受飞利浦提供的支持,请注册您的产品,网址为 www.philips.com/welcome。 一般说明 (图 1) A B C D E F G H I J K L 喷雾嘴(仅限于特定型号) 加水口 蒸汽控制 O.
7 将蒸汽控制旋钮轻轻地向上拉,然后柔和地摇 动熨斗,直到所有的水耗尽。 , 蒸汽和沸水会从底板冲出。水垢(如果有的话) 也一并冲出。 问题 原因 解决方法 熨斗已经插好插 头,但底板仍是 凉的。 接触不良。 检查电源线、插头和电源插座。 温度转盘设在 MIN。 将温度转盘设定到所需温度。 水箱中水不 足。 将水箱注满水(见“使用准备”一 章)。 蒸汽控制旋钮 转到了 O 位。 将蒸汽控制旋钮设定到 l 或 ; 位 置(见“使用产品”一章)。 熨烫时水从底板 漏出。 熨斗不够热。 将温度转盘设定在一个适合蒸汽熨 烫的温度( 2 到最大)。将熨斗 竖立,直到温度指示灯熄灭后再开 始熨烫。 喷雾功能不起作 用(仅限特定型 号) 水箱中水不 足。 将水箱注满水(见“使用准备”一 章)。 在熨烫过程中底 板内冒出水垢和 杂质。 硬水在底板内 形成水垢。 使用一次或多次除垢功能(见“清洁 和保养”一章)。 自动关熄指示灯 闪烁(仅限于特 定型号)。 自动关熄功 能已启动( 见“功能”一 章)。 提起熨斗或轻轻移动以禁用自动关熄 功能。自动关熄指示灯熄灭。 当熨斗冷却或存