USER MANUAL 02 EN Read carefully before using the machine. Register your product and get support at www.philips.
IMPORTANT SAFEGUARDS When using electrical appliances, basic safety precautions should always be followed, including the following: 1. Read all instructions. 2. Do not touch hot surfaces. Use handles or knobs. 3. To protect against fire, electric shock and injury to persons do not immerse cord, plugs, or appliance in water or other liquid. 4. Close supervision is necessary when the appliance is used by or near children. 5. Unplug from outlet when not in use and before cleaning.
CAUTION This appliance is for household use only. Any servicing, other than cleaning and user maintenance, should be performed by an authorized service center. Do not immerse machine in water. To reduce the risk of fire or electric shock, do not disassemble the machine. There are no parts inside the machine serviceable by the user. Repair should be done by authorized service personnel only. 1. Check voltage to be sure that the voltage indicated on the nameplate corresponds with your voltage. 2.
2 ENGLISH Congratulations on your purchase of a Philips super automatic coffee machine with integrated milk carafe! To fully benefit from the support that Philips offers, register your product at www.philips.com/welcome. The machine is suitable for preparing espresso coffee using whole coffee beans, and it is supplied with a milk carafe so that you can brew a perfect cappuccino in a quick and easy way.
ENGLISH Adjusting the Coffee Dispensing Spout ..............................................................................................23 Adjusting the Coffee Length .............................................................................................................24 BREWING ESPRESSO AND LONG ESPRESSO .......................................................25 Brewing Espresso or Long Espresso Using Coffee Beans .....................................................................
4 ENGLISH IMPORTANT Safety Instructions This machine is equipped with safety devices. Nevertheless, read and follow the safety instructions carefully and only use the machine properly as described in these instructions to avoid accidental injury or damage due to improper use of the machine. Keep this user manual for future reference. The term WARNING and this icon warn against possible severe injuries, danger to life and/or damage to the machine.
ENGLISH • • • • • • • • • • • 5 - before cleaning the machine. Pull on the mains plug, not on the power cord. Do not touch the mains plug with wet hands. Do not use the machine if the mains plug, the power cord or the machine itself is damaged. Do not make any modifications to the machine or its power cord. Only have repairs carried out by a service centre authorised by Philips to avoid any hazard. The machine should not be used by children younger than 8 years old.
6 ENGLISH Cautions • The machine is for household use only. It is not intended for use in environments such as canteens, staff kitchens of shops, offices, factories or other work environments. • Always put the machine on a flat and stable surface. • Do not place the machine on hot surfaces, directly next to a hot oven, heater units or similar sources of heat. • Only put roasted coffee beans into the coffee bean hopper.
ENGLISH 7 Electromagnetic Fields This appliance complies with all the applicable standards and regulations relating to the exposure to electromagnetic fields. Disposal This symbol on a product indicates that the product is covered by EU Directive 2012/19/EU. Please inform yourself about the local separate collection system for electrical and electronic products. Follow local regulations and do not dispose of the product as household waste.
8 INSTALLATION Product Overview 1 2 3 5 6 7 8 9 10 19 11 4 12 14 13 20 21 15 16 17 18 22 31 24 25 26 27 28 29 30 23
ENGLISH 9 General Description 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31.
10 ENGLISH PREPARING FOR USE Machine Packaging The original packaging has been designed and constructed to protect the machine during transport. We recommend keeping the packaging material for possible future transport. Machine Installation 1 Remove the machine from the packaging. 2 For best use, it is recommended to: • • • Choose a safe, level surface where there will be no danger of overturning the machine or being injured.
ENGLISH 11 5 Rinse the water tank with fresh water. 6 Fill the water tank with fresh water up to the MAX level and reinsert it into the machine. Make sure it is fully inserted. Caution: Never fill the water tank with warm, hot, sparkling water or any other liquid, as this may cause damage to the water tank and the machine. 7 Lift the coffee bean hopper lid. 8 Slowly pour the coffee beans into the coffee bean hopper.
ENGLISH 12 Switch the power button to "I". The “ 13 Press the “ ” button flashes. ” button to turn on the machine. Note: By keeping the “ ” button pressed for more than 8 seconds, the machine enters the demo mode. To exit the demo, turn the machine off and on again using the power button. Yellow 12 14 The control panel indicates that the circuit must be primed.
ENGLISH 13 USING THE MACHINE FOR THE FIRST TIME When using the machine for the first time, the following activities need to happen: 1) The machine will prime the circuit; 2) The machine will perform an automatic rinse/self-cleaning cycle. 3) You need to perform a manual rinse cycle. Circuit Priming During this process, fresh water flows through the internal circuit of the machine and the machine warms up. This takes a few minutes.
ENGLISH Automatic Rinse/Self-Cleaning Cycle When warm-up has been completed, the machine automatically performs a rinse/self-cleaning cycle of the internal circuits with fresh water. This takes less than a minute. 6 Place a container under the coffee dispensing spout to catch the small Yellow amount of water which will be dispensed. 7 The machine performs an automatic rinse cycle. Wait for the cycle to finish automatically. Note: Brewing can be stopped by pressing the “ ” button.
ENGLISH 15 Green 2 Check that the machine shows this display. Green 3 Select the pre-ground coffee brewing function by pressing the “ ” button. The machine shows this display. Note: Do not add any pre-ground coffee into the compartment. 4 Press the “ ” button. The machine will start dispensing water from the coffee dispensing spout. 5 When dispensing has finished, empty the container. Repeat the operations from step 1 to step 4 twice, then continue with step 6.
ENGLISH 8 Press the “ ” button to start dispensing hot water. Green 9 This icon is displayed. The machine reminds you to install the water dispensing spout. Check that the water dispensing spout is correctly installed. Press “ ” to confirm. The machine will start dispensing hot water. Red 10 Dispense water until the no water icon appears. Note: The manual rinse cycle can be stopped by pressing the “ ” button. 11 At the end of this operation, fill the water tank again up to the MAX Green 16 level.
ENGLISH 17 MEASURING AND PROGRAMMING WATER HARDNESS Water hardness measuring is very important in order to define the descaling frequency and to install the “INTENZA+” water filter (for more details on the water filter, see next chapter). To measure water hardness, follow the steps below: 1 Immerse the water hardness test strip (supplied with the machine) in water for 1 second. Note: The test strip can only be used for one single measurement. 2 Wait for one minute.
ENGLISH Yellow 5 Press the “ ” button to increase the value and the “ decrease the value. 6 Press the “ ” button to ” button to confirm the setting. 7 Press the “ Green 18 ” button to exit the programming MENU. The machine shows this display and is ready for brewing. "INTENZA+" WATER FILTER We recommend you to install the “INTENZA+” water filter as this prevents limescale build-up in your machine and preserves a more intense aroma of your coffee.
ENGLISH 19 3 Set the “INTENZA+” water filter according to the measurements performed (see previous chapter) and indicated on the base of the filter: A = soft water – equals 1 or 2 on the test strip B = hard water (standard) – equals 3 on the test strip C = very hard water – equals 4 on the test strip 4 Put the “INTENZA+” water filter into the empty water tank. Press it down until it cannot move any further. 5 Fill the water tank with fresh water and put it into the machine.
ENGLISH Replacing the “INTENZA+” Water Filter Yellow Yellow Yellow When the “INTENZA+” water filter needs to be replaced with a new one, this icon is displayed. 1 Replace the “INTENZA+” water filter as described in the previous chapter. 2 Press the “ ” button and scroll through the options by pressing the “ button until this icon is displayed. 3 Select the “RESET” option. Press the “ ” button to confirm. Green 4 Press the “ ” button to exit.
ENGLISH 21 ADJUSTMENTS The machine allows for certain adjustments so that you can enhance the quality and taste of your coffee. Saeco Adapting System Coffee is a natural product and its characteristics may change according to its origin, blend and roast. The machine is equipped with a self-adjusting system that allows the use of all types of coffee beans available on the market, except for raw, caramelized and flavoured coffee beans.
ENGLISH 2 While the machine grinds coffee, press and turn the grinder adjustment knob placed inside the coffee bean hopper one notch at a time. Use the special coffee grinder adjustment key supplied. You will taste the difference after brewing 2-3 cups of coffee. 3 The reference marks inside the coffee bean hopper indicate the grind 2 Adjusting the Aroma (Coffee Strength) Choose your favourite coffee blend and adjust the amount of coffee to be ground according to your personal taste.
ENGLISH 23 Adjusting the Coffee Dispensing Spout The height of the dispensing spout can be adjusted to better fit the dimensions of the cups that you wish to use. Move the dispensing spout up or down with your fingers to adjust its height as shown in the figure. The recommended positions are: For the use of small cups; For the use of large cups. Two cups can also be placed under the dispensing spout to brew two cups of espresso or long espresso at the same time.
ENGLISH Adjusting the Coffee Length The machine allows you to adjust the amount of brewed coffee according to your taste and the size of your cups. Each time the “ ” or “ ” button is pressed, the machine brews a pre-set amount of coffee. Each button may be individually programmed for a specific brew setting. 1 Place a cup under the dispensing spout. ” button pressed until the “MEMO” icon appears on the display to program an espresso, or do the same with the “ ” button to program a long espresso.
ENGLISH 25 BREWING ESPRESSO AND LONG ESPRESSO Before brewing coffee, make sure that there are no warnings shown on the control panel, and that the water tank and coffee bean hopper are filled. Brewing Espresso or Long Espresso Using Coffee Beans 1 Place 1 or 2 cups under the dispensing spout. 2 To brew an espresso or a long espresso, press the “ ” button to select the desired aroma. Green Green 3 Press the “ ” button for an espresso or the “ ” button for a long espresso.
ENGLISH Brewing Espresso or Long Espresso Using Pre-Ground Coffee This function allows you to use pre-ground coffee. With the pre-ground coffee function you can only brew one coffee at a time. Green 26 1 Press the “ ” button to select the pre-ground coffee function. 2 Lift the pre-ground coffee compartment lid and add one level measuring scoop of pre-ground coffee. Use only the measuring scoop supplied with the machine. Then close the pre-ground coffee compartment lid.
ENGLISH 27 MILK CARAFE This chapter explains how to use the milk carafe to prepare a cappuccino or to froth milk. Note: Before using the milk carafe, clean it thoroughly as described in the “Cleaning and Maintenance” chapter. We recommend that you fill the carafe with cold (~5°C / 41°F) milk with a protein content of at least 3% to ensure optimum results when preparing a cappuccino. Whole milk, skimmed milk, soy milk or lactose-free milk may be used depending on individual taste.
28 ENGLISH Inserting the Milk Carafe 1 If installed, remove the water dispensing spout as shown in the figure: - Press the two buttons on the side to unlock it and lift it slightly; Pull the water dispensing spout to remove it. 1 2 2 Slightly tilt the milk carafe. Insert it all the way into the guides of the machine. 3 Push the carafe towards the bottom while rotating it at the same time, until it is locked onto the drip tray. Do not force the carafe while inserting it.
ENGLISH 29 Emptying the Milk Carafe 1 A B 1 Press one of the release buttons to remove the top of the carafe as shown in the figures (A or B). 1 2 Lift the top of the carafe. Empty the milk carafe and clean it properly. Note: After each use, clean the milk carafe as described in the “Cleaning and Maintenance” chapter.
30 ENGLISH BREWING A CAPPUCCINO Warning: Danger of burning! Dispensing may be preceded by jets of milk and steam. Danger of burning! Wait until the end of the cycle before removing the milk carafe. 1 Fill the carafe with milk. The milk level must be between the minimum (MIN) and maximum (MAX) level indicators shown on the milk carafe. Note: Use cold (~5 °C / 41°F) milk with a protein content of at least 3% to ensure optimum results when preparing a cappuccino.
ENGLISH 31 ” button to start dispensing. 6 The machine reminds you to insert the carafe and pull out the carafe dispensing spout by showing the following icons. Green Green Green 5 Press the “ Green 7 This icon is displayed during the preheating time required by the machine. Green 8 When this icon is shown, the machine dispenses milk. Dispensing can be stopped by pressing the “ ” button. Green 9 Once frothed milk has been dispensed, the machine brews coffee.
32 ENGLISH 10 Insert the carafe dispensing spout back by sliding it up to the “ ” icon. Note: After using the milk carafe, clean it as described in the "Cleaning and Maintenance" chapter. You can prepare a cappuccino with pre-ground coffee. Press the “ ” button to select pre-ground coffee and pour pre-ground coffee into the compartment. Adjusting the Cappuccino Length Each time the “ ” button is pressed, the machine dispenses a pre-set quantity of cappuccino into the cup.
4 The machine reminds you to insert the carafe and pull out the carafe dispensing spout by showing the following icons. Green Green Green ENGLISH 33 Green 5 This icon is displayed during the preheating time required by the machine. frothed milk into the cup. When the desired quantity of frothed milk is reached, press the “ ” button. Green Green 6 When the machine shows this icon, the machine starts dispensing 7 Once frothed milk has been dispensed, the machine starts brewing Green coffee.
34 ENGLISH FROTHING MILK Warning: Danger of burning! Dispensing may be preceded by jets of milk and steam. Danger of burning! Wait until the end of the cycle before removing the milk carafe. 1 Fill the carafe with milk. The milk level must be between the minimum (MIN) and maximum (MAX) level indicators shown on the milk carafe. Note: Use cold (~5 °C / 41°F) milk with a protein content of at least 3% to ensure optimum results when preparing a cappuccino.
ENGLISH 35 ” button. The machine shows this display. 6 Press the “ ” button to select frothed milk. 7 The machine reminds you to insert the carafe and pull out the carafe dispensing spout by showing the following icons. Green Green Green Green 5 Press the “ Green 8 This icon is displayed during the preheating time required by the machine. Green 9 The machine dispenses a predefined quantity of frothed milk into the cup. Dispensing can be stopped by pressing the “ ” button.
ENGLISH 10 Insert the carafe dispensing spout back by sliding it up to the “ ” icon. Note: After using the milk carafe, clean it as described in the "Cleaning and Maintenance" chapter. Adjusting the Frothed Milk Length Each time this function is selected, the machine dispenses a preset amount of frothed milk into the cup. The machine allows you to adjust the amount of frothed milk according to your taste and the size of your cups. 1 Fill the carafe with milk and place it into the machine.
ENGLISH 37 4 Press and hold the “ 5 The machine reminds you to insert the carafe and pull out the carafe dispensing spout by showing the following icons. Green Green Green ” button to select frothed milk until the sequence described in step 5 is displayed. Then release the button. The machine is now in programming mode. Green 6 This icon is displayed during the preheating time required by the machine. Green Green 7 When the desired amount of frothed milk is reached, press the “ ” button.
ENGLISH DISPENSING HOT WATER Warning: Danger of burning! Dispensing may be preceded by small jets of hot water and steam. Danger of burning! Wait until the end of the cycle before removing the water dispensing spout. 1 Slightly tilt the water dispensing spout and insert it all the way in into the guides of the machine. 2 Push the water dispensing spout towards the bottom while rotating it at the same time, until it is locked in the machine as shown in the figure.
ENGLISH 39 5 Press the “ ” button to start dispensing. Green 6 This icon is displayed. The machine reminds you to install the water dispensing spout. Check that the water dispensing spout is correctly installed. Press “ ” to confirm. The machine will start dispensing hot water. Green 7 This icon is displayed during the preheating time required by the machine. Green 8 Dispense the desired amount of hot water. To stop dispensing hot water, press the " " button.
40 ENGLISH CLEANING AND MAINTENANCE Daily Cleaning of the Machine Caution: Timely cleaning and maintenance of your machine is very important as it prolongs the life of your machine. Your machine is continuously exposed to moisture, coffee and limescale! The activities you need to perform and their frequency are described in detail in this chapter. Not doing this will ultimately make your machine stop working properly. This repair is NOT covered by your warranty.
ENGLISH 41 4 Insert the coffee grounds drawer back into the drip tray and place the drip tray back into the machine. 1 2 Note: Empty the drip tray and coffee grounds drawer also when the full drip tray indicator is raised. Note: Other maintenance operations can only be carried out when the machine is turned off and unplugged. Cleaning of the Water Tank 1 Remove the small white filter or the “INTENZA+” water filter (if installed) from the water tank and wash it with fresh water.
ENGLISH 42 Daily Cleaning of the Milk Carafe It is important that you clean the milk carafe daily or after each use as it preserves hygiene and ensures perfect frothed milk consistency. Warning: Danger of burning! Dispensing may be preceded by small jets of hot water and steam. Danger of burning! Wait until the end of the cycle before removing the milk carafe. 1 A B 1 Press one of the release buttons to remove the top of the carafe as shown in the figures (A or B).
ENGLISH 43 4 Remove the lid and fill the milk carafe up to the MAX level with fresh water. 5 Put the lid back onto the milk carafe. Insert the carafe into the machine. 6 Pull out the carafe dispensing spout to the right up to the “ 7 Place a container under the dispensing spout. ” icon.
ENGLISH ” button. The machine shows this display. 9 Press the “ ” button to select frothed milk. 10 The machine reminds you to insert the carafe and pull out the carafe dispensing spout by showing the following icons. Green Green Green Green 8 Press the “ 11 This icon is displayed during the preheating time required by the Green 44 machine.
ENGLISH 45 Green 12 Once the machine stops dispensing water, washing is finished. 13 Insert the carafe dispensing spout back by sliding it up to the “ ” icon. Remove the milk carafe and empty it. Weekly Cleaning of the Machine 1 Clean the seat of the drip tray. Weekly Cleaning of the Milk Carafe The weekly cleaning is more thorough since all milk residues are removed from the dispensing spout.
ENGLISH 46 2 Remove the lid. 3 Lift the dispensing spout to remove it from the top of the carafe. The carafe dispensing spout is made up of six parts that must be disassembled. Each part is indicated by a capital letter (A, B, C, D, E, F), as shown in the figures below. 4 Remove the suction tube with the fitting (A) from the milk frother. A 5 Remove the fitting (B) from the suction tube.
ENGLISH 47 7 Remove the milk frothing device (D) from the support (E). D E 8 Remove the fitting (F) from the milk frothing device by pulling it outwards. F 9 Clean all the parts thoroughly with lukewarm water. Note: You can also clean individual parts in the dishwasher. 10 Insert the fitting (F) into the milk frothing device by pressing it up to its limit. F 11 Insert the milk frothing device (D) into the support (E).
ENGLISH 48 12 Attach the top (C) to the carafe dispensing spout. C 13 Insert the fitting (B) into the suction tube. B 14 Insert the suction tube with the fitting (A) into the milk frother. A 15 Insert the dispensing spout into the top part of the carafe.
ENGLISH 49 A B 16 If you cannot install the dispensing spout at the top of the carafe, the pin is in the wrong position (B). Before installing the dispensing spout, manually push the pin to the (A) position. 17 Insert the lid. 18 Attach the top of the milk carafe, ensuring it is locked into place.
50 ENGLISH Weekly Cleaning of the Brew Group Clean the brew group at least once a week. 1 Turn off the machine by pressing the “ ” button. Wait until the “ button flashes and unplug the power cord. ” 2 Raise the coffee dispensing spout and remove the drip tray and coffee grounds drawer by pressing the side buttons. 1 2 3 2 3 Open the service door. 4 To remove the brew group, press the «PUSH» button and pull it by the handle. Pull it out horizontally without turning it.
ENGLISH 51 5 Thoroughly clean the coffee duct outlet with the special cleaning tool supplied with the machine or with a spoon handle. Make sure that the cleaning tool is inserted as shown in the figure. 6 Remove the coffee residues drawer and wash it thoroughly. 7 Thoroughly wash the brew group with fresh water and carefully clean the upper filter. Caution: Do not use detergent or soap to clean the brew group. 8 Let the brew group air-dry thoroughly.
52 ENGLISH 11 Gently pull down the lever until it is in contact with the brew group base and the two reference marks on the side of the brew group match. 12 Press the “PUSH” button firmly. 13 Make sure that the hook which locks the brew group is in the correct position. If it is still in the downward position, push it upward until it locks correctly into place. 14 Insert the coffee residues drawer into its seat and ensure that it is correctly in place.
ENGLISH 53 15 Insert the brew group back into its seat until it locks into place without pressing the “PUSH” button. 16 Insert the coffee grounds drawer with the drip tray back into the machine and close the service door. Monthly Cleaning of the Milk Carafe For the monthly cleaning cycle, we recommend using the “Saeco Milk Circuit Cleaner” to keep the entire circuit clean of milk residues. The “Saeco Milk Circuit Cleaner” can be purchased separately.
ENGLISH 1 Fill the milk carafe with water up to the maximum level (MAX). 2 Pour the milk cleaner bag into the milk carafe and let it dissolve completely. 3 Insert the carafe into the machine. Pull out the carafe dispensing spout to the right up to the “ ” icon. 4 Place a container under the dispensing spout. 5 Press the “ Green 54 ” button. The machine shows this display.
ENGLISH 55 ” button to select frothed milk. 7 The machine reminds you to insert the carafe and pull out the carafe dispensing spout by showing the following icons. Green Green Green 6 Press the “ Green 8 This icon is displayed during the preheating time required by the machine. Green 9 Once the machine stops dispensing water, repeat steps 5 - 8 until the carafe is emptied. Warning: Never drink the solution dispensed during this step.
ENGLISH 11 Remove the milk carafe and the container from the machine. 12 Rinse and fill the milk carafe with fresh water up to the MAX level. 13 Insert the milk carafe into the machine. Pull out the carafe dispensing ” icon. Place a container under the spout to the right up to the “ dispensing spout to start the rinse cycle. 14 Press the “ ” button. The machine shows this display. 15 Press the “ ” button to select frothed milk.
16 The machine reminds you to insert the carafe and pull out the carafe dispensing spout by showing the following icons. Green Green Green ENGLISH 57 Green 17 This icon is displayed during the preheating time required by the machine. Green 18 Once the machine stops dispensing water, repeat steps 14 - 16 until the carafe is emptied. 19 Remove the milk carafe and the container from the machine. Repeat steps 11 - 16 one more time.
58 ENGLISH Monthly Lubrication of the Brew Group Lubricate the brew group after approximately 500 cups of coffee or once a month. The grease to lubricate the brew group can be purchased separately. For further details, please refer to the maintenance products page in this user manual. Caution: Before lubricating the brew group, clean it with fresh water and let it dry as described in the “Weekly Cleaning of the Brew Group” chapter. 1 Apply the grease evenly on both side guides.
ENGLISH 59 3 Insert the brew group into its seat until it locks into place (see the “Weekly Cleaning of the Brew Group” chapter). 4 Close the service door and insert the drip tray and coffee grounds drawer. Monthly Cleaning of the Brew Group with “Coffee Oil Remover” Besides weekly cleaning, we recommend running the cleaning cycle with “Coffee Oil Remover” after approximately 500 cups of coffee or once a month. This operation completes the maintenance process for the brew group.
ENGLISH 3 Put a “Coffee Oil Remover” tablet in the pre-ground coffee compartment. 4 Press the “ Green 60 ” button to select the pre-ground coffee function without adding ground coffee into the compartment. 5 Press the “ ” button to start the coffee brewing cycle. 6 Wait until the machine has dispensed half a cup of water. 7 Switch the power button on the back of the machine to “0”. 8 Let the solution take effect for about 15 minutes. Make sure you discard the dispensed water.
ENGLISH 61 11 Wash the brew group thoroughly with fresh water. 12 After rinsing the brew group, insert it back into its seat until it locks into place (see the “Weekly Cleaning of the Brew Group” chapter). Insert the drip tray and the coffee grounds drawer. Close the service door. 13 Press the “ Green ” button to select the pre-ground coffee function without adding any pre-ground coffee into the compartment. 14 Press the “ ” button to start the coffee brewing cycle. 15 Repeat steps 13 to 14 twice.
ENGLISH Monthly Cleaning of the Coffee Bean Hopper Clean the coffee bean hopper once a month when it is empty with a damp cloth to remove coffee oil. Then refill it with coffee beans. DESCALING When the “CALC CLEAN” icon is displayed, you need to descale the machine. Yellow 62 The descaling cycle takes approx. 30 minutes. Caution: Not doing this will ultimately make your machine stop working properly. In this case, repair is NOT covered by warranty. Warning: Use the Saeco descaling solution only.
ENGLISH 63 Preparation Phase To perform the descaling cycle, follow the steps below. Before descaling: 1 1 - Raise the coffee dispensing spout; 2 - Press the side buttons; 3 - Remove and empty the drip tray and the coffee grounds drawer, then place them back. 1 3 2 2 Fill the milk carafe with water up to the MIN level and insert it into the Yellow machine. 3 Press the “ ” button until this display is shown. 4 Press the “ ” button to start the descaling process. " button to quit.
ENGLISH 6 Remove the “INTENZA+” water filter (if installed) from the water tank and replace it with the small white original one. 7 Pour all the descaling solution into the water tank. Then fill the water tank with fresh water up to the CALC CLEAN level. CALC CLEAN 8 Put the water tank back into the machine. 9 Pull out the carafe dispensing spout to the right up to the “ ” icon. Place a large container (1.5 l) under both the carafe dispensing spout and the coffee dispensing spout.
Yellow ENGLISH 65 Note: The descaling cycle may be paused by pressing the “ ” button. To resume the cycle, press the “ ” button again. This allows you to empty the container or to leave the machine unattended for a short time. Red 12 When this icon is displayed, the water tank is empty. 13 Remove the water tank, rinse it and fill it with fresh water up to the CALC CLEAN level. Put it back into the machine. 14 Remove and empty the container and the milk carafe.
ENGLISH 16 Fill the milk carafe with water up to the MIN level and insert it into the machine. Pull out the carafe dispensing spout to the right up to the " " icon. 17 Place a large container (1.5 l) under both the carafe dispensing spout and the coffee dispensing spout. Rinse Phase ” button to start the rinse cycle. Yellow 18 Press the “ Note: The rinse cycle may be paused by pressing the “ ” button. To resume the cycle, press the “ ” button again.
ENGLISH 67 21 Remove the container. Disassemble and wash the milk carafe as described in the “Weekly Cleaning of the Milk Carafe” chapter. 22 Remove the small white filter and replace the INTENZA+ water filter (if installed) in the water tank. Rinse it and fill it with fresh water up to the CALC CLEAN level. Put it back into the machine. 23 1 - Raise the coffee dispensing spout; 2 - Press the side buttons; 3 - Remove and empty the drip tray, then place it back.
68 ENGLISH Interruption of the Descaling Cycle Once the descaling cycle has started, it must be completed; do not turn off the machine mid-cycle. If the machine stops, you can quit the cycle by pressing the on/off button. If this occurs, or in the event of power failure or accidental disconnection of the power cord, empty and rinse carefully the water tank, then fill it up to the CALC CLEAN level. Follow the instructions provided in the "Manual Rinse Cycle" chapter before brewing any beverage.
ENGLISH 69 PROGRAMMING You can customise the machine functions via the programming menu. Yellow Yellow Yellow Yellow Yellow Yellow The Following Settings Can Be Adjusted Coffee Temperature This function allows you to adjust the coffee brewing temperature. Timer (stand-by) This function allows you to adjust the time taken for the machine to go into stand-by mode after the last brewing. Contrast This function allows you to adjust the contrast of the display to better view the messages.
Yellow ENGLISH Factory Settings This function allows you to reset all factory values. How to Program the Machine Green This example shows how to program the display contrast. Proceed in the same way to program the other functions. The programming menu can only be accessed when the machine is on and shows this display. Yellow 1 Press the “ ” button to access programming. 2 The main screen will be displayed. 3 Press the “ ” button to scroll the options until the display contrast function is shown.
ENGLISH 71 4 Press the “ ” and “ ” buttons to increase or decrease the value of the Yellow function. 5 Once the value has been changed, the “OK” message appears. Press the “ ” button to confirm the change. 6 Press the “ ” button to exit programming. Note: The machine automatically exits programming mode if no button is pressed for 3 minutes. The values that have been changed but not confirmed will not be saved.
72 ENGLISH MEANING OF THE DISPLAY ICONS This machine is equipped with a colour-coded system to make the user’s understanding of the display signals easier. The icons are colour-coded according to the traffic light principle. Ready Signals (Green Colour) The machine is ready to brew products. The machine is ready to brew pre-ground coffee. The machine is brewing one cup of espresso. The machine is brewing two cups of espresso. The machine is brewing one cup of long espresso.
ENGLISH 73 Ready Signals (Green Colour) Frothed milk or hot water selection. Water dispensing. Frothed milk dispensing. The machine is frothing milk for a cappuccino. The machine is brewing coffee for a cappuccino. The machine is programming the amount of milk to be dispensed for a cappuccino. The machine is programming the amount of coffee to be brewed for a cappuccino. The machine is programming the amount of milk to be dispensed for frothed milk.
74 ENGLISH Ready Signals (Green Colour) Insert the water dispensing spout and press the “ dispensing. Press “ ” to exit. ” button to start The machine is warming up to dispense beverages. Warning Signals (Yellow Colour) The machine is warming up. The machine is performing the rinse cycle. Wait until the machine has completed the cycle. The machine needs the "INTENZA+" water filter to be replaced. The brew group is being reset due to machine reset.
ENGLISH 75 Warning Signals (Red Colour) Completely insert the drip tray with the coffee grounds drawer into the machine and close the service door. Fill the coffee bean hopper. The brew group must be inserted into the machine. Empty the coffee grounds drawer. Wait 5 seconds before reinserting it. Fill the water tank. Exx The machine is out of order. The error code is displayed in the right bottom corner. For error codes 1 -3 - 4 - 5, please refer to the "Troubleshooting" chapter.
76 ENGLISH TROUBLESHOOTING This chapter summarizes the most common problems you could encounter with your machine. If you are unable to solve the problem with the information below, visit www.philips.com/support for a list of frequently asked questions or contact the Philips hotline in your country. Contact details can be found in the warranty booklet supplied separately or at www.philips.com/support. Machine actions Causes Solutions Error Code 1 Coffee grinder blocked. Coffee outlet duct clogged.
ENGLISH 77 Machine actions The machine does not turn on. Causes The machine is not connected to the electric network, or the power button is in the “O” position. Solutions Connect the machine to the electric network and turn the power button to the “I” position. The machine is in demo mode. The “ ” button was pressed and held for more than 8 seconds. Turn the machine off and back on using the power button. The drip tray gets filled although no water is drained.
78 ENGLISH Machine actions Causes Coffee is not brewed, is brewed The coffee grind is too fine. slowly or only a few drops are brewed (see note). The circuit is not primed. The brew group is dirty. The dispensing spout is dirty. The machine circuit is clogged by limescale. Coffee leaks out of the dispens- The dispensing spout is clogged. ing spout. No hot water is dispensed. The circuit is not primed. Frothed milk is too cold. The milk is not frothed or will not come out.
ENGLISH 79 ENERGY SAVING Stand-by The Philips super automatic espresso coffee machine is designed for energy saving, as proven by the Class A energy label. After 15 minutes of inactivity, the machine turns off automatically (unless a different stand-by time has been programmed). If a product has been brewed, the machine performs a rinse cycle. In stand-by mode, the energy consumption is below 1Wh. To turn on the machine, press the “ ” button (if the power button on the back of the machine is set to “I”).
80 ENGLISH FACTORY SETTINGS Beverage Adjustment Beverages Predefined quantity Aroma Strength Adjustable: 40 ml 3 20 ml - 230 ml 120 ml 3 20 ml - 230 ml 50 ml / 34 sec milk 3 20 - 230 ml / 10 - 75 sec Espresso Long espresso Cappuccino (Coffee/milk) Frothed milk 34 sec 10-75 sec Note: the values provided may vary. WARRANTY AND SERVICE Warranty For detailed information on your warranty and related conditions, please read the warranty booklet supplied separately.
ENGLISH 81 ORDERING MAINTENANCE PRODUCTS For cleaning and descaling, use Philips maintenance products only. You can purchase these products at the Philips online shop (if available in your country) at www.shop.philips.com/service, from your local dealer or at authorised service centres. If you have any difficulties obtaining maintenance products for your machine, please contact the Philips hotline in your country. Contact details can be found in the warranty booklet packed separately or at www.philips.
82 ENGLISH - Coffee Oil Remover CA6704 - Milk Circuit Cleaner: CA6705 - Maintenance Kit CA6706
Rev.00 del 30-04-15 02 EN 02 The manufacturer reserves the right to make changes without prior notice. www.philips.
