English 02 USER MANUAL Type HD8762, HD8780, HD8862, HD8865 02 EN Read carefully before using the machine. Register your product and get support at www.saeco.
IMPORTANT SAFEGUARDS When using electrical appliances, basic safety precautions should always be followed, including the following: 1. Read all instructions. 2. Do not touch hot surfaces. Use handles or knobs. 3. To protect against fire, electric shock and injury to persons do not immerse cord, plugs, or appliance in water or other liquid. 4. Close supervision is necessary when the appliance is used by or near children. 5. Unplug from outlet when not in use and before cleaning.
CAUTION This appliance is for household use only. Any servicing, other than cleaning and user maintenance, should be performed by an authorized service center. Do not immerse machine in water. To reduce the risk of fire or electric shock, do not disassemble the machine. There are no parts inside the machine serviceable by the user. Repair should be done by authorized service personnel only. 1. Check voltage to be sure that the voltage indicated on the nameplate corresponds with your voltage. 2.
2 ENGLISH Congratulations on your purchase of a Saeco Minuto Automatic Milk Frother fully automatic coffee machine! To fully benefit from the support that Saeco offers, please register your product at www.saeco.com/welcome. The machine is made for preparing espresso coffee using whole coffee beans and for dispensing steam and hot water. In this user manual you will find all the information you need to install, use, clean and descale your machine.
ENGLISH CONTENTS IMPORTANT..................................................................................................... 4 Safety Instructions ....................................................................................................................................4 Warnings...................................................................................................................................................4 Cautions ..............................................................
4 ENGLISH IMPORTANT Safety Instructions This machine is equipped with safety devices. Nevertheless, read and follow the safety instructions carefully and only use the machine properly as described in these instructions to avoid accidental injury or damage due to improper use of the machine. Keep this user manual for future reference. The term WARNING and this icon warn against possible severe injuries, danger to life and/or damage to the machine.
ENGLISH • • • • • • • • • • • 5 - if the machine will not be used for a long time; - before cleaning the machine. Pull on the mains plug, not on the power cord. Do not touch the mains plug with wet hands. Do not use the machine if the mains plug, the power cord or the machine itself is damaged. Do not make any modifications to the machine or its power cord. Only have repairs carried out by a service centre authorised by Philips to avoid any hazard.
6 ENGLISH Cautions • The machine is for household use only. It is not intended for use in environments such as canteens, staff kitchens of shops, offices, factories or other work environments. • Always put the machine on a flat and stable surface. • Do not place the machine on hot surfaces, directly next to a hot oven, heater units or similar sources of heat. • Only put roasted coffee beans into the coffee bean hopper.
ENGLISH 7 Electromagnetic Fields This appliance complies with all the applicable standards and regulations relating to the exposure to electromagnetic fields. Disposal This symbol on a product indicates that the product is covered by EU Directive 2012/19/EU. Please inform yourself about the local separate collection system for electrical and electronic products. Follow local regulations and do not dispose of the product as household waste.
8 INSTALLATION Product Overview 1 2 3 5 6 7 14 8 9 10 15 11 4 12 32 13 18 21 16 34 31 17 19 20 24 25 26 27 28 29 30 23 22
ENGLISH General Description 1. Grinder adjustment knob 2. Coffee bean hopper 3. Pre-ground coffee compartment 4. Water tank + Lid 5. Coffee bean hopper lid 6. Control panel 7. Coffee dispensing spout 8. Full drip tray indicator 9. Cup holder grill 10. Drip tray 11. Coffee grounds drawer 12. Brew group 13. Service door 14. Grease for brew group (optional) 15. Power cord 16. Automatic Milk Frother 17. Suction tube for Automatic Milk Frother 18.
10 ENGLISH PREPARING FOR USE Machine Packaging The original packaging has been designed and constructed to protect the machine during transport. We recommend keeping the packaging material for possible future transport. Machine Installation 1 Remove the machine from the packaging. 2 For best use, it is recommended to: • • • Choose a safe, level surface where there will be no danger of overturning the machine or being injured.
ENGLISH 11 5 Rinse the water tank with fresh water. 6 Fill the water tank with fresh water up to the MAX level and reinsert it into the machine. Make sure it is fully inserted. Caution: Never fill the water tank with warm, hot, sparkling water or any other liquid, as this may cause damage to the water tank and the machine. 7 Lift the coffee bean hopper lid. 8 Slowly pour the coffee beans into the coffee bean hopper.
ENGLISH 12 Switch the power button to “I”. The " " button flashes. 13 To turn on the machine, simply press the " " button. Note: By keeping the button pressed for more than 8 seconds, the machine enters the demo mode. To exit the demo, disconnect the power cord and turn the machine back on. Yellow 12 14 The control panel indicates that the circuit must be primed.
ENGLISH 13 USING THE MACHINE FOR THE FIRST TIME When using the machine for the first time, the following activities need to happen: 1) You need to prime the circuit; 2) The machine will perform an automatic rinse/ self-cleaning cycle; 3) you need to perform a manual rinse cycle. Circuit Priming During this process, fresh water flows through the internal circuit of the machine and the machine warms up. This takes a few minutes. Yellow 1 Place a container under the steam wand.
ENGLISH Automatic Rinse/Self-Cleaning Cycle When warm-up has been completed, the machine automatically performs a rinse/self-cleaning cycle of the internal circuits with fresh water. This takes less than a minute. 5 Place a container under the coffee dispensing spout to catch the small Yellow amount of water which will be dispensed. 6 The machine shows this display. Wait for the cycle to finish automatically. Note: You can stop dispensing by pressing the “ ” button.
ENGLISH 15 Manual Rinse Cycle During this process the coffee brewing cycle is activated and fresh water flows through the water circuit. This takes a few minutes. Green Green 1 Place a container under the coffee dispensing spout. 2 Check that the machine shows this display. 3 Select the pre-ground coffee brewing function by pressing the “ ” button. The machine shows this display. Note: Do not add any pre-ground coffee into the compartment. 4 Press the “ ” button.
ENGLISH 7 Press the “ ” button to start dispensing hot water. Red 8 Dispense water until the no water icon appears. Note: The manual rinse cycle can be stopped by pressing the “ ” button. 9 At the end of this operation, fill the water tank again up to the MAX Green 16 level. Now the machine is ready to brew coffee. The display on the left will be shown. Note: The automatic rinse/self-cleaning cycle starts when the machine has been in stand-by mode, or turned off, for more than 15 minutes.
ENGLISH 17 Measuring and Programming Water Hardness Water hardness measuring is very important in order to define the descaling frequency and to install the “INTENZA+” water filter (for more details on the water filter, see next chapter). To measure the water hardness follow the steps below: 1 Immerse the water hardness test strip (supplied with the machine) in water for 1 second. Note: The test strip can only be used for one single measurement. 2 Wait for one minute.
Yellow ENGLISH 4 Press the “ ” button and scroll through the options by pressing the “ button until this icon is displayed. Note: The machine is supplied with a standard water hardness setting, suitable for most types of water. Yellow 5 Press the ““ ” button to increase the value and the “ decrease the value. 6 Press the “ 7 Press the ““ Green 18 ” button to ” button to confirm the setting. ” button to exit the programming MENU. The machine shows this display and is ready to brew.
ENGLISH 19 “INTENZA+” Water Filter Installation We recommend you to install the “INTENZA+” water filter as this prevents limescale build-up in your machine and preserves a more intense aroma of your coffee. The “INTENZA+” water filter can be purchased separately. For further details, please refer to the maintenance products page in this user manual. Water is a crucial part of every coffee, so it is very important to always have it professionally filtered.
ENGLISH 4 Put the “INTENZA+” water filter into the empty water tank. Press it down until it cannot move any further. 5 Fill the water tank with fresh water and put it into the machine. 6 Dispense all the water in the water tank by using the hot water function (see the “Dispensing Hot Water” chapter). Yellow Yellow 7 Fill the water tank again. 8 Press the “ ” button and scroll the options by pressing the “ until this display is shown.
ENGLISH 21 Replacing the “INTENZA+” Water Filter Yellow Yellow Yellow When the “INTENZA+” water filter needs to be replaced with a new one, this icon is displayed. 1 Replace the “INTENZA+” water filter as described in the previous chapter. 2 Press the “ ” button and scroll through the options by pressing the “ button until this icon is displayed. 3 Select the “RESET” option. Press the " Green 4 To exit, press the “ " button to confirm. ” button.
22 ENGLISH ADJUSTMENTS The machine allows for certain adjustments so that you can brew the best tasting coffee possible. Saeco Adapting System Coffee is a natural product and its characteristics may change according to its origin, blend and roast. The machine is equipped with a self-adjusting system that allows the use of all types of coffee beans available on the market, except for raw, caramelized and flavoured coffee beans.
ENGLISH 23 2 While the machine grinds coffee, press and turn the grinder adjustment knob placed inside the coffee bean hopper one notch at a time. Use the special coffee grinder adjustment key supplied. You will taste the difference after brewing 2-3 cups of coffee. 3 The reference marks inside the coffee bean hopper indicate the grind setting. There are 5 different grind settings to choose from, from position 1 ( ) for coarse grind - lighter taste to position 2 ( ) for fine grind stronger taste.
24 ENGLISH Adjusting the Coffee Dispensing Spout The height of the coffee dispensing spout can be adjusted to better fit the size of the cups that you wish to use. Move the coffee dispensing spout up or down with your fingers to adjust its height as shown in the figure. The recommended positions are: For the use of small cups; For the use of large cups. Two cups can also be placed under the coffee dispensing spout to brew two cups of espresso or coffee at the same time.
ENGLISH 25 Adjusting the Coffee Length The machine allows you to adjust the amount of brewed coffee according to your taste and the size of your cups. Each time the “ ” or “ ” button is pressed, the machine brews a pre-set amount of coffee. Each button may be individually programmed for a specific brew setting. 1 Place a cup under the coffee dispensing spout. ” button pressed until the “MEMO” icon appears on the display to program an espresso, or do the same with the “ ” button to program a coffee.
ENGLISH BREWING ESPRESSO AND COFFEE Before brewing coffee, make sure that there are no warnings shown on the control panel, and that the water tank and coffee bean hopper are filled. Brewing Espresso and Coffee Using Coffee Beans 1 Place 1 or 2 cups under the coffee dispensing spout. 2 To brew an espresso or a coffee, press the “ ” button to select the desired aroma. ” button for an espresso or the “ ” button for a coffee.
ENGLISH 27 Brewing Espresso and Coffee Using Pre-Ground Coffee This function allows you to use pre-ground coffee. Green With the pre-ground coffee function you can only brew one coffee at a time. 1 Press the “ ” button to select the pre-ground coffee function. 2 Lift the pre-ground coffee compartment lid and add one level measuring scoop of pre-ground coffee. Use only the measuring scoop supplied with the machine. Then close the pre-ground coffee compartment lid.
ENGLISH FROTHING MILK/BREWING CAPPUCCINO Frothing milk Warning: Danger of scalding! Dispensing may be preceded by small jets of hot water. When steam is used, the steam wand and the chrome cover may reach high temperatures. Never touch them with bare hands. The Automatic Milk Frother must be handled only as shown in the figure. 1 Fill 1/3 of a container with cold milk. Note: When preparing your cappuccino, use cold (~5°C / 41°F) milk with a protein content of at least 3% to ensure optimum results.
ENGLISH 29 3 Insert the suction tube into the Automatic Milk Frother. 4 Insert the Automatic Milk Frother into the steam wand seat. 5 Make sure that it is positioned correctly. If you cannot insert it, rotate the chrome cover. The Automatic Milk Frother is assembled correctly when the tooth fits into the slot. 6 Insert the suction tube into the milk container. Caution: For hygienic reasons, make sure that the outer surface of the suction tube is clean.
ENGLISH 7 Place a cup under the Automatic Milk Frother. 8 Press the “ ” button to start frothing milk. Green 9 This icon is displayed during the preheating time required by the machine. 10 When this icon is displayed, the machine dispenses frothed milk Green 30 directly in the cup. 11 Press the “ ” button to stop dispensing. Note: It will take a few seconds before the machine stops frothing milk completely. Note: Milk frothing stops after 3 minutes. ” again.
ENGLISH 31 Caution: After frothing milk, a small quantity of hot water must be dispensed into a container. See the "Daily cleaning of the Automatic Milk Frother" chapter for detailed cleaning instructions. Note: It is possible to brew an espresso or dispense hot water straight after frothing milk. Brewing a Cappuccino To prepare a cappuccino, place a cup of frothed milk under the coffee dispensing spout and brew an espresso.
ENGLISH 2 Place a container under the steam wand. 3 Press the “ ” button to start dispensing hot water. Green 4 This icon is displayed during the preheating time required by the machine. 5 Pour the desired amount of hot water. To stop dispensing hot water, Green 32 press the “ ” button.
ENGLISH 33 CLEANING AND MAINTENANCE Daily Cleaning of the Machine Caution: Timely cleaning and maintenance of your machine is very important as it prolongs the life of your machine. Your machine is continuously exposed to moisture, coffee and limescale! The activities you need to perform and their frequency are described in detail in this chapter. Not doing this will ultimately make your machine stop working properly. This repair is NOT covered by your warranty.
34 ENGLISH 1 4 Insert the coffee grounds drawer back into the drip tray and place the drip tray back into the machine. 2 3 Note: Empty and wash the drip tray also when the full drip tray indicator is raised. Daily Cleaning of the Water Tank 1 Remove the small white filter or the “INTENZA+” water filter (if installed) from the water tank and wash it with fresh water.
ENGLISH 35 Daily Cleaning of the Automatic Milk Frother For hygienic reasons and to ensure a perfect milk froth consistency, it is important that the Automatic Milk Frother be cleaned after each use. Warning: Danger of scalding! Dispensing may be preceded by small jets of hot water. After each milk frothing, you always need to: 1 Insert the suction tube into a container filled with fresh water. 2 Place an empty container under the Automatic Milk Frother. Green 3 Press the " " button to select steam.
36 ENGLISH Weekly Cleaning of the Machine 1 Clean the seat of the drip tray. Weekly Cleaning of the Brew Group The brew group should be cleaned every time the coffee bean hopper is filled or at least once a week. 1 Turn off the machine by pressing the “ ” button and unplug the power cord. 1 2 Remove the drip tray and coffee grounds drawer. 2 3 3 Open the service door.
ENGLISH 37 4 To remove the brew group, press the «PUSH» button and pull it by the handle. Pull it out horizontally without turning it. 5 Thoroughly clean the coffee outlet duct with the special cleaning tool provided with the machine or with a spoon handle. Make sure that the cleaning tool is inserted as shown in the figure. 6 Remove the coffee residues drawer and wash it thoroughly. 7 Thoroughly wash the brew group with fresh, lukewarm water and carefully clean the upper filter.
38 ENGLISH 10 Make sure that the brew group is in the off position; the two reference marks must match. If they do not match, proceed as described in step 11. 11 Gently pull down the lever until it is in contact with the brew group base and the two reference marks on the side of the brew group match. 12 Press the “PUSH” button firmly. 13 Make sure that the hook which locks the brew group is in the correct position.
ENGLISH 39 14 Insert the coffee residues drawer into its seat and ensure that it is correctly in place. Note: If the coffee residues drawer is not correctly positioned, the brew group may not fit into the machine. 15 Insert the brew group back into its seat until it locks into place without pressing the “PUSH” button. 16 Insert the coffee grounds drawer with the drip tray back into the machine and close the service door.
ENGLISH Monthly Cleaning of the Automatic Milk Frother Every month you need to perform a more thorough cleaning of the Automatic Milk Frother using the “Saeco Milk Circuit Cleaner”. The “Saeco Milk Circuit Cleaner” can be purchased separately. For further details, please refer to the maintenance products page in this user manual. Warning: Danger of scalding! Dispensing may be preceded by small jets of hot water. 1 Make sure that the Automatic Milk Frother is correctly installed.
ENGLISH 41 Green 7 This icon will be displayed during dispensing. When the solution has been completely dispensed, press the “ ” button to stop dispensing. Warning: Never drink the solution dispensed during this step. 8 Rinse the container thoroughly and fill it with ½ litre of fresh water to be used for the rinse cycle. 9 Insert the suction tube into the container. 10 Empty the container and place it back under the Automatic Milk Frother. Green 11 Press the " " button to dispense steam.
ENGLISH 13 This icon will be displayed during dispensing. When the water has Green 42 been completely dispensed, press the “ ” button to stop dispensing. 14 Empty the container. Caution: Let the steamwand cool down for a few minutes. 15 Remove the Automatic Milk Frother from the steam wand. 16 Remove the chrome cover with the rubber fitting from the steam wand. 17 Remove the rubber fitting from the chrome cover.
ENGLISH 43 18 Remove the suction tube. 19 Press the sides and disassemblel the Automatic Milk Frother as shown in the figure. 20 Remove the rubber lid as shown in the figure. 21 Wash all the components with lukewarm water. 22 Reassemble the lid making sure that you press it in the middle to have it correctly inserted.
44 ENGLISH 23 Reassemble the Automatic Milk Frother making sure it is correctly inserted. 24 Install the suction tube. 25 Insert the rubber fitting into the chrome cover. 26 Reinsert them back onto the steam wand. Caution: The tube could be hot if the machine has recently been used. Be careful! Do not insert the rubber fitting beyond the position shown. In this case, the Automatic Milk Frother would not work correctly as it would not be able to draw up milk.
ENGLISH 45 27 Insert the Automatic Milk Frother in the rubber fitting. 28 Make sure that it is positioned correctly. If you cannot insert it, rotate the chrome cover. The Automatic Milk Frother is assembled correctly when the tooth fits into the slot.
46 ENGLISH Monthly Lubrication of the Brew Group Lubricate the brew group after approximately 500 cups of coffee or once a month. The grease to lubricate the brew group can be purchased separately. For further details, please refer to the maintenance products page in this user manual. Caution: Before lubricating the brew group, clean it with fresh water and let it dry as described in the “Weekly Cleaning of the Brew Group” chapter. 1 Apply the grease evenly on both side guides.
ENGLISH 47 3 Insert the brew group into its seat until it locks into place (see the “Weekly Cleaning of the Brew Group” chapter). 4 Close the service door and insert the drip tray and coffee grounds drawer. Monthly Cleaning of the Brew Group with “Coffee Oil Remover” Besides weekly cleaning, we recommend performing a cleaning cycle with “Coffee Oil Remover” after approximately 500 cups of coffee or once a month. This operation completes the maintenance process for the brew group.
ENGLISH 3 Put a “Coffee Oil Remover” tablet in the pre-ground coffee compartment. 4 Press the “ Green 48 ” button one or more times to select the pre-ground coffee function without adding ground coffee to the compartment. 5 Press the “ ” button to start the coffee brewing cycle. 6 Wait until the machine has dispensed half a cup of water. 7 Switch the power button on the back of the machine to “0”. 8 Let the solution take effect for about 15 minutes. Make sure you discard the dispensed water.
ENGLISH 49 11 Wash the brew group thoroughly with fresh water. 12 After rinsing the brew group, insert it back into its seat until it locks into place (see the “Weekly Cleaning of the Brew Group” chapter). Insert the drip tray and the coffee grounds drawer. Close the service door. Green 13 Press the “ ” button to select the pre-ground coffee function without adding any pre-ground coffee into the compartment. 14 Press the “ ” button to start the coffee brewing cycle. 15 Repeat steps 13 to 14 twice.
ENGLISH DESCALING When the “CALC CLEAN” icon is displayed, you need to descale the machine. Yellow 50 The descaling cycle takes approx. 30 minutes. Caution: Not doing this will ultimately make your machine stop working properly. In this case, repair is NOT covered by warranty. Warning: Use the Saeco descaling solution only. Its formula has been designed to ensure better machine performance. The use of other products may damage the machine and leave residues in the water.
ENGLISH 51 Yellow 2 Remove the Automatic Milk Frother from the steam/hot water wand. 3 Press the Note: If you press the “ button. ” button by mistake, press the “ ” button to quit. 4 Remove the water tank and the “INTENZA+” water filter from the water tank (if it was installed), replacing it with the small white original one. Pour all the descaling solution into the water tank. 5 Fill the water tank with fresh water up to the CALC CLEAN level and put CALC CLEAN it back into the machine.
Yellow ENGLISH Yellow Yellow 7 Press the “ ” button to start the descaling process. 8 The machine will start dispensing the descaling solution at regular intervals for approximately 20 minutes. The bar on the control panel shows the cycle progress. Note: The descaling cycle may be paused by pressing the “ ” button. To resume the cycle, press the “ ” button again. This allows you to empty the container or to leave the machine unattended for a short time.
ENGLISH 53 1 11 Empty the drip tray and place it back. 2 3 12 Empty the container and place it back under both the steam/hot water Yellow wand and the coffee dispensing spout. Yellow 13 Press the “ ” button to start the rinse cycle. Note: The rinse cycle may be paused by pressing the “ ” button. To resume the cycle, press the “ ” button again. This allows you to empty the container or to leave the machine unattended for a short time.
ENGLISH 14 When the amount of water needed for the rinse cycle has been comRed 54 pletely dispensed, this icon is displayed. Press the “ ” button to quit the descaling cycle. Note: If you had not filled up the water tank to MAX level, the machine might require another rinse cycle. Refill the water tank and put it back into the machine. Repeat from step 13. 1 15 The machine warms up and performs the automatic rinse cycle. Remove and empty the container. Empty the drip tray and place it back.
ENGLISH 55 18 Make sure that it is positioned correctly. If you cannot insert it, rotate the chrome cover. The Automatic Milk Frother is assembled correctly when the tooth fits into the slot. 19 Clean the brew group. For more details, please see the “Weekly Cleaning of the Brew Group” chapter. 20 The machine is ready to brew coffee.
ENGLISH ACCIDENTAL INTERRUPTION OF THE DESCALING CYCLE Once you have started the descaling cycle, you must complete it till the very end without turning off the machine. If the descaling process is accidentally interrupted (power failure or accidental disconnection of the power cord), follow the steps below. 1 Make sure that the power button is on "I". Yellow 2 Press the “ ” button to turn on the machine.
ENGLISH 57 PROGRAMMING You can customise the machine's functions via the programming menu. Yellow Yellow Yellow Yellow Yellow Yellow The following settings can be adjusted Coffee Temperature This function allows you to adjust the coffee brewing temperature. Timer (stand-by) This function allows you to adjust the time taken for the machine to go into stand-by mode after the last brewing. Contrast This function allows you to adjust the contrast of the display to better view the messages.
Yellow ENGLISH Factory Settings This function allows you to reset all factory values. How to Program the Machine Green In this example, it is shown how to program the display contrast. Proceed in the same way to program the other functions. The programming menu can only be accessed when the machine is on and shows this display. Yellow 1 Press the “ ” button to access programming. 2 The main screen will be displayed.
ENGLISH 59 4 Press the “ ” and “ ” buttons to increase or decrease the value of Yellow the function. 5 Once the value has been changed, the “OK” message appears. Press the “ ” button to confirm the change. 6 Press the “ ” button to exit programming. Note: The machine automatically exits programming mode if no button is pressed for 3 minutes. The values that have been changed but not confirmed will not be saved.
60 ENGLISH MEANING OF THE DISPLAY ICONS This machine is equipped with a colour-coded system to make the user’s understanding of the display signals easier. The icons are colour-coded according to the traffic light principle. Ready Signals (Green Colour) The machine is ready to brew products. The machine is ready to brew pre-ground coffee. Hot water dispensing. Steam dispensing. The machine is brewing one cup of espresso. The machine is brewing one cup of coffee.
ENGLISH 61 Ready Signals (Green Colour) The machine is programming the amount of coffee to be brewed. Espresso brewing using pre-ground coffee in progress. Coffee brewing using pre-ground coffee in progress. The machine is warming up to dispense beverages.
62 ENGLISH Warning Signals (Yellow Colour) The machine is warming up. The machine is performing the rinse cycle. Wait until the machine has completed the cycle. The machine needs the "INTENZA+" water filter to be replaced. The brew group is being reset due to machine reset. Refill the coffee bean hopper with coffee beans. Prime the circuit. You need to descale the machine. Press the “ ” button to start the descaling process. Follow the steps described in the “Descaling” chapter of this manual.
ENGLISH 63 Warning Signals (Red Colour) Completely insert the drip tray with the coffee grounds drawer into the machine and close the service door. Fill the coffee bean hopper. The brew group must be inserted into the machine. Empty the coffee grounds drawer. Wait 5 seconds before reinserting it. Fill the water tank. The machine is out of order. The error code is displayed in the right bottom corner. For error codes 1 -3 - 4 - 5, please refer to the "Troubleshooting" chapter.
64 ENGLISH TROUBLESHOOTING This chapter summarizes the most common problems you could encounter with your machine. If you are unable to solve the problem with the information below, visit www.saeco.com/support for a list of frequently asked questions or contact the Philips Saeco hotline in your country. Contact details can be found in the warranty booklet packed separately or at www.saeco.com/support. Machine actions Causes Solutions Error Code 1 Coffee grinder blocked. Coffee outlet duct clogged.
ENGLISH 65 Machine actions Causes Solutions The machine does not turn on. The machine is not connected to the electric network, or the power button is in the “O” position. Water is sometimes drained automatically by the machine into the drip tray to manage the rinsing of the circuits and ensure optimum machine performance. The coffee grounds drawer has been emptied with the machine off. Connect the machine to the electric network and turn the power button to the “I” position.
66 ENGLISH Machine actions Causes Solutions The machine grinds coffee beans but no coffee comes out (see note)*. The brew group is dirty. Clean the brew group (see the "Weekly Cleaning of the Brew Group" chapter). Brew a few cups of coffee as described in the “Saeco Adapting System” chapter. Clean the coffee dispensing spout. Coffee is too weak (see note)*. Coffee is brewed slowly (see note)*. This might occur when the machine is automatically adjusting the dose.
ENGLISH 67 ENERGY SAVING Stand-by The Saeco fully automatic espresso coffee machine is designed for energy saving, as proven by the Class A energy label. After 15 minutes of inactivity, the machine turns off automatically (unless a different stand-by time has been programmed). If a product has been brewed, the machine performs a rinse cycle. In stand-by mode, the energy consumption is below 1Wh. To turn on the machine, press the “ ” button (if the power button on the back of the machine is set to “I”).
68 ENGLISH TECHNICAL SPECIFICATIONS The manufacturer reserves the right to make changes to the technical specifications of the product. Nominal Voltage - Power Rating Power Supply See data plate on the inside of the service door Housing material Thermoplastic material Size (w x h x d) 215 x 330 x 429 mm Weight 6.7 kg Power cord length 800 - 1200 mm Control panel Front panel Automatic Milk Frother Special for cappuccino Cup size Up to 152 mm Water tank 1.
ENGLISH 69 ORDERING MAINTENANCE PRODUCTS For cleaning and descaling, use Saeco maintenance products only. You can purchase the products at the Philips online shop at www.shop.philips.com/ service, from your local dealer or at authorised service centres. If you have any difficulties obtaining maintenance products for your machine, please contact the Philips Saeco hotline in your country. Contact details can be found in the warranty booklet packed separately or at www.saeco.com/support.
70 ENGLISH - Coffee Oil Remover CA6704 - Milk Circuit Cleaner: CA6705 - Maintenance Kit CA6706
del 30-12-14 02 EN Rev.00 02 The manufacturer reserves the right to make changes without prior notice. www.saeco.
