User manual

Never use scouring pads, abrasive cleaning agents or
aggressive liquids such as petrol or acetone to clean the
appliance.
Never rinse the appliance or the adapter under the
tap (Fig. 15).
Keep the appliance and the adapter dry (Fig. 16).
Cleaning the attachments
1 Remove the hair-lifting attachment with massage
element from the epilating head (Fig. 17).
Remove the shaving head comb attachment by
pulling it off the shaving head (Fig. 18).
2 Remove loose hairs from the attachments.
3 Rinse the attachments under the tap while turning
them.
4 Dry the attachments before you use or store them.
Cleaning the epilating head
1 Push the epilating head in the direction of the
arrows on the back of the appliance (1) and remove
it (2) (Fig. 9).
2 Remove loose hairs with the cleaning
brush (Fig. 19).
3 Rinse the epilating head under the tap for 5-10
seconds while turning it (Fig. 20).
4 Shake the epilating head rmly (Fig. 21).
Dry the epilating head thoroughly with a tea towel.
Note: Make sure the epilating head is completely dry before
you place it back onto the appliance.
Cleaning the shaving head
1 Push the shaving head in the direction of the
arrows on the back of the appliance (1) and remove
it (2). (Fig. 22)
2 Remove the shaving foil from the shaving
head. (Fig. 23)
3 Rinse the shaving foil and the inside of the shaving
head under the tap for 5-10 seconds while turning
them (Fig. 24).
4 Shake the shaving foil and shaving
head rmly (Fig. 25).
Dry the shaving foil and shaving head thoroughly with a
tea towel.
Note: Do not exert any pressure on the shaving foil to avoid
damage.
Note: Make sure the shaving foil and shaving head are
completely dry before you place it back onto the appliance.
5 Put the protection cap on the shaving head.
Tip: Rub a drop of sewing machine oil onto the shaving foil
twice a year.
Replacement
All parts of the appliance can be replaced. If you need to
replace one or more of the following parts, go to your
Philips dealer or an authorised Philips service centre:
appliance itself
epilating head
hair-lifting attachment with massage element
shaving head
shaving comb
cleaning brush
adapter
Environment
Do not throw away the appliance with the normal
household waste at the end of its life, but hand it in
at an ofcial collection point for recycling. By doing
this, you help to preserve the environment (Fig. 26).
Guarantee & service
If you need service or information or if you have a problem,
please visit the Philips website at www.philips.com or
contact the Philips Consumer Care Centre in your
country (you nd its phone number in the worldwide
guarantee leaet). If there is no Consumer Care Centre in
your country, go to your local Philips dealer.
-
-
-
-
-
-
-
-
-
-
-
Troubleshooting
This chapter summarises the most common problems
you could encounter with the appliance. If you are unable
to solve the problem with the information below, contact
the Consumer Care Centre in your country.
Problem Cause Solution
Poor epilating
results.
You move the
appliance in
the wrong
direction.
Move the appliance
against the direction
of hair growth, with
the on/off slide
pointing in the
direction in which
you move the
appliance.
You place
the epilating
head on the
skin at the
wrong angle.
Make sure that
you place the
appliance on the skin
at an angle of 90°
(see chapter ‘Using
the appliance’).
You used a
(depilatory)
cream prior to
epilation.
Make sure your skin
is clean, entirely dry
and free from grease.
Do not use any
cream before you
start epilating.
The hairs are
too short.
Sometimes hairs
are too short to be
caught. The optimal
length for easy
removal of the hairs
is 3-4mm. The hairs
that are not caught
during this session
will be long enough
to be removed when
you epilate the next
time. You can also try
to catch the hairs by
moving the appliance
across the skin a few
more times.
The
appliance
does not
work.
The socket
to which the
appliance is
connected is
not live.
Make sure the
socket is live. If you
have connected
the epilator to the
socket in a bathroom
cabinet, you may
need to switch
on the bathroom
light to activate the
socket.
I cannot
select speed
setting II.
The shaving
head is
attached. The
shaving head
can only be
used at speed
setting I.
Select speed setting
I when you use the
shaving head.
I cannot
remove the
shaving head/
epilating head
from the
appliance.
You try to pull
it straight off.
Push the epilating
head/shaving head
in the direction of
the arrows on the
back of the appliance
before you pull it off
the appliance (see
chapter ‘Cleaning and
maintenance’).
4203.000.4304.1
3/9