English 4 HQ6095, HQ6090 简体中文 14
English Important Read this user manual carefully before you use the appliance and save it for future reference. - This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. - Children should be supervised to ensure that they do not play with the appliance.
English Electromagnetic fields (EMF) This Philips appliance complies with all standards regarding electromagnetic fields (EMF). If handled properly and according to the instructions in this user manual, the appliance is safe to use based on scientific evidence available today. Charging Make sure the appliance is switched off before you start to charge it. When you charge the shaver for the first time or after a long period of disuse, let it charge for 4 hours. Charging normally takes approx. 1 hour.
English Charging the appliance Charge the appliance when the red power symbol burns or flashes or when the motor stops or starts to run slower. 1 Put the appliance plug in the shaver. 2 Put the powerplug in the wall socket. 3 Remove the powerplug from the wall socket and pull the appliance plug out of the shaver when the battery has been fully charged. Cordless shaving time A fully charged shaver has a cordless shaving time of up to 40 minutes.
English 4 Put the protection cap on the shaver every time you have used it, to prevent damage. Trimming For grooming sideburns and moustache. 1 Open the trimmer by pushing the slide upwards. The trimmer can be activated while the motor is running. Cleaning and maintenance Regular cleaning guarantees better shaving performance. The easiest and most hygienic way to clean the appliance is to rinse the shaving unit and the hair chamber with hot water every time you have used the appliance.
English 2 Press the release button (1) and open the shaving unit (2). 3 Clean the shaving unit and the hair chamber by rinsing them under a hot tap for some time. Make sure the inside of the shaving unit and the hair chamber have been cleaned properly. 4 Rinse the outside of the appliance. 5 Close the shaving unit and shake off excess water. Never dry the shaving unit with a towel or tissue, as this may damage the shaving heads.
English 2 Remove the retaining frame. 3 Clean the cutters and guards with the brush supplied. Do not clean more than one cutter and guard at a time, since they are all matching sets. If you accidentally mix up the cutters and guards, it may take several weeks before optimal shaving performance is restored. 4 Put the shaving heads back into the shaving unit and then put the retaining frame back into the shaving unit. Make sure that the projections of the shaving heads fit into the recesses.
10 English 2 Clean the trimmer with the brush supplied. 3 Lubricate the trimmer teeth with a drop of sewing machine oil every six months. Storage , Put the protection cap on the shaver to prevent damage. , Store the appliance in the pouch. Replacement Replace the shaving heads every two years for optimal shaving results. Replace damaged or worn shaving heads with HQ8 Precise Cutting System Shaving Heads only.
English 11 3 Remove the retaining frame. 4 Remove the shaving heads and place new ones in the shaving unit. Put the shaving heads back into the shaving unit and then put the retaining frame back into the shaving unit. Make sure that the projections of the shaving heads fit into the recesses. 5 Put the shaving unit back onto the shaver by inserting the hinge into the slot in the rim of the hair chamber and pushing it home until it locks into place (‘click’). 6 Close the shaving unit.
12 English Always remove the battery before you discard and hand in the shaver at an official collection point. Dispose of the battery at an official collection point for batteries. If you have trouble removing the battery, you can also take the shaver to a Philips service centre. The staff of this centre will remove the battery for you and will dispose of it in an environmentally safe way. Disposal of the battery Only remove the battery if it is completely empty.
English 13 Frequently asked questions Question Answer Why doesn’t the shaver shave as well as it used to? You may not have cleaned the appliance properly. Clean the shaving heads thoroughly (see chapter ‘Cleaning and maintenance’). Long hairs may be obstructing the shaving heads. Clean the cutters and guards properly with the brush supplied (see chapter ‘Cleaning and maintenance’). The shaving heads may be damaged or worn. Replace the shaving heads (see chapter ‘Replacement’).
14 简体中文 注意事项 使用产品之前,请仔细阅读本使用 说明书,并妥善保管以备日后参 考。 - 本产品不打算由肢体不健全、感 觉或精神上有障碍或缺乏相关 经验和知识的人(包括儿童)使 用,除非有负责他们安全的人对 他们使用本产品进行监督或指 导。 - 应照看好儿童,确保他们不玩耍 这些产品。 - 只能使用产品随附的电源插头。 - 电源插头可将 100-240 伏的电压 转换为 24 伏以下的安全低电压。 - 电源插头中含有一个变压器。切 勿将其剪断,而用另一个插头代 替,否则将导致严重后果。 - 不要使用已经损坏的电源插头。 - 电源软线不能更换,如果软线损 坏,此器具(电源适配器)应废 弃。如果电源插头已损坏,则必 须用原装型号替换,以免发生危 险。 - 必须在 5 摄氏度至 35 摄氏度之间 的温度下充电和存放剃须刀。
简体中文 15 - 不要将剃须刀放在软袋里充电。 - 确保电源插头干燥。 - 在自来水龙头下清洗剃须刀之 前,务必拔掉其电源插头。 - 此产品符合国际认可的 IEC 安全 标准,可放心在自来水龙头下清 洗。 使用热水时一定要小心。切记先检 查水温是否太高,以防烫手。 电磁场 (EMF) 这款飞利浦产品符合关于电磁场 (EMF) 的所有 相关标准。据目前的科学证明,如果正确使用 并按照本用户手册中的说明进行操作,本产品 是安全的。 充电 开始充电之前确保产品电源已关闭。 如果是首次充电,或长期未使用后的首次充 电,则应连续充电 4 小时。 充电通常需要约 1 小时。 您也可以不充电而将剃须刀插上电源后使用。 不要将本产品与电源接通超过 24 小时。 充电指示 充电 , 为没有电量的剃须刀充电时,绿色电源指示 灯开始亮起。
16 简体中文 电池已完全充满 , 电池完全充满电时,绿色电源指示灯开始闪 烁。 电池电量不足 , 当电池电量不足时,红色电池指示灯开始亮 起。当关闭剃须刀时,红色电池指示灯开始 闪烁。 为产品充电 当红色电源指示灯亮起或闪烁,或者当马达停 止或运行开始变慢时,请为产品充电。 1 将产品插头插入剃须刀。 2 将电源插头插入壁装插座。 3 电池充满后,从壁装式插座中拔下电源插 头,并从剃须刀上拔下产品插头。 不接电源的剃须时间 完全充电的剃须刀在不连接电源的情况下最长 可使用达 40 分钟。 使用本产品 剃毛 1 按一下开/关按钮打开剃须刀。 光环亮起。 2 将剃须刀头在皮肤上快速移动,作直线和迂 回动作。 在干爽的面部剃须效果最佳。 您的皮肤可能需要 2 到 3 周才能适应飞利浦剃 须系统。
简体中文 17 3 按一下开/关按钮关闭剃须刀电源。 4 每次使用后,盖上剃须刀保护盖,以防受 损。 修剪 用于修剪鬓角和小胡子。 1 向上推动滑块来打开修发器。 当马达运转时,修发器便可以启动。 清洁和维护 为保证更好的剃须效果,剃须刀必须定期清 洗。 最简单和最卫生的清洁方法是每次使用完本产 品之后,用热水冲洗剃须刀头部件和胡茬储藏 室。 使用热水时一定要小心。切记先检 查水温是否太高,以防烫手。 每天:剃须刀头部件和胡茬储藏室 1 关闭剃须刀电源,从壁装式电源插座中拔下 电源插头,并从剃须刀上拔下产品插头。 2 按下释放钮 (1) ,打开剃须刀头部件 (2)。
18 简体中文 3 在热水龙头下,冲洗剃须刀头部件和胡茬储 藏室一段时间。 确保剃须刀头部件和胡茬储藏室的内部已彻底 清洁。 4 冲洗产品表面。 5 关闭剃须刀头部件并甩掉多余的水份。 不要用毛巾或纸巾擦拭剃须刀头部 件,因为这样可能会损坏剃须刀 头。 6 再次打开剃须刀头部件,使它保持打开状 态,让产品完全晾干。 除了冲洗方式外,您还可以使用随附的刷子清 洁胡茬储藏室。 每 6 个月:剃须刀头 1 打开剃须刀头部件并将它从剃须刀上拔下。 您还可以让剃须刀头部件继续留在剃须刀上。 2 取下固定架。 3 用随附的刷子清洁刀片和网罩。 不要同时清洁多组刀片和网罩,因为它们都是 相互匹配的。如果不小心将刀片和网罩弄混,
简体中文 19 则需要数周时间才能恢复产品的最佳剃须性 能。 4 将剃须刀头放回剃须刀头部件,然后将固定 架放回剃须刀头部件。 确保剃须刀头凸起部位正好插入凹陷部位。 5 将剃须刀头部件装回剃须刀。方法是将铰链 插入胡茬储藏室边的槽中,将其推到位,直 到锁定到位(可听到“咔嗒”声)。 6 关闭剃须刀头部件。 修发器 每次使用后都要清洁修发器。 1 关闭剃须刀电源,从壁装式电源插座中拔下 电源插头,并从剃须刀上拔下产品插头。 2 用随附的刷子清洁修发器。 3 每六个月用一滴缝纫机油润滑修发器齿。
20 简体中文 存放 , 盖上剃须刀保护盖,以防受损。 , 将产品存放在软袋中。 更换 每两年更换一次刀头以获得最佳的剃须效果。 损坏或磨损的剃须刀头只能用 HQ8 剃须刀头 更换。 1 关闭剃须刀电源,从壁装式电源插座中拔下 电源插头,并从剃须刀上拔下产品插头。 2 打开剃须刀头部件并将它从剃须刀上拔下。 您还可以让剃须刀头部件继续留在剃须刀上。 3 取下固定架。 4 取下剃须刀头,在剃须刀头部件上装上新刀 头。将剃须刀头放回剃须刀头部件,然后将 固定架放回剃须刀头部件。 确保剃须刀头凸起部位正好插入凹陷部位。 5 将剃须刀头部件装回剃须刀。方法是将铰链 插入胡茬储藏室边的槽中,将其推到位,直 到锁定到位(可听到“咔嗒”声)。 6 关闭剃须刀头部件。
简体中文 21 附件 可选配以下附件: - HQ8500/HQ8000 电源插头 - HQ8 剃须刀头 环保 - 弃置产品时,请不要将其与一般生活垃圾堆 放在一起;应将其交给官方指定的回收中 心。这样做有利于环保。 - 内置充电电池含有可能会污染环境的物质。 丢弃剃须刀时,一定要将电池取出,并将剃 须刀送到官方指定的回收站。到官方指定的 电池回收站处理电池。如果您在取出电池时 遇到问题,您也可以将剃须刀送至飞利浦维 修中心。维修中心的员工会帮您取出电池, 并以环保的方式处理它。 处理电池 仅在电池电量完全耗尽后方可取出 电池。 1 从壁装式插座中拔下电源插头,并从剃须刀 上拔下产品插头。 2 让剃须刀运转直到停止,拧下螺钉并打开剃 须刀。 3 取出电池。 取出电池后,不要再将剃须刀与电 源连接在一起。
22 简体中文 保修与服务 如果您需要详细信息或有任何问题,请浏览飞 利浦网站,地址为 www.philips.
简体中文 23 HQ6095, HQ6090 200 /0 /0
24
25
26 4222.002.5093.