Always there to help you Register your product and get support at www.philips.
Contents 1 Important 2 2 2 3 3 3 2 Your SoundBar 4 4 4 4 5 3 Connect 6 6 Help and support Safety Care for your product Care of the environment Trademarks Assemble your Soundbar Main unit Remote control Connectors Placement Connect audio from TV and other devices 6 4 Use your SoundBar 8 8 8 8 8 5 Wall mount 9 Adjust the volume Choose your sound MP3 player Apply factory settings 6 Product specifications 10 7 Troubleshooting 11
1 Important Read and understand all instructions before you use your product. If damage is caused by failure to follow instructions, the warranty does not apply. Help and support Philips provides extensive online support. Visit our website at www.philips.com/support to: • download the user manual and the quick start guide • watch video tutorials (available only for selected models) • find answers to frequently answered questions (FAQs) • email us a question • chat with our support representative.
Risk of contamination! • Do not mix batteries (old and new or carbon and alkaine, etc.). • Danger of explosion if batteries are incorrectly replaced. Replace only with the same or equivalent type. • Remove batteries if they are exhausted or if the remote control is not to be used for a long time. • Batteries contain chemical substances, they should be disposed of properly. Risk of swallowing batteries! • The product/remote control may contain a coin/button type battery, which can be swallowed.
2 Your SoundBar Congratulations on your purchase, and welcome to Philips! To fully benefit from the support that Philips offers, register your SoundBar at www.philips.com/welcome. Assemble your Soundbar Assemble your SoundBar as described in the quick start guide (Step 1). • • • COAX/OPT: Lights up when you switch to coaxial input or optical input source. AUX: Lights up when you switch to analog input source. AUDIO-IN: Lights up when you switch to audio input source.
a (Standby-On) Switch the SoundBar on or to standby. b COAX Switch your audio source to the coaxial connection. Audio input from an MP3 player (3.5mm jack). Rear connectors c OPTICAL Switch your audio source to the optical connection. d TREBLE +/Increase or decrease treble. e SURR Toggle between stereo and virtual surround sound. f d a b e c Mute or restore volume. g BASS +/Increase or decrease bass. h VOLUME +/Increase or decrease volume.
3 Connect This section helps you connect your SoundBar to a TV and other devices. For information about the basic connections of your SoundBar and accessories, see the quick start guide. Note •• For identification and supply ratings, refer to the type plate at the back or bottom of the product. •• Before you make or change any connections, make sure Connect audio from TV and other devices Play audio from TV or other devices through your Soundbar speakers.
• The digital coaxial connector might be labeled DIGITAL AUDIO OUT. Option 3: Connect audio through analog audio cables Basic quality audio 1 Using an analog cable, connect the AUX connectors on your SoundBar to the AUDIO OUT connectors on the TV or other device.
4 Use your SoundBar Equalizer Change the high frequency (treble) and low frequency (bass) settings of the SoundBar. 1 This section helps you use the SoundBar to play audio from connected devices. Press TREBLE +/- or BASS +/- to change the frequency. »» All Source indicators on the main unit blink twice when treble or bass is set to the maximum or minimum value. Before you start • Make the necessary connections described in the quick start guide or download the user manual from www.philips.com/ support.
5 Wall mount Note •• Koninklijke Philips Electronics N.V. bears no responsibility for improper wall mounting that results in accident, injury or damage. If you have any query, contact Philips Consumer Care in your country. •• Before wall mounting, make sure the wall can support the weight of your SoundBar. Screw length/diameter Depending on the type of wall mounting your SoundBar, make sure that you use screws of a suitable length and diameter. 3 - 3.
6 Product specifications Note •• Specifications and design are subject to change without notice. Amplifier • • • • Total output power: 60W RMS (+/- 0.5 dB, 10% THD) Frequency response: 20 Hz-20 kHz / ±3 dB Signal-to-noise ratio: > 65 dB (CCIR) / (A-weighted) Input sensitivity: • AUX: 2 V • AUDIO-IN: 1V Audio • S/PDIF Digital audio input: • Coaxial: IEC 60958-3 • Optical: TOSLINK Main unit •• •• •• • • •• •• Power supply: 220-240 V~, 50 Hz - 60 Hz Power consumption: 30 W Standby power consumption: ≤ 0.
7 Troubleshooting Warning •• Risk of electric shock. Never remove the casing of the product. To keep the warranty valid, never try to repair the product yourself. If you have problems using this product, check the following points before you request service. If you still have a problem, get support at www.philips.com/support. Main unit The buttons on the SoundBar do not work. • Disconnect the SoundBar from the power supply for a few minutes, then reconnect. Sound No sound from SoundBar speakers.
Philips Electronics Australia Limited and Philips New Zealand Limited Warranty against Defects In this warranty: We or us means Philips Electronics Australia Limited ACN 008 445 743 or Philips New Zealand Limited (Company Number 1723), and our contact details are set out at the end of this warranty; You means the purchaser or the original end-user of the Goods; Supplier means the authorised distributor or retailer of the Goods that sold you the Goods in Australia or New Zealand; and Goods means the product
Specifications are subject to change without notice © 2013 Koninklijke Philips Electronics N.V. All rights reserved. HTL2150_79_UM_V1.