User manual Soundbar Speaker HTL3310 HTL3310 USER MANUAL Register your product and get support at www.philips.
Contents 1 Important Safety Care for your product Care of the environment Caution FCC and IC statement for Users (USA and Canada only) 2 Your Soundbar Main unit Wireless subwoofer Remote control Connectors Prepare the Remote Control Placement 3 3 4 4 5 Wall mount 13 6 Product specifications 14 5 7 Troubleshooting 15 6 6 6 6 7 8 8 3 Connect 9 9 9 9 10 10 4 Use your Soundbar 11 11 11 11 11 11 12 Connect to HDMI (ARC) Socket Connect to Optical Socket Connect to AUX Socket Connect to Power Pair
Read and understand all instructions before you use your product. If damage is caused by failure to follow instructions, the warranty does not apply. Safety Risk of electric shock or fire! • Before you make or change any connections, make sure that all devices are disconnected from the power outlet. • Never expose the product and accessories to rain or water. Never place liquid containers, such as vases, near the product.
• • • • battery can cause serious injury or death. Severe internal burns can occur within two hours of ingestion. If you suspect that a battery has been swallowed or placed inside any part of the body, seek immediate medical attention. When you change the batteries, always keep all new and used batteries out of reach of children. Ensure that the battery compartment is completely secure after you replace the battery. If the battery compartment cannot be completely secured, discontinue use of the product.
EN This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: 1. 2. FCC INFORMATION Warning: • This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
2 Your Soundbar Wireless subwoofer This section includes an overview of the Wireless subwoofer. Main unit This section includes an overview of the main unit. a b c a AC~ Socket Connect to the power supply. a b c d e f a Remote Control Sensor b Soundbar’s LED indicator • Green : AUX mode. • Green flash : USB mode. • Blue : Bluetooth mode. • Orange : OPTICAL mode. • White : HDMI ARC mode. c (SOURCE) Select an input source for the Soundbar. d +/- (Volume) Increase or decrease volume.
(Play/Pause) Start, pause or resume play in USB/BT mode. Connectors This section includes an overview of the connectors available on your Soundbar. e +/- (Volume) Increase or decrease volume. f Source buttons AUX: Switch your audio source to the MP3 connection (3.5mm jack). BT/PAIR: Switch to Bluetooth mode. Press and hold to activate the pairing function in Bluetooth mode or disconnect the existing paired Bluetooth device. OPTICAL: Switch your audio source to the optical connection.
Prepare the Remote Control • The provided Remote Control allows the unit to be operated from a distance. • Even if the Remote Control is operated within the effective range 19.7 feet (6m), remote control operation may be impossible if there are any obstacles between the unit and the remote control. • If the Remote Control is operated near other products which generate infrared rays, or if other remote control devices using infra-red rays are used near the unit, it may operate incorrectly.
Note English 3 Connect •• Your TV must support the HDMI-CEC and ARC function. HDMI-CEC and ARC must be set to On. This section helps you connect your Soundbar to a TV and other devices, and then set it up. For information about the basic connections of your Soundbar and accessories, see the quick start guide. Note •• For identification and supply ratings, see the type plate •• The setting method of HDMI-CEC and ARC may differ depending on the TV.
• Do not press Pair on the rear of the subwoofer, except for manual pairing. AUX L R AUDIO OUT • Use a RCA to 3.5mm audio cable (not included) to connect the TV’s audio output sockets to the AUX socket on the unit. Connect to Power • Before connecting the AC power cord, ensure you have completed all other connections. • Risk of product damage! Ensure that the power supply voltage corresponds to the voltage printed on the back or the underside of the unit.
Select Modes 1 This section helps you use the Soundbar to play audio from connected devices. Before you start • Make the necessary connections described in the quick start guide and the user manual. • Switch the Soundbar to the correct source for other devices. Turn ON and OFF • • • • When you first connect the unit to the main socket, the unit will be in STANDBY mode. The STANDBY indicator will light up red. Press the button on the remote control to switch the main unit ON or OFF.
Bluetooth Operation Through Bluetooth, connect the Soundbar with your Bluetooth device (such as an iPad, iPhone, iPod touch, Android phone, or laptop), and then you can listen to the audio files stored on the device through your Soundbar speakers. What you need • A Bluetooth device which supports Bluetooth profile A2DP, AVRCP and with Bluetooth version as 4.2 + EDR. • The maximum operational range between the Soundbar and a Bluetooth device is approximately 10 meters (30 feet).
Enjoy audio on a USB storage device, such as an MP3 player and USB flash memory, etc. 1 2 Insert the USB device. Press the button repeatedly on the unit or press the USB button on the remote control to select USB mode. 3 During playback: Button Action Start, pause or resume play. Skip to the previous or next track. / Tips 5 Wall mount English USB Operation Note •• Improper wall mounting may result in accident, injury or damage. If you have any query, contact Consumer Care in your country.
6 Product specifications Note •• Specifications and design are subject to change without notice. Bluetooth •• •• •• •• Bluetooth profiles: A2DP, AVRCP Bluetooth version: 4.2 + EDR Frequency band/ maximum power: 2402 MHz ~ 2480 MHz / -2 dBm 2.4G wireless •• 2.4G wireless frequency range: 2404.5 MHz ~ 2479.5 MHz •• 2.
Warning •• Risk of electric shock. Never remove the casing of the • • • • product. Reduce the distance between the remote control and the unit. Insert the battery with its polarities (+/-) aligned as indicated. Replace the battery. Aim the remote control directly at the sensor on the front of the unit. No power I can’t find the Bluetooth name of this unit on my Bluetooth device • • • • Ensure that the AC cord is properly connected. Ensure that there is power at the AC outlet.
产品中有害物质的名称及含量 Names and Contents of Hazardous Substances 有害物质 Hazardous Substance 部件名称 Name of the parts Housing 外壳 Subwoofer 超重低音箱 Loudspeakers 喇叭单元 PWBs 电路板组件 Accessories (Remote control & cables) 附件（遥控器， 电源线，连接线） Batteries in Remote Control (ZnC) (Pb) 铅 (Hg) 汞 (Cd) 镉 (Cr (VI)) 六价铬 多溴联苯 多溴二苯醚 O O O O O O X O O O O O O O O O O O X O O O O O X O O O O O X O O O O O (PBB) (PBDE) 遥控器电池 本表格依据 SJ/T 11364 的规定编制。 The table is formulated according to SJ/
FCC Supplier’s Declaration of Conformity Philips Soundbar Speaker/HTL3310/XX This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Envision Peripherals,Inc. 490 N McCarthy Blvd, Suite#120 Milpitas,CA95035 www.philips.
