LTC0500 Digital Black & white Camera Installation manual Installationsanleitung Manuel d’installation Manuale d’installazione Installatiehandleiding Manual de instalación Subject to changes without notice.
English Contents Contents FCC Statement ________________________________________________ 2 GB English ........................................................1 Important Safeguards ____________________________________________ 3 D Deutsch ....................................................19 1. Introduction ________________________________________________ 6 F Français ....................................................37 2.
English FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
English 9) Ventilation - Openings in the enclosure, if any, are provided for ventilation and to ensure reliable operation of the unit and to protect it from overheating.These openings must not be blocked or covered.This unit should not be placed in a built-in installation unless proper ventilation is provided or the manufacturer’ s instructions have been adhered to. 10) Power Sources - This unit should be operated only from the type of power source indicated on the marking label.
3 6 Introduction The LTC 0500 series digital Black & White camera offers an extremely high level of picture quality and resolution for use in surveillance and observation systems. It supports passive (DC) iris, video iris and manual iris lenses.The camera is suitable for C mount and CS mount lenses.The camera automatically detects and adapts to the type of lens fitted. 2 7 Preparation This manual describes how to install the hardware and how to use your video camera.
English 5 8 Mounting the lens The camera supports Manual Iris,Video Iris and DC Iris lenses. The use of Video or DC Iris lenses is recommended for outdoor use to prevent bleaching of the CCD. Lens connector specifications (rear view): VIDEO IRIS Lens mount, lens thread The lens mount should be C mount or CS mount (1”-32UN). No CS/C adapter is required when using C mount lenses. Auto Lens Detection At power-up the camera automatically detects the lens type in use and configures itself.
10 focus adjustment Back The back focus screw is an ‘endless’ screw that turns the back focus ring.Turning the screw in either direction will move the sensor chip back and forth from C mount position to CS mount position. C - CS Mount LENS English 6 11 Electrical Connections 7.1 AC MAINS POWER SUPPLY Mains Voltage models: LTC0500/50 CCIR LTC0500/60 EIA Power cable & inner conductors Camera models /50 are fitted with 2 wire power cable with Euro plug.
7.3 VIDEO CONNECTIONS BNC composite video Balanced 4 pin connector (selectable via PC software) Sync. Input Video output Video output 1 2 3 + 4 – 13 Mounting the camera Top mounting: Max lens weight: CVBS OUT 1/4” 20 UNC 0.5 kg Digital Camera N. C. N. C. N. C. N. C. Ground N. C. Rx Tx Mode switch H-V LOCK Balanced 7.
English Mode 3 Default mode Default Mode 2 Mode 1 Default mode 30 sec. Default 9.2.1 Mode setting The camera is delivered operating in Mode 1. In total three modes are available. Mode 1 = Backlight compensation Mode 2 = Traffic Mode 3 = Night (low light mode) Mode 0 is a non-programmable mode (Default mode) in which factory settings are stored. 9.2.2 Video level setting The nominal video level setting is 700 mV contrast. Adjustments are possible in +30/-30 steps.
English 9.2.7 H Phase This function is active when the camera operates with external synchronisation (H+V). Use the H-phase setting to adjust Horizontal timing differences when cameras are H-V synchronised. Input standard CVBS synchronisation signals. 9.2.8 ext V Phase This function is active when the camera operates with external synchronisation. (External V) Use the extV phase setting to adjust V phase differences when cameras are used in a system.
Inhalt MECHANICAL Dimensions: Weight: Camera mounting: Lens mounting: Lens weight: 65 x 70 x 149 mm (HxWxD*) * including connectors 0.6 kg Top and Bottom 1/4” 20 UNC C & CS 0.5 kg top mounting, 1.