Digital Home Cinema System 700 LX
Important Note Important notes for users in the U.K. Manufactured under license from Dolby Laboratories. “Dolby”, “Prologic” and the double-D symbol are trademarks of Dolby Laboratories. Mains plug This apparatus is fitted with an approved 13 Amp plug. To change a fuse in this type of plug proceed as follows: Confidential Unpublished Works. © 1992-1999 Dolby Laboratories, 1. Remove fuse cover and fuse. 2. Fix new fuse which should be a BS1362 5 Amp, A.S.T.A. or BSI approved type. 3.
Français English -------------------------------------------------------- 4 Español Français ------------------------------------------------------ 17 Deutsch Español ------------------------------------------------------ 30 Nederlands Deutsch ----------------------------------------------------- 43 Italianlo Nederlands ------------------------------------------------- 56 Svenska Italiano ------------------------------------------------------- 69 Dansk Svenska ----------------------------------
English Contents Introduction and General Information Features ............................................................................... 5 Supplied accessories ......................................................... 5 Environmental information.............................................. 5 Installation ........................................................................... 5 Maintenance........................................................................
Features Environmental information The LX700 Digital Home Cinema System creates the same dynamic sound qualities that you find in full-fledged cinemas and incorporates some of the best features in home theatre technology. All unnecessary packaging has been omitted. We have tried to make the packaging easy to separate into three materials: cardboard (box), polystyrene foam (buffer) and polyethylene (bags, protective foam sheet).
English Functional Overview Front and Rear panels 1 2 34 C 6 CHANNEL INPUT 5 6 7 1 SURROUND 7 PROGRAM – – 2 – 3 – 4 – 5 – 6 – to select multichannel surround(Dolby Digital, DTS, Dolby Pro Logic or Dolby Pro Logic II) or stereo sound effect. TUNING S T to select the tuner frequency. BASS to select bass adjustment mode. TREBLE to select treble adjustment mode. STANDBY ON y to switch between power on and standby mode. DISPLAY SCREEN shows the status of the system.
Remote DRAMA, ACTION,SCI-FI,CLASSIC, JAZZ, ROCK or DIGITAL. control @ SUBW +/– ¡ – 1 – ) – to adjust the subwoofer’s level. REAR +/to adjust the surround speakers’ level. CENTER +/to adjust the center speaker’s level. TV +/to adjust Philips’s television volume level. # SLEEP – 2 ( $ DIM * 4 % NIGHT (Dolby Digital mode only) DVD 3 5 6 7 8 9 0 ! to set the sleep (auto-off) timer function. 5 & ^ % $ – – to select different brightness for the display screen.
English Connections NEODYMIUM RIBBON TWEETER NEODYMIUM RIBBON TWEETER NEODYMIUM RIBBON TWEETER NEODYMIUM RIBBON TWEETER HI-FREOUENCY HI-FREOUENCY HI-FREOUENCY HI-FREOUENCY SUB + . AC MA INS ~ + + SUB IMPORTANT! – Before connecting the AC power cord to the wall outlet, ensure that all other connections have been made. – Never make or change any connections with the power switched on. – The type plate is located at the bottom of the system.
Connecting antennas Connecting from a DVD and additional components MW Indoor Loop Antenna Connect the supplied MW loop antenna to the MW jack. Position the loop antenna to receive the clearest sound. MW To listen to playback from your DVD or SACD player. Option 1 6 CHANNEL-DVD/SACD IN Use the supplied audio cables to connect the 6 CHANNELDVD/SACD IN jacks to the corresponding Multichannel AUDIO OUT on your DVD or SACD player.
English Connections Notes: – If the audio format of the digital input does not match the capabilities of your Receiver, it will produce a strong distorted sound or no sound at all – Always refer to the instruction manual of the connected equipment to make an optimal connection Preparations Placing the speakers To obtain the best surround effect, place the speaker as follows. Recording from the digital output It is possible to connect a digital recorder to the digital output of the receiver.
Selecting the surround mode IMPORTANT! – For proper surround sound, make sure you have followed the “Connections” and “Preparations” procedures fully. – The center and surround speakers only operate when the system is set to surround sound mode and the source material being played is recorded or broadcast in Dolby Digital, DTS, Dolby Pro Logic or Pro Logic II surround sound. – Stereo broadcasts or recordings will produce some surround channel effects when played in a surround mode.
English Basic Functions Volume Control Changing the volume level ● Adjust VOLUME button (or press VOL +/-) to increase or decrease the volume level. ➜ “VOL XX” is displayed. ➜ “VOL MAX” is displayed if volume is at maximum level. ● Press SUBW +/- to adjust the level of the subwoofer speaker volume. ➜ “SUBW XXDB” is displayed. ➜ The range is from -15dB to 10dB. ● Press REAR +/- to adjust the level of the surround speakers volume. ➜ “REAR XXDB” is displayed. ➜ The range is from -15dB to 10dB.
System Setup The system setup enables you to customize the Receiver. You can adjust the following features: Center Delay To enter System Setup, 1 Press PROGRAM on the Receiver for 5 seconds to enter the navigation menu. 2 Press S / T on the Receiver to toggle through the – If the listening position is closer to the center speaker than the front speakers, you can set the center delay time to improve the center sound effect. – Options : 5ms, 3ms, 2ms, 1ms, OFF.
English Others Functions Tuning to radio stations – In TUNER mode, press S or T briefly and repeatedly until the right frequency or optimum reception is obtained. – Press S or T more than 1 second if you want to activate automatic search tuning. Tuning automatically stops when a station of sufficient strength has been found. – Press TUNER again to select the desired band : FM or MW. Presetting radio stations You can preset up to 40 stations .
WARNING! Under no circumstances should you try to repair the system yourself, as this will invalidate the warranty. Do not open the system as there is a risk of electric shock. If a fault occurs, first check the points listed below before taking the system for repair. If you are unable to solve a problem by following these hints, consult your dealer or service center. Problem No power. No sound or distorted sound from speakers No sound is heard from center or rear speakers No sound from subwoofer.
English Specifications AMPLIFIER SECTION Output power Stereo mode (DIN) .................................................................................. 2 x 50 W Surround mode (1 kHz) ........................................... 50W RMS / channel Total Harmonic Distor tion ................... 10% at rated power (1 kHz) Frequency Response ......................................... 180Hz ~ 14 kHz / ±1 dB Signal-to-Noise Ratio ................................................................
