Register your product and get support at www.philips.
Contents 1 Important Mains fuse (UK only) Disposal of your old product and batteries Hearing safety Copyright notice Trademark notice 2 Your Blu-ray Component Hi-Fi System Feature highlights Playable media Product overview 3 Connect Preparations Connect speakers Connect video/audio cables Route audio from other devices Connect FM antenna Connect a USB device Connect a network Connect power 4 Get started Prepare the remote control Turn on Set clock Activate demonstration mode Find the TV input Use the
1 Important • Risk of electric shock or fire! • Never expose the product and accessories to rain or water. Never place liquid containers, such as vases, near the product. If liquids are spilt on or into the product, disconnect it from the power outlet immediately. Contact Philips Consumer Care to have the product checked before use. • Never place the product and accessories near naked flames or other heat sources, including direct sunlight.
Mains fuse (UK only) This information applies only to products with a UK mains plug. This product is fitted with an approved molded plug. If you replace the fuse, use one with: • the ratings shown on the plug, • a BS 1362 approval, and • the ASTA approval mark. Contact your dealer if you are not sure about what type of fuse to use. Caution: To conform with the EMC directive (2004/108/EC), do not detach the plug from the power cord.
Be sure to observe the following guidelines when using your headphones. • Listen at reasonable volumes for reasonable periods of time. • Be careful not to adjust the volume as your hearing adapts. • Do not turn up the volume so high that you can’t hear what’s around you. • You should use caution or temporarily discontinue use in potentially hazardous situations. Do not use headphones while operating a motorized vehicle, cycling, skateboarding, etc.
setup menu. Go to vod.divx.com with this code to complete the registration process and learn more about DivX VOD. DivX®, DivX Certified® and associated logos are registered trademarks of DivX, Inc. and are used under license. HDMI, and HDMI logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI licensing LLC in the United States and other countries. Java and all other Java trademarks and logos are trademarks or registered trademarks of Sun Microsystems, Inc.
2 Your Blu-ray Component HiFi System Congratulations on your purchase, and welcome to Philips! To fully benefit from the support that Philips offers (e.g. product software upgrade), register your product at www.philips.com/welcome. If you contact Philips, you will be asked for the model and serial number of this product. The model number and serial number are on the bottom of this product. Write the numbers here: Model No. _________________________ Serial No.
Product overview Main unit SOURCE a b d c n ml k a e j f i e • Turn on this product or switch to Eco Power standby mode. When EasyLink is enabled, press and hold for at least three seconds to turn all connected HDMI CEC compliant devices to standby. (Press and hold) switch between normal standby mode and Eco Power standby mode. • • b SOURCE • Select a source. c / • • Skip to the previous/next track or radio station. Skip to the previous/next title or chapter. • Start or pause play.
j Display panel a k Disc compartment • l • • Headphone socket. m MP3 LINK • Connect to an external audio device. • n • Connect to a USB flash drive. b Source and color buttons • Select a source. • BD-live: Select tasks or options. Remote control a z y Turn on this product or switch to Eco Power standby mode. When EasyLink is enabled, press and hold for at least three seconds to turn all connected HDMI CEC compliant devices to standby.
i w / • Skip to the previous or next title, chapter, or track. Skip to the previous/next title or chapter. • j / • • Search backward or forward. Tune to a radio station. k TREBLE • Enable treble adjustment. l BASS • Enable bass adjustment. • Access the home menu of this product. x DISC/POP-UP/MENU • BD: Access or exit the pop-up menu. • DVD: Access or exit the disc menu. y SLEEP/TIMER • Set the sleep timer. • Set the alarm timer. z TOP MENU • BD: Display the top menu.
3 Connect Make the following connections to use this product. Preparations 1 2 Place the apparatus near to the TV. Place the front left and right speakers at equal distance from the TV and at an angle of approximately 45 degrees from the listening position.
1 2 Unscrew the speaker connectors. 3 Screw the left red (+) connector to secure the cable. 4 Insert fully the silver end of a speaker cable into the left black (-) connector. 5 Screw the left black (-) connector to secure the cable. 6 Repeat steps 2-5 to insert the other speaker cable into the right connectors. Insert fully the red end of a speaker cable into the left red (+) connector. Connect video/audio cables Select the best video connection that the TV can support.
Option 2: Connect to the composite video jack Connect to an HDMI-compliant AV receiver/amplifier L L L R R R LINE OUT LINE IN AUX IN VIDEO IN VIDEO OUT L L R R LINE OUT HDMI IN AUX IN L R LINE OUT 1 Connect a composite video cable to: • the VIDEO jack on this product. • the VIDEO input jack on the TV. 2 Connect the audio cables to: • the LINE OUT/AUDIO -L/R jacks on this product. • the AUDIO input jacks on the TV.
1 Connect a coaxial cable (not supplied) to: • the COAXIAL jack on this product. • the COAXIAL/DIGITAL input jack on the device. L R LINE OUT Connect an analogue stereo system L L R R L LINE OUT AUX IN R L AUDIO IN R AUX IN L L R LINE OUT R AUX IN L Tip R LINE OUT 1 Connect the audio cables to: • the LINE OUT/AUDIO -L/R jacks on this product. • the AUDIO input jacks on the device. • Press MP3 LINK/AUX to select the audio output of your connection.
Tip • Press MP3 LINK/AUX to select the audio output of your connection. R LINE OUT R AUX IN Connect an iPod / iPhone dock FM With the connected iPod/iPhone dock, you can charge or listen to music from your iPod/ iPhone through this unit. R LINE OUT R AUX IN DOCK Connect a USB device 1 Connect a USB device to the (USB) jack on the front panel of this product. Note • Connect a dock (not supplied) to the DOCK socket on this unit.
Connect power 4 Get started Caution Caution • Risk of product damage! Ensure that the power • • Use of controls or adjustments or performance of procedures other than herein may result in hazardous radiation exposure or other unsafe operation. supply voltage corresponds to the voltage printed on the back of the unit. Before connecting the AC power cord, ensure you have completed all other connections. Always follow the instructions in this chapter in sequence.
Switch to normal standby mode • Press to switch the unit to normal standby mode. » The clock (if set) is displayed. To switch to Eco Power Standby mode: • Press and hold until the backlight on the display panel turns off. To deactivate the demonstration mode: 1 Press on the main unit again. Find the TV input 1 2 Press to turn on this player. Turn on the TV and switch to the video input (refer to the TV user manual on how to select the A/V input).
Set up a wired network Select a menu display language Note • Ensure that the network cables are properly connected. Note • If this product is connected to an HDMI CEC compliant TV, skip this setting. It switches automatically to the same OSD menu language as per your TV setting (if the language set on TV is supported by this product). 1 In the Home menu, select [Setup] and press OK. 2 3 Select [Preference], and press . 1 Connect a network cable (not supplied) to: • the LAN port on this product.
1 2 Connect a Philips Wi-Fi USB adapter (named WUB1110, sold separately) to the Wi-Fi port on the back of this product. Video Setup Network Installation View Network Settings Audio Setup View Wireless Settings Network Setup Turn on this product and the router. EasyLink Setup Preference R Advanced Wi-Fi R LINE OUT AUX IN 6 Internet Router Follow the on-screen instructions to complete the network installation.
One-touch play 1 Press (standby) to turn on this product. » The TV (if the TV supports onetouch play) automatically turns on and switches to the correct video-in channel. 4 Read the on-screen instructions and press OK to select [Continue]. » The product scans and displays the valid devices. 5 Press OK to select [Continue]. » If a disc is loaded in this product, disc play automatically starts.
5 Play Play a disc Caution • Do not place any objects other than discs into the disc compartment. 1 Press OPEN/CLOSE compartment. 2 3 Insert a disc with its label facing up. 1 Prepare a USB device that contains playable media files. 2 Connect the USB device to the (USB) socket on the front panel of this unit. » After the unit reads files in the USB device successfully, play starts automatically. 3 Press BACK. » A contents menu is displayed. 4 Select a file to play, and press OK.
Button Action Tip Pause play. Start or resume play. Stop play. Skip to a previous/next title or chapter. Search fast-backward or fastforward. Press repeatedly to change the search speed. / / Note • For BD discs with Java application, availability of the play resume function depends on specific discs. • If the PBC setting is off, the VCD/SVCD skips the menu and starts play from the first title. To display the menu before play, turn on the PBC setting (see “Adjust settings” > [Preference] > [VCD PBC]).
Repeat play for a specific section 1 During play, press MODE/OPTIONS. » The play options menu is displayed. 2 Select [Repeat A-B] in the menu, and press OK to set the starting point. 3 Continue the video play, and press OK to set the ending point. » Repeat play starts. • To cancel repeat play mode, press MODE/OPTIONS, and select [Repeat A-B] and press OK. Note • The marked section for repeat play is only possible within a track/title. 3 1 2 3 During play, press MODE/OPTIONS.
4 Play DivX® video DivX video is a digital media format that retains high quality despite a high rate of compression. to start slideshow play. Note • It may require longer time to display the disc content 1 Insert a disc or USB device that contains the DivX videos. • 2 Press , select [Play Disc] or [Browse USB], and press OK. » A contents menu is displayed. • 3 4 5 Select a video folder, and press OK. on the TV if there are a large number of songs/ photos compiled onto one disc.
Play MP3/WMA music Note • To create a musical slideshow, you must store the MP3/WMA and JPEG files on the same disc or USB device. 1 2 MP3/WMA is a type of compressed audio file (files with .mp3, .wma extensions). 1 Insert a disc or USB device that contains the MP3/WMA music. » Play starts automatically. 2 Press BACK. » A contents menu is displayed. 3 4 Select a music folder, and press OK. Play MP3/WMA music. Press menu.
6 Adjust settings • • • Note • If the setup option is grayed out, it means the setting cannot be changed at the current state. Video setup 1 2 3 Press • [4:3 Letterbox] – For 4:3 screen TV: wide-screen display with black bars on the top and bottom of the screen. [4:3 Panscan] – For 4:3 screen TV: fullheight display with the trimmed sides. [16:9 Widescreen] – For wide-screen TV: display picture at ratio 16:9.
[Picture Settings] Note Select a predefined set of picture color settings. • [Standard] – Original color setting. • [Vivid] – Vibrant color setting. • [Cool] - Soft color setting. • [Action] – Sharp color setting. It enhances the details in the dark area. Ideal for action movies. • [Animation] – Contrast color setting. Ideal for animated pictures. Audio setup 1 2 3 Press . Select [Setup], and press OK. Off Auto Audio Setup Network Setup Auto On EasyLink Setup Preference Advanced 4 5 BD-video.
Network setup EasyLink setup 1 2 3 1 2 3 Press . Select [Setup], and press OK. Select [Network Setup], and press . Video Setup Network Installation Press . Select [Setup], and press OK. Select [EasyLink Setup], and press . Video Setup View Network Settings Audio Setup Audio Setup View Wireless Settings Network Setup Network Setup 4 5 EasyLink Setup EasyLink Setup Preference Preference Advanced Advanced Select an option, then press OK. Select a setting, then press OK.
[System Audio Control] [Menu Language] When you play audio that is routed from the connected device, this unit switches to the corresponding audio source automatically. • [On] - Turns on System Audio Control. Then proceed to [Audio Input Mapping] to scan and map the connected device. • [Off] - Disables System Audio Control. Select an on-screen menu language. [Audio Input Mapping] Updates audio input mapping if there are new devices connected.
[Screen Saver] Video Setup Turn on or off the screen saver mode. It helps to protect the TV screen from being damaged due to over exposure to static image for being too long. • [On] - Set the screen saver active after 10 minutes of inactivity (for example, in the pause or stop mode) • [Off] - Disable screen saver mode. [Change Password] Set or change the password. 1) Press the Numeric buttons to enter the password or your last set password. If you forget the password, enter ‘0000’, then press .
[DivX® VOD Code] Obtain the DivX® registration code or the deregistration code. Tip • Use the DivX registration code of this product when you rent or purchase video from www.divx.com/ vod. The DivX videos rented or purchased through the DivX® VOD (Video On Demand) service can be played only on the device to which it is registered. 7 Tune to FM radio stations 1 Ensure that you have connected and fully extended the supplied FM antenna. 2 3 4 Press RADIO. [Version Info.
Program radio stations manually Note • You can program a maximum of 40 preset radio stations. 1 2 Tune to a radio station. 3 Press / to allocate a number from 1 to 40 to this radio station, then press PROGRAM to confirm. » The preset number and the frequency of the preset station are displayed. 4 Press PROGRAM to activate programming. Set RDS clock You can use time signal broadcast together with the RDS signal to set the clock of the unit automatically.
8 Adjust volume level and sound effect Adjust volume level 1 During play, press VOL +/- to increase/ decrease the volume level. Select a sound effect Note • You cannot use different sound effects at the same time. Adjust bass level 1 During play, press BASS to enter bass adjustment. 2 Press VOL +/- to adjust the bass level. Adjust treble level 1 During play, press TREBLE to enter treble adjustment. 2 Press VOL +/- to adjust the treble level.
9 Additional Information 7 Press SLEEP /TIMER to confirm. » The volume level indicator begins to blink. 8 Press VOL +/- to set the volume level, then press SLEEP /TIMER to confirm. » An alarm icon is displayed. Adjust brightness of display panel 1 Note In standby mode, press DIM repeatedly to select different levels of brightness for the display panel. • In standby mode, press SLEEP /TIMER repeatedly to activate/deactivate the alarm timer.
Update software via network 1 Set up the internet connection (see “Get started’ > “Set up a network”). 2 In the Home menu, select [Setup] > [Advanced] > [Software Update] > [Network]. » You are prompted to start the upgrading process if upgrade media is detected. 3 Follow the instructions on the TV screen to confirm update operation. » Once software update is complete, this product restarts automatically. Update software via USB 1 Go to www.philips.
S/PDIF digital audio output: • Coaxial: IEC 60958-3 USB • Compatibility: Hi-Speed USB (2.0) • Class support: UMS (USB Mass Storage Class) Main unit • Power supply rating • Europe: 220-240V~, 50/60Hz • Power consumption: 40W • Power consumption in standby mode: < 0.5 W • Dimensions (w x h x d): 256 x 94 x 296 (mm) • Net weight: 2.7 kg Speakers • Speaker impedance: 6ohm • Speaker driver: 5.25” woofer+3” tweeter • Sensitivity: >80dB/m/W ± 4dB/m/W • Dimensions (w x h x d): 176 x 260 x 240 (mm) • Net weight: 3.
10 Troubleshooting Warning • Risk of electric shock. Never remove the casing of the product. To keep the warranty valid, never try to repair the product yourself. If you have problems using this product, check the following points before you request service. If you still have a problem, register your product and get support at www.philips. com/welcome. Main unit No reaction to the remote control. • Connect this product to the power outlet.
• • • Ensure that this product supports the region code of the DVD or BD. For DVD±RW or DVD±R, ensure that the disc is finalized. Clean the disc. Data files (JPEG, MP3, WMA) cannot be played or read. • Ensure that the data file was recorded in the UDF, ISO9660 or JOLIET format. • Ensure that the disc does not contain more than 9,999 files for DVD, and 999 files for CD. • Ensure that the JPEG file extension is.jpg, .JPG, .jpeg or .JPEG. • Ensure that the MP3/WMA file extension is .mp3 or .MP3, and .wma or .
11 Glossary A Aspect ratio Aspect ratio refers to the width to height ratio of TV screens. The ratio of a standard TV is 4:3, while the ratio of a high-definition or wide TV is 16:9. The letter box allows you to enjoy a picture with a wider perspective on a standard 4:3 screen. AVCHD AVCHD is a format (standard) for high definition video cameras that can be used to record and play high-resolution HD images.
J R JPEG A very common digital still picture format. A still-picture data compression system proposed by the Joint Photographic Expert Group, which features small decrease in image quality in spite of its high compression ratio. Files are recognized by their file extension ‘.jpg’ or ‘.jpeg.’ Region code A system that allows discs to be played only in the region designated. This unit only plays discs that have compatible region codes. You can find the region code of your unit on the product label.
© 2011 Koninklijke Philips Electronics N.V. All rights reserved. MBD7020_12_UM_V1.
