MCB395 Micro Hi-Fi System Register your product and get support at www.philips.com/welcome User manual Benutzerhandbuch Manuale dell'utente Brukerhåndbok Brugervejledning pg 001-029_MCB395_05-04 1 2008.5.
Important notes for users in the U.K. Mains plug This apparatus is fitted with an approved 13 Amp plug. To change a fuse in this type of plug proceed as follows: 1 2 Remove fuse cover and fuse. 3 Refit the fuse cover. Fix new fuse which should be a BS1362 5 Amp, A.S.T.A. or BSI approved type. If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate plug fitted in its place. If the mains plug contains a fuse, this should have a value of 5 Amp.
1 2 ^ 3 % 4 $ # 5 6 7 5 @ 7 8 9 ! 0 3 pg 001-029_MCB395_05-04 3 3 2008.5.
Italia DICHIARAZIONE DI CONFORMITA’ Si dichiara che l’apparecchio MCD289 Philips risponde alle prescrizioni dell’art. 2 comma 1 del D.M. 28 Agosto 1995 n. 548. Fatto a Eindhoven Philips Consumer Electronics Philips, Glaslaan 2 5616 JB Eindhoven, The Netherlands Norge Typeskilt finnes på apparatens underside. Observer: Nettbryteren er sekundert innkoplet. Den innebygde netdelen er derfor ikke frakoplet nettet så lenge apparatet er tilsluttet nettkontakten.
English Index Deutsch English ------------------------------------------------ 6 Italiano Deutsch --------------------------------------------- 30 Bokmål --------------------------------------------- 78 Dansk --------------------------------------------- 102 5 pg 001-029_MCB395_05-04 5 2008.5.
Contents English DAB Reception General Information Supplied accessories ............................................ Environmental Information ................................ Safety Information ................................................ About MP3 disc .................................................... Hearing Safety ....................................................... 7 7 7 7 8 Preparations Rear connections .................................................
Congratulations on your purchase and welcome to Philips! ● The ventilation should not be impeded by covering the ventilation openings with items, such as newspapers, table-cloths, cur tains, etc. To fully benefit from the support that Philips offers, register your product at www.philips.com/ welcome. ● Do not expose the system, batteries or discs to excessive moisture, rain, sand or heat sources caused by heating equipment or direct sunlight.
General Information English Hearing Safety Listen at a moderate volume. ● Using headphones at a high volume can impair your hearing. This product can produce sounds in decibel ranges that may cause hearing loss for a normal person, even for exposure less than a minute. The higher decibel ranges are offered for those that may have already experienced some hearing loss. ● Sound can be deceiving. Over time your hearing "comfort level" adapts to higher volumes of sound.
English Preparations DAB/FM T-type antenna Speaker (right) Speaker (left) AC power cord Rear connections B FM/DAB antenna connection The type plate is located at the rear of the system. For users in the U.K.: please follow the instructions on page 2. A Power ● Before connecting the AC power cord to the wall outlet, ensure that all other connections have been made. Hang up one end of the T-shape DAB/FM antenna and keep the other end at horizontal angle to it to ensure sound DAB reception.
Preparations English 2 C Speakers Connection Front Speakers Connect the speaker wires to the SPEAKERS terminals, right speaker to "R" and left speaker to "L", coloured (marked) wire to "+" and black (unmarked) wire to "-". OR 1 2 1 2 ● Fully insert the stripped portion of the speaker wire into the terminal as shown. Insert the other plug of the USB cable to the USB output terminal of the USB device. for the memory card: Insert the memory card into a card reader (not supplied).
Replacing battery (lithium CR2025) into the remote control Before using the remote control 1 2 3 Pull out the plastic protective sheet. Select the source you wish to control by pressing one of the source select keys on the remote control (for example CD, TUNER). Then select the desired function (for example ÉÅ , à , á). 1 2 3 Press the slot on the battery compartment. Pull out the battery compartment. Replace a new battery and fully inser t the battery compartment back to the original position.
Controls English Controls on the set (illustrations on page 3) @9 for CD/MP3-CD/USB ................................. to stop playback or to clear a programme. 1 Display screen – to view the current status of the system. 2 Eco Power/STANDBY ON y – – press briefly to switch the set on or off (standby/ ECO POWER); In standby or Eco Power mode: press and hold to toggle between Standby and ECO POWER mode (power-saving mode). scans DAB radio stations automatically.
English Controls 7 REPEAT/ST. Remote control for CD/MP3/USB selects a repeat playback mode. for FM .................. sets stereo or mono sound mode. 1 8¡ 2 7 5 4 6 9 9 0 8 ¡ 3 ! ™ @ ) £ ( * & ^ % # $ /™ for CD/MP3-CD/USB ................................. skips to the beginning of a current/previous/subsequent track. for FM/DAB ................................. tunes to preset FM radio station or DAB frequency. 9 5 /6 for CD/MP3-CD/USB .................................
Controls English ( DISPLAY for CD/MP3/USB ................................. displays track information during playback. ) VOL +/– – adjusts the volume level. adjusts the hours and minutes for the clock/timer function. ¡ SLEEP – selects the sleeper time. ™9 – stops disc playback or erases a disc/USB program. £ MUTE – interrupts and resumes sound reproduction.
English Basic Functions ● Press and hold ECO POWER/STANDBY ON 2 for 3 seconds or more to go back to Eco Power Standby mode. Power-saving automatic standby As a power-saving feature, the system will automatically switch to Standby mode if you do not press any buttons within 15 minutes after a disc has stopped playing. Volume control IMPORTANT! Before you operate the system, complete the preparation procedures.
CD/MP3-CD Operations English To interrupt playback ● Press ÉÅ. ● To resume playback, press ÉÅ again. To stop playback ● Press Ç. Notes: – Disc play will also stop when you select another source or the disc has reached the end. – For MP3 disc, the disc reading time may exceed 10 seconds due to the large number of songs compiled into one disc. Text display IMPORTANT! The lens of the CD player should never be touched.
1 2 Finding a passage within a track Programming the disc tracks Press and hold down on TUNING S / T. ➜ The disc is played at high speed. Programming tracks is possible when playback is stopped. Up to 32 tracks can be stored in the memory in any order. When you recognize the passage you want, release TUNING S / T. ➜ Normal playback continues. Selecting a desired album/track (MP3 disc only) To select a desired album ● Press ALBUM/PRESET 4 / 3 repeatedly.
DAB Reception English Re-tuning By re-tuning, you can update your DAB multiplex (ensemble) list all over again. At the completion of scanning, the system will tune to the first service of the first multiplex (ensemble) in the updated multiplex (ensemble) list. During scanning, the system will initially display the following the following, where "CH" is the DAB channel and "N" is the number of the current multiplex (ensemble). CH N ● Press SCAN briefly.
● DAB information display Programming DAB stations You can view the DAB service information in the following 3 information modes. Depending on the DAB radio station you are tuning to, some information modes may be unavailable. You can save up to 20 DAB stations in the system memory. Press INFO./RDS repeatedly to view the following information. Channel & Frequency Displays the channel and central frequency of the current multiplex (ensemble).
Tuner English Tuning to radio stations Manual programming 1 Press SOURCE once or more to select FM (or FM on the remote control) . 1 2 Press and hold 4 / ¢ (or 5 /6 on the remote control) until SEARCH appears ➜ The radio automatically tunes to a station with sufficient reception. Display shows SEARCH during automatic tuning. 2 3 Press ALBUM/PRESET 43 (or ¡ / ™ on the remote control) to allocate a number from 1 to 20 to this station. Repeat step 2 if necessary until you find the desired station.
English Tuner RDS The feature RDS (Radio Data System) is a service that allows FM stations to send additional information along with the regular FM radio signal. When you are receiving an RDS station, and the station name are displayed. Switching through RDS information 1 2 Tune to the desired RDS radio station on the FM waveband (see Tuning to radio stations) Press INFO.
External Sources English Using a non-USB device 1 2 Connect the audio out terminals of the external equipment (TV, VCR, Laser Disc player, DVD player or CD Recorder) to the LINE-IN terminal of your system. Press SOURCE repeatedly (or AUX on the remote control) to select external equipment. Notes: – All the sound control features (DSC or DBB, for example) are available for selection. – Refer to the operating instructions for the connected equipment for details.
How to organize your MP3/WMA files on the USB mass storage device This Hi-Fi system will browse the MP3/WMA files in the folders/sub-folders/titles order. Example: 1 2 Root 3 Title 001 Title 002 Title 003 Album 01 Title 001 Title 002 Title 003 Album 02 Title 001 Title 002 Title 003 English External Sources Check the USB device has been properly connected. (See Installation: Connecting an additional appliance). Press SOURCE (USB on the remote) once or more to select USB.
Clock/Timer English Setting clock 1 Press and hold TIMER on the remote control. ➜ TIMER ON and the hours digits start flashing. 2 Adjust VOLUME -/+ (or press VOL +/- on the remote control) to set the hours. 3 Press TIMER to confirm. ➜ The minutes digits start flashing. 4 Adjust VOLUME -/+ (or press VOL +/- on the remote control) to set the minutes. 5 Press TIMER to confirm . ➜ TIMER OFF and the hours digits start flashing.
English Timer/Sleep Activating and deactivating TIMER ● Press TIMER on the remote repeatedly to activate or deactivate the timer. ➜ If activated, the last set source and start time are displayed. ➜ If deactivated, “TIMER OFF” appears.. Helpful hints: The timer will not work at the set time if – the timer is deactivated. The set will switch to Tuner source automatically if : – no CD is inserted when the selected source is CD; – no USB device is connected when the selected source is USB.
Specifications English AMPLIFIER Output power ....................................... 2 x 50 W RMS ...................................................... 100 W + 100 W MPO Signal-to-noise ratio .......................... ≥ 62 dBA (IEC) Frequency response ......... 40 – 15000 Hz, ± 3 dB Impedance loudspeakers ......................................... 4 Ω Impedance headphones .................... 32 Ω -1000 Ω CD/MP3-CD PLAYER Number of programmable tracks ......................... 20 Frequency range ........
Cleaning the Cabinet ● Use a soft cloth slightly moistened with a mild detergent solution. Do not use a solution containing alcohol, spirits, ammonia or abrasives. Cleaning Discs ● When a disc becomes dirty, clean it with a cleaning cloth. Wipe the disc from the centre out. ● Do not use solvents such as benzene, thinner, commercially available cleaners, or antistatic spray intended for analogue records. Cleaning the disc lens ● After prolonged use, dirt or dust may accumulate at the disc lens.
Troubleshooting English WARNING Under no circumstances should you try to repair the system yourself, as this will invalidate the warranty. Do not open the system as there is a risk of electric shock. If a fault occurs, first check the points listed below before taking the system for repair. If you are unable to remedy a problem by following these hints, consult your dealer or Philips for help. Problem Solution “NO DISC” is displayed. ✔ ✔ Some files on the USB device are not displayed.
The remote control does not function properly. ✔ Select the source (CD or TUNER, for example) ✔ ✔ ✔ ✔ before pressing the function button (ÉÅ,í, ë). Reduce the distance between the remote control and the system. Insert the battery with its polarities (+/– signs) aligned as indicated. Replace the battery. Point the remote control directly toward IR sensor on the front of the system. The timer is not working. ✔ Check the set is switched off ✔ Set the clock correctly. ✔ Press TIMER to switch on the timer.
Meet Philips at the Internet http://www.philips.com English Deutsch Italiano Bokmål Dansk Italiano Svenska MCB395 Dansk Suomi CLASS 1 LASER PRODUCT Português Polski Printed in China PageBack_MCB395 76 PDCC-JW-0817 2008.5.
