Register your product and get support at www.philips.
Important safety instructions Warning • The Electrical network is classified as hazardous. The only way to power down the charger is to unplug the power supply from the electrical outlet. Ensure that the electrical outlet is always easily accessible. • Refer to safety information before using the product. • This product complies with European R&TTE directive 1999/5/EC • Use only the power supply listed in the user instructions. • Use only the batteries listed in the user instructions.
1 Overview In call / Enter the option menu. OK Change the sound profile. Adjust the volume. Recall (network dependent). End calls. Turn the speaker on/off. Mute/unmute the microphone. Enter a pause (press and hold). Standby / Access the main menu. OK Access the redial list. Phonebook Call log Make and receive calls. Make intercom call (press and hold). Multi-handset version only. Lock/unlock the keypad (press and hold). Make and receive calls through the speaker.
Connect 2 2 1
3 Get started Configure your phone 1 The batteries are pre-installed in the handset. Pull the battery tape off from the battery door before charging. 2 When using your phone for the first time, you see a welcome message (country dependent). 3 Set the country and language if prompted. 4 Set the date and time. to • If the time is in 12-hour format, press / select [am] or [pm] (country dependent). Charge your phone Charge 8 hours Charge your handset by docking it in either direction.
4 Enjoy Phonebook Add record 1 Press > [Option] > [Add new]. 2 Follow on-screen instructions. Call from the phonebook 1 Press . 2 Select a record and press . Direct access memory You have 9 direct access memories (Keys 1 to 9). To dial the saved phone number automatically, press and hold on the keys in standby mode. Depending on your country, keys 1 and 2 are preset to the voice mail number and information service number of your service provider respectively (network dependent).
5 Learn more Silent mode Sets time during which the phone will not ring > [Silent mode] MySound Customizes the sound of voices to your liking > [MySound] Eco mode Reduces power consumption / transmission power; reduces radiation and range by approximately 60% > [Eco mode] Eco+ mode Eliminates radiation in standby mode (causes 2 seconds ring delay, 50% shorter standby time) > [ECO+ mode] Call barring Prevents unwanted outgoing calls to selected numbers > [Call barring]
Technical data Battery • Philips: 2 x AAA NiMH 1.2 V Rechargeable 550 mAh batteries Use only the supplied batteries. Adapter • MEIC: MN-A075-U056 Input: 100-240 V~ 50/60 Hz 200 mA; Output: (i)6.5 V 300 mA, (ii)7.5 V 200 mA Phonebook with 250 entries Call log with 50 entries Talk time: 18 hours Standby time: 250 hours Note • You can install a DSL (digital subscriber line) filter to prevent noise and caller ID problems caused by the DSL interference. • You can find the Declaration of Conformity on www.p4c.
Frequently asked questions No signal bar is displayed on the screen. • The handset is out of range. Move it closer to the base station. • If the handset displays [Register your Handset], register your handset. (See the section on “Register additional handsets”). If I fail to pair (register) the additional handsets to the base station, what do I do? Your base memory is full. Press . Then press / to select > [Unregister] to unregister the unused handsets and try again.
www.philips.com/support For information, refer to the extended user documentation online.
0168 When this crossed-out wheeled bin symbol is attached to a product it means that the product is covered by the European Directive 2002/96/ EC. Reproduction in whole or in part is prohibited without the written consent of the copyright owner. Trademarks are the property of Koninklijke Philips Electronics N.V. or their respective owners. All rights reserved. © 2013 Koninklijke Philips Electronics N.V. UMS_M888 05_EN_V1.
