manual

AE 2160
Portable Radio
8
4
5
6
7
3
2
1
1
Important notes for users in the U.K.
Mains plug
This apparatus is fitted with an approved 13 Amp plug. To change a
fuse in this type of plug proceed as follows:
1 Remove fuse cover and fuse.
2 Fix new fuse which should be a BS1362 5 Amp, A.S.T.A. or BSI
approved type.
3 Refit the fuse cover.
If the fitted plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place. If the mains plug
contains a fuse, this should have a value of 5 Amp. If a plug without a
fuse is used, the fuse at the distribution board should not be greater
than 5 Amp.
Note: The severed plug must be disposed of to avoid a possible shock
hazard should it be inserted into a 13 Amp socket else where.
How to connect a plug
The wires in the mains lead are coloured with the following code:
blue = neutral (N), brown = live (L). As these colours may not corre-
spond with the colour markings identifying the terminals in your plug,
proceed as follows:
• ConnectthebluewiretotheterminalmarkedNorcolouredblack.
• ConnectthebrownwiretotheterminalmarkedLorcolouredred.
• Donotconnecteitherwiretotheearthterminalintheplug,mar-
ked E (or
e
) or coloured green (or green and yellow).
Before replacing the plug cover, make certain that the cord grip is
clamped over the sheath of the lead - not simply over the two wires.
Copyright in the U.K.
Recordingandplaybackofmaterialmayrequireconsent.SeeCopyright
Act 1956 and The Per form er’s Protection Acts 1958 to 1972.
Note:
The type plate is located on the bottom of the set.
CAUTION
Use of controls or adjustments or per formance of
procedures other than here in may result in haz ard ous
radi a tion exposure or other unsafe operation.
Notice
This product complies with the radio interference requirements of the
EuropeanCommunity.
This product complies with the requirements of the following directives
andguidelines:2004/108/EC+2006/95/EC
Anychangesormodicationsmadetothisdevicethatarenotexpressly
approvedbyPhilipsConsumerLifestylemayvoidtheuser’sauthorityto
operate the equipment.
Recycling
Your product is designed and manufactured with high quality materials
and components, which can be recycled and reused.
When you see the crossed-out wheel bin symbol attached to a
product,itmeanstheproductiscoveredbytheEuropeanDirective
2002/96/EC:
Never dispose of your product with other household waste. Please
inform yourself about the local rules on the separate collection of
electrical and electronic products. The correct disposal of your old
product helps prevent potentially negative consequences on the
environment and human health.
YourproductcontainsbatteriescoveredbytheEuropeanDirective
2006/66/EC,whichcannotbedisposedofwithnormalhouseholdwaste.
When you see the crossed-out wheel bin symbol with the chemical
symbol ‘Pb’, it means that the batteries comply with the requirement
set by the directive for lead:
Pb
Please inform yourself about the local rules on separate collection of
batteries. The correct disposal of batteries helps prevent potentially
negative consequences on the environment and human health.
Environmental information
All unnecessary packaging has been omitted. We have tried to make the
packaging easy to separate into three materials: cardboard (box), polysty-
rene foam (buffer) and polyethylene (bags, protective foam sheet.)
Your system consists of materials which can be recycled and reused if
disassembled by a specialized company. Please observe the local regula-
tions regarding the disposal of packaging materials, exhausted batteries
and old equipment.
AE2160_05.indd 1 2009-04-24 10:36:06 AM