S231C4 www.philips.
Table of Contents 1. For Your Safety .......................................1 1.1 1.2 1.3 1.4 Precautions.........................................................1 Cleaning ...............................................................2 Special notes on SMART All-in-One ..2 Disposal of product and packing material ................................................................3 2. Setting up the monitor .........................4 2.1 2.2 2.3 2.4 Installation ............................................
1. For your safety 3. The manufacturer is not responsible for any radio or TV interference caused by unauthori]ed modiÀcation to this equipment. It is the responsibilities of the user to correct such interference. 1. For Your Safety Before operating the SMART All-in-One, please read this manual thoroughly. This manual should be retained for future reference.
1. For your safety Manufacturer: SHENZHZEN HONOR ELECTRONIC CO., LTD. The SMART All-in-One is equipped with a three-pronged grounded plug, a plug with a third (grounding) pin. This plug will fit only into a grounded power outlet as a safety feature. If your outlet does not accommodate the three-wire plug, have an electrician install the correct outlet, or use an adapter to ground the appliance safely. Do not defeat the safety purpose of the grounded plug.
1. For your safety Taking back/Recycling Information for Customers 1.4 Disposal of product and packing material Philips establishes technically and economically viable objectives to optimize the environmental performance of the organization's product, service and activities. Waste Electrical and Electronic EquipmentWEEE From the planning, design and production stages, Philips emphasizes the important of making products that can easily be recycled.
2. Setting up the monitor 2. Setting up the monitor To keep the SMART All-in-One looking new, periodically clean it with a soft cloth. Stubborn stains may be removed with a cloth lightly dampened with a mild detergent solution. Never use strong solvents such as thinner, benzene, or abrasive cleaners, since these will damage the cabinet. As a safety precaution, always unplug the SMART All-in-One before cleaning it. Do not scratch the screen with hard things, it may cause permanent damage.
2. Setting up the monitor Connection Insert your SD card 1. Disconnect the power cord. 2. Insert your SDHC card to the card slot. Connect for VGA/HDMI input 11 10 9 8 7 6 8 5 1. Connect with VGA or HDMI cable from your PC or AV device to SMART All-in-One. 4 3 2 2. Connect power cord to SMART All-in-One Àrmly and press the power button on. 1 3. The SMART All-in-One turns on and enters the previous source input selected. 4. Press the input button HDMI source.
2. Setting up the monitor Adjusting viewing angle 2.2 Operating the monitor For optimal viewing, it is recommended to look at the full face of the SMART All-in-One, then adjust the SMART All-in-One’s angle to your own preference. SMART All-in-One allows you to either use it as a stand-alone SMART All-in-One in Android system without any PC connection required, or as a normal PC monitor when connecting with PC. The SMART All-in-One's tilted angle is adjustable from 12° to 57.5°. 12° Front control 57.
2. Setting up the monitor 1 2 3 4 5 6 7 8 What is On-Screen Display (OSD)? Press to turn SMART All-in-One’s power ON or OFF. Press to access the OSD menu for VGA and HDMI input. On-Screen Display (OSD) is a feature in all Philips SMART All-in-One. It allows user to adjust screen performance or to select functions of the monitor directly through an on-screen instruction window. In the OSD menu, press to conÀrm the OSD adjustment. In the OSD menu, adjust the OSD menu.
2. Setting up the monitor The OSD menu tree 2.3 Detach the hinge for VESA Here is an overall view of the OSD structure for your reference to work your way around the different adjustments. Main menu Input Picture Audio Color Language OSD Settings Setup Before you start detaching the hinge, please follow the instructions below to avoid any possible damage or injury. Sub menu 1. Place the monitor face down on a smooth surface. Pay attention not to scratch or damage the screen.
2. Setting up the monitor Note This monitor accepts a 75mm x 75mm VESACompliant mounting interface.
2. Setting up the monitor 2.4 SMART All-in-One Operation Philips SMART All-in-One bundles with Android system which applies touch panel technology for users to use it as a stand-along PC. It does not require any PC connections and can be controlled with Àgures ² touching the panel for selection and conÀrmation.To enter the Android Home screen, press the hotkey on the front bezel, and select Android as the input source. 2.4-1 Home screen The Home screen is composed of Àve screen panels.
2. Setting up the monitor 2.4-2 Customizing your Home Screen Adding application icons, shortcuts, or widgets to the home screen as your preference. You can also change the wallpaper. Add an item to the Home Screen: 1. Tap on the icon in the ststem bar to enetr the APPS gallery screen. 2. Select [APPS] or [WIDGETS]. 3. Tap and hold the item until it enlarged. Drag the item to the place you preferred on the Home Screen. Move an item on the Home Screen: 1. tap and hold the item until it enlarged. 2.
2. Setting up the monitor 2.4-3 Google Search 1. Click on the icon in the Home screen. The on-screen keyboard displayed. 2. Type a keyword or text in the URL box. As you type, the search results that fully or partially match the text being typed appear. 3. Scroll the listed search results and clcik the desired result. 4. The matching application or the browser with matching web links opens. 5. Click the desired link if you want to view a web page.
2. Setting up the monitor 2.4-4 APPS Gallery 1. Click on the icon in the system bar to enter the APPS gallery screen. 2. Click on the application icon to open it. icon to return to the Home Screen, or click on the 3. Click on the the previous screen.
2. Setting up the monitor 2.4-5 Android system settings in the central Android Home screen. Click the icon Settings Main Menu Sub Menu Item Description WIRELESS & NETWORKS Wi-Fi Set up Wi-Fi Bluetooth Bluetooth settings Ethernet Ethernet conÀguration More Set up VPN & portable hotspot Sound Set the volume level. Display Set the wallpaper, sleep timer, and font size for the SMART All-in-One. Storage Display the storage information. Apps Manage the Apps installed.
2. Setting up the monitor SYSTEM Date & time Set up the system date and time. Accessibility Developer options The internet data is used after clicking the option About Display the information for the SMART All-in-One. Note The graphics are for illustration purpose only, they may differ depanding on the countries. Please refer to the actual products.
3. Image Optimization 4. When SmartImage is enabled, the sRGB scheme is disabled automatically. To use sRGB, you need to disable select {Off} for the SmartImage. There are seven modes to select: Text, OfÀce, Photo, Movie, Game, Economy and Off. 3. Image Optimization What is it? SmartImage provides presets that optimize display for different types of content, dynamically adjusting brightness, contrast, color and sharpness in real time.
3. Image Optimization Game: Turn on over drive circuit for best response time, reduce jaggy edges for fast moving objects on screen, enhance contrast ratio for bright and dark scheme, this profile delivers the best gaming experience for gamers. Economy: Under this profile, brightness, contrast are adjusted and backlighting finetuned for just right display of everyday office applications and lower power consumption. Off: No optimization by SmartImage.
7HFKQLFDO 6SHFLÀFDWLRQV 4. Technical Specifications Picture/Display LCD Panel Type Backlight Type Panel Size Effective Viewing Area Aspect Ratio Optimum Resolution Response Time (Typ.) IPS WLED system 23 inch / 58.4 cm 509.184 (H) x 286.
7HFKQLFDO 6SHFLÀFDWLRQV Other Convenience Plug & Play Compatibility LAN Speed RF Module M/N Stand Tilt Power On Mode Monitor Standby Mode Android Standby Mode Off Mode Power LED Indicator Power Supply Dimensions Product with Stand Product with Packaging Weight Product with Stand Product with Packaging Operating conditions Temperature Range (operation) Temperature Range (storage) Relative Humidity MTBF Sustainability Environmental and Energy Recyclable Packaging Material Compliance and standards Regulato
7HFKQLFDO 6SHFLÀFDWLRQV 4.1 Resolution & Preset PC Modes Maximum Resolution 1920x1080@60Hz (analog input) 1920x1080@60Hz (digital input) Recommended Resolution 1920x1080@60Hz (digital input) H. freq (kHz) Resolution V. freq (Hz) 31.47 720x400 70.09 31.47 640x480 59.94 35.00 640x480 66.67 37.86 640x480 72.81 37.50 640x480 75.00 37.88 800x600 60.32 46.88 800x600 75.00 48.36 1024x768 60.00 60.02 1024x768 75.03 63.89 1280x1024 60.02 79.98 1280x1024 75.03 55.
5. Regulatory Infomation Adjustability for user comfort (displays, headsets) Acoustic performance ² protection against sound spikes (headsets) and fan noise (projectors, computers) Ergonomically designed keyboard (notebooks) 5. Regulatory Information 7&2 &HUWLÀHG Congratulations! Electrical Safety, minimal electro-magnetic Emissions Third Party Testing All certiÀed product models have been tested in an independent, accredited laboratory.
5. Regulatory Infomation EPEAT EN61000-3-3:2008 (Limitation of Voltage Fluctuation and Flicker) following provisions of directives applicable. EN50581:2012 (Technical documentation for the assessment of electrical and electronic products with respect to the restriction of hazardous substances) 2006/95/EC (Low Voltage Directive). 2004/108/EC (EMC Directive). 2009/125/EC (ErP Directive, EC No. 1275/2008 Implementing Directive for Standby and Off mode power consumption).
5. Regulatory Infomation Federal Communications Commission (FCC) Notice (U.S. Only) Changes or modiÀcations not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
5. Regulatory Infomation EN 55022 Compliance (Czech Republic Only) Cependant, rien ne peut garantir l'absence d'interférences dans le cadre d'une installation particulière. Si cet appareil est la cause d'interférences nuisibles pour la réception des signaux de radio ou de télévision, ce qui peut être décelé en fermant l'équipement, puis en le remettant en fonction, l'utilisateur pourrait essayer de corriger la situation en prenant les mesures suivantes: Réorienter ou déplacer l’antenne de réception.
5. Regulatory Infomation North Europe (Nordic Countries) Information Ergonomie Hinweis (nur Deutschland) Der von uns gelieferte Farbmonitor entspricht den in der "Verordnung über den Schutz vor Schäden durch Röntgenstrahlen" festgelegten Vorschriften. Placering/Ventilation VARNING: FÖRSÄKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG ÄR LÄTÅTKOMLIGA, NÄR DU STÄLLER DIN UTRUSTNING PÅPLATS.
5. Regulatory Infomation China RoHS EU Energy Label The People's Republic of China released a regulation called "Management Methods for Controlling Pollution by Electronic Information Products" or commonly referred to as China RoHS. All products produced and sold for China market have to meet China RoHS request. ѝഭ⭥ᆀؑӗ૱⊑ḃ᧗ࡦḷ䇶㾱≲ ѝഭ RoHS⌅㿴ḷ⽪㾱≲ ӗ૱ѝᴹ∂ᴹᇣ⢙䍘ᡆ ݳ㍐Ⲵ〠৺ਜ਼䟿 ᴹ∂ᴹᇣ⢙䍘ᡆݳ㍐ 䜘Ԧ〠 The European Energy Label informs you on the energy efÀciency class of this product.
5.
5. Regulatory Infomation USA Radiation Exposure Statement: Federal Communication Commission Interference Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This device complies with Part 15 of the FCC Rules.
5. Regulatory Infomation Avertissement: “Este equipamento opera em caráter secundário, isto é, nmo tem direito a proteomo contra interferência prejudicial, mesmo de estao}es do mesmo tipo, e nmo pode causar interferência a sistemas operando em caráter primário.
5.
6. Customer care and warranty Pixels and Sub pixels 6. Customer care and warranty A pixel, or picture element, is composed of three sub pixels in the primary colors of red, green and blue. Many pixels together form an image. When all sub pixels of a pixel are lit, the three colored sub pixels together appear as a single white pixel. When all are dark, the three colored sub pixels together appear as a single black pixel.
6. Customer care and warranty Proximity of Pixel Defects Two adjacent lit sub pixels: - Red + Blue = Purple - Red + Green = Yellow - Green + Blue = Cyan (Light Blue) Because pixel and sub pixels defects of the same type that are near to one another may be more noticeable, Philips also speciÀes tolerances for the proximity of pixel defects. Three adjacent lit sub pixels (one white pixel).
6. Customer care and warranty Pixel Defect Tolerances In order to qualify for repair or replacement due to pixel defects during the warranty period, a TFT Monitor panel in a Philips Áat panel monitor must have pixel or sub pixel defects exceeding the tolerances listed in the following tables.
6. Customer care and warranty 6.2 Customer Care & Warranty For warranty coverage information and additional support requirement valid for your region, please visit www.philips.com/support website for details. You may also contact your local Philips Customer Care Center number listed below. Contact Information for WESTERN EUROPE region: Country CSP Hotline Number Price Opening Hours Austria RTS +43 0810 000206 € 0.07 Mon to Fri : 9am - 6pm Belgium Ecare +32 078 250851 € 0.
6. Customer care and warranty Contact Information for CENTRAL AND EASTERN EUROPE region: Country Call Center CSP Consumer Care Number Belarus N/A IBA +375 17 217 3386 +375 17 217 3389 Bulgaria N/A LAN Service +359 2 960 2360 Croatia N/A MR Service Ltd +385 (01) 640 1111 Czech Rep.
6. Customer care and warranty Contact Information for APMEA region: Country ASP Consumer Care Number Opening Hours Australia AGOS NETWORK PTY LTD 1300 360 386 Mon.~Fri. 9:00am-5:30pm New Zealand Visual Group Ltd. 0800 657447 Mon.~Fri. 8:30am-5:30pm Hong Kong Macau Company: Smart Pixels Technology Ltd. Hong Kong: Tel: +852 2619 9639 Macau: Tel: (853)-0800-987 Mon.~Fri. 9:00am-6:00pm Sat. 9:00am-1:00pm India REDINGTON INDIA LTD Tel: 1 800 425 6396 SMS: PHILIPS to 56677 Mon.~Fri.
7. Troubleshooting & FAQs AUTO button doesn't function 7. Troubleshooting & FAQs 7.1 Troubleshooting This page deals with problems that can be corrected by a user. If the problem still persists after you have tried these solutions, contact Philips customer service representative. Note The Auto Function is not applicable in DVIDigital mode as it is not necessary.
7. Troubleshooting & FAQs +RUL]RQWDO ÁLFNHU DSSHDUV Image appears distorted. Text is fuzzy or blurred. Set the PC’s display resolution to the same mode as monitor’s recommended screen native resolution. Adjust the image using the “Auto” function in OSD Main Controls. Green, red, blue, dark, and white dots appears on the screen Eliminate the vertical bars using the Phase/ Clock of Setup in OSD Main Controls. It is valid only in VGA mode.
7. Troubleshooting & FAQs Turn on your monitor and then turn on your PC. Q2: What is the recommended refresh rate for SMART All-in-One? Ans.: Recommended refresh rate in SMART All-in-One is 60Hz, In case of any disturbance on screen, you can set it up to 75Hz to see if that removes the disturbance. 4 :KDW DUH WKH LQI DQG LFP ÀOHV RQ WKH CD-ROM? How do I install the drivers (.inf and .icm)? Ans.: These are the driver Àles for your monitor.
7. Troubleshooting & FAQs Note A measurement of the color of light radiated by an object while it is being heated. This measurement is expressed in terms of absolute scale, (degrees Kelvin). Lower Kevin temperatures such as 2004K are red; higher temperatures such as 9300K are blue. Neutral temperature is white, at 6504K. Q9: Can I connect my SMART All-in-One to any PC, workstation or Mac? Ans.: Yes. All Philips SMART All-in-One are fully compatible with standard PCs, Macs and workstations.
7. Troubleshooting & FAQs Q4: How can I use it as a multi-OS display? Ans.: This SMART All-in-One is powered by built-in Android system and therefore is a stand-alone product on its own without any additional requirement. Additionally, it is also equipped with a standard VGA / HDMI connector. This enables it to also operate as a standard desktop monitor, while connected your standard notebook or desktop computer. Your PC may have OS of your choice.
© 2013 Koninklijke Philips N.V. All rights reserved. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license from Koninklijke Philips N.V.
