S5000 series www.philips.
1 2 16 17 18 19 20 21 3 4 13 14 11 12 5 6 7 8 9 10 15
6 English Contents Introduction_______________________________________________________ General description_______________________________________________ What do the icons on my appliance handle mean?_____________ What does the icon on my Quick Clean Pod mean?_____________ How do I charge my appliance?__________________________________ Charging with the supply unit____________________________________ Charging in the charging stand (specific models only)__________ 'Unplug for use' symbol __________________
English 7 General description 1 Pop-up trimmer 2 Trimmer release slide 3 Shaving unit 4 Shaving unit release button 5 On/off button 6 Handle 7 Socket for small plug 8 Charging stand 9 Supply unit 10 Small plug 11 Protection cap 12 Pouch 13 Philips Quick Clean Pod cartridge 14 Quick Clean Pod 15 Cleaning brush 16 Length settings 17 Click-on beard styler attachment 18 Comb for beard styler attachment 19 Attachment holder 20 Click-on cleansing brush attachment 21 Click-on nose trimmer attachment Note: The ac
8 English What do the icons on my appliance handle mean? Icon Behavior Meaning Flashing slowly when you remove the shaver from the Quick Clean Pod during the cleaning programa The cleaning program was interrupted. If you put the shaver back into the Quick Clean Pod within four seconds, the cleaning program resumes automatically. Flashing Clean the shaver in the Quick Clean Pod (see 'How do I use the Quick Clean Pod?').
English Icon 9 Behavior Meaning Lights up when you pick up the appliance The number of bars lit up show the remaining battery charge. Bottom light flashing orange The battery is almost empty (see 'How do I charge my appliance?'). Lights flashing in sequence The appliance is charging. Lights up The appliance is fully charged. continuously Flashing The appliance must be disconnected from the wall socket before you can switch it on (see 'How do I charge my appliance?').
10 English Quick Charge: After approx. 5 minutes of charging, the battery contains enough energy for one shave. When the appliance is fully charged it has a cordless operating time of up to 60 minutes. Note: You cannot use the appliance while it is charging. Charging with the supply unit 1 Make sure that the appliance is switched off. 2 Insert the small plug into the appliance and put the supply unit in the wall socket.
English 11 2 Put the small plug in the charging stand and put the supply unit in the wall socket. 3 Place the appliance in the charging stand. Specific models only: The light ring on the bottom of the charging stand lights up and rotates quickly. - After approximately 5 minutes, the light ring rotates slower. The battery now contains enough energy for one shave. - As the appliance continues to charge, the light ring becomes brighter and rotates slower.
12 English the tap. For safety reasons, the appliance can therefore only be used without cord. Shaving You can use this appliance either wet or dry, or even under the shower. For a wet shave, apply some water and shaving foam or gel to your skin and rinse the shaving heads under the tap with warm water before following the steps below. 1 Switch on the appliance. 2 Move the shaving heads over your skin in circular movements to catch all hairs growing in different directions.
English 13 Note: Make sure you rinse all foam or shaving gel off the appliance. Skin adaptation period Your first shaves may not bring you the result you expect and your skin may even become slightly irritated. This is normal. Your skin and beard need time to adapt to any new shaving system. To allow your skin to adapt to this new appliance, we advise you to shave regularly (at least 3 times a week) and exclusively with this appliance for a period of 3 weeks.
14 English 3 Hold the trimmer perpendicular to the skin and move the appliance downwards while you exert gentle pressure. 4 You can also use the trimmer under your nose. 5 Switch off the appliance and clean the trimmer after each use to prevent clogging and damage (see 'How do I clean my appliance and the attachments?'). 6 Close the trimmer. Using the click-on attachments Note: The accessories supplied may vary for different products.
English 15 2 Slide the comb straight into the guiding grooves on both sides of the beard styler attachment. 3 Press the length selector and then push it to the left or right to select the desired hair length setting. 4 Switch on the appliance. 5 Move the appliance upwards while you exert gentle pressure. Make sure the front of the comb is in full contact with the skin. 6 Switch off the appliance and clean the attachment after use.
16 English 3 Hold the beard styler attachment perpendicular to the skin and move the appliance downwards while you exert gentle pressure. 4 Switch off the appliance and clean the attachment after use. Using the nose/ear trimmer attachment You can use the nose/ear trimmer attachment to trim your nose and/or ear hair. Trimming nose hair Make sure both the nose/ear trimmer attachment and nasal passages are clean before trimming.
English 17 2 Slowly move the trimming head along the rim of the ear to remove hairs that stick out beyond the rim. 3 Carefully insert the trimming head into the outer ear channel. Do not insert the trimming head more than 0.5 cm into your ear channel, as this could damage the eardrum. 4 Slowly turn the trimming head around to remove all unwanted hairs from your outer ear channel. 5 Switch off the appliance and clean the attachment after use.
18 English Once the travel lock is deactivated, the appliance switches on automatically. Note: The shaver unlocks automatically when it is connected to a wall socket. How do I clean my appliance and the attachments? Clean the appliance and the attachments after each use for optimal performance. Cleaning the shaver under the tap Clean the shaver after each use to prevent clogging and damage. Never dry the shaving unit with a towel or tissue, as this may damage the shaving heads.
English 19 4 Rinse the hair chamber under a warm tap. 5 Rinse the shaving head holder under a warm tap. 6 Carefully shake off excess water and let the shaving head holder air-dry completely. 7 Close the shaving unit. Thorough cleaning We advise you to clean the shaving heads thoroughly once a month or when the shaver does not shave as well as it used to. 1 Make sure that the appliance is switched off and disconnected from the wall socket.
20 English 3 Rinse the hair chamber and shaving head holder under the tap. 4 Remove the shaving heads. For detailed instructions, see 'How do I replace the shaving heads?.' Note: Do not clean more than one cutter and guard at a time, since they are all matching sets. If you accidentally put a cutter in the wrong shaving guard, it may take several weeks before optimal shaving performance is restored. 5 Clean the cutter and guard under the tap. 6 Shake off excess water.
English 21 3 Switch on the appliance and rinse the pop-up trimmer with warm water. 4 After cleaning, switch off the appliance. 5 Carefully shake off excess water and let the pop-up trimmer air dry. 6 Close the trimmer. Tip: For optimal performance, lubricate the teeth of the pop-up trimmer with a drop of mineral oil every six months (oil not included). Cleaning the click-on attachments Never dry the trimmer or beard styler attachments with a towel or tissue, as this may damage the trimming teeth.
22 English 4 Carefully shake off excess water from the beard styler, combs and nose/ear trimmer attachments and let them air dry completely. Dry the cleansing brush attachment with a towel. Never dry the cutting unit with a towel or tissue, as this may damage the trimming teeth. Tip: For optimal performance, lubricate the teeth of the beard styler attachment with a drop of sewing machine oil regularly.
English 23 4 Press the small circular piece on the handle of the Quick Clean Pod Cartridge to break the snap hook on the handle. 5 Place the Quick Clean Pod Cartridge into the Quick Clean Pod. 6 Put the top of the Quick Clean Pod back onto the base and turn it clockwise until you hear a click. Do not tilt the Quick Clean Pod to prevent leakage.
24 English Always shake excess water off the shaver before you place it in the Quick Clean Pod. 1 Place the shaver upside down into the Quick Clean Pod. The shaver automatically detects that it is in the Quick Clean Pod. 2 Switch on the shaver to start the cleaning program. Each cleaning program takes approximately one minute. During the cleaning program the cleaning symbol lights up continuously and the blue icon pulses. The shaver handle vibrates twice quickly when the cleaning program is finished.
English 1 25 Twist and remove the top of the Quick Clean Pod. 2 Lift the Quick Clean Pod Cartridge out of the Quick Clean Pod by the handle. 3 Pour any remaining fluid down a drain and recycle the empty cartridge in accordance with local waste regulations. 4 Place a new Quick Clean Pod Cartridge into the Quick Clean Pod (see 'Preparing the Quick Clean Pod for use'). Scan the QR code to the left or visit www.philips.com/cleaning-cartridge to order replacement Quick Clean Pod Cartridges.
26 English 2 Press the release buttons on the shaving unit and pull the shaving head holder off the shaving unit. 3 Turn the retaining rings anticlockwise and remove them. Place them aside in a safe place. 2 1 4 Remove the shaving heads from the shaving head holder. Discard the used shaving heads immediately to avoid mixing them with the new shaving heads. 5 Place new shaving heads in the holder.
English 27 - Each retaining ring has two recesses that fit exactly into the projections of the shaving head holder. Turn the ring clockwise until your hear a click to indicate that the ring is fixed. Note: Hold the shaving head holder in your hand when you reinsert the shaving heads and reattach the retaining rings. Do not place the shaving head holder on a surface, as this may cause damage to the shaving heads.
28 English Troubleshooting This chapter summarizes the most common problems you could encounter with the appliance. If you are unable to solve the problem with the information below, visit www.philips.com/support for a list of frequently asked questions or contact the Consumer Care Center in your country. Shaver Problem Possible cause Solution The appliance does not work when I press the on/off button.
English Problem Possible cause Solution Water is leaking from the bottom of the appliance. During cleaning, water may collect between the inner body and the outer shell of the appliance. This is normal and not dangerous because all electronics are enclosed in a sealed power unit inside the appliance. 29 Philips Quick Clean Pod Problem Possible cause My shaver isn't clean You removed the after using the Philips shaver before the Quick Clean Pod. cleaning program was finished.
30 English My Philips Quick Clean Pod is overflowing. You regularly use the Philips Quick Clean Pod after rinsing the shaver but not shaking off excess water. Shake off excess water after rinsing the shaving heads each time before putting the shaver into the Philips Quick Clean Pod. You shaved with shaving gel or foam and did not rinse the shaver before using the Philips Quick Clean Pod. Rinse the shaving heads thoroughly before using the Philips Quick Clean Pod (see 'Using the Quick Clean Pod').
© 2020 Koninklijke Philips N.V. All rights reserved 3000.057.1977.
