User manual

ENGLISH
Important
For your child‘s safety and
health
WARNING!
- Always use this product with adult
supervision.
- Never use feeding teats as a soother.
- Continuous and prolonged sucking of
uids will cause tooth decay.
- Always check food temperature before
feeding.
- It is not recommended to use a
microwave to warm up baby‘s food
or drinks. Microwaves might alter the
quality of food/drinks and destroy
some valuable nutrients and it may
produce localized high temperatures.
Therefore, take extra care if and when
you heat up food in a microwave.
When heating up liquid or food in
the microwave, please only place the
container without screw ring, teat and
cap. Always stir heated food to ensure
even heat distribution and check the
temperature before serving.
- Keep all parts not in use out of the
reach of children.
- Do not allow child to play with small parts
or walk/run while using bottles or cups.
- Do not place in a heated oven.
- Drinks other than milk and water, such as
fruit juices and avoured sugary drinks are
not recommended. If they are used, they
should be well diluted and only used for
limited periods, not constantly sipped.
- Do not use abrasive cleaning agents
or antibacterial cleaners. Do not place
components directly on surfaces that
have been cleaned with anti-bacterial
cleaners.
- Expressed breast milk can be stored
in sterilized Philips Avent bottles/
containers in the refrigerator for up
to 48 hours (not in the door) or in
the freezer for up to 3 months. Never
refreeze breast milk or add fresh breast
milk to already frozen milk.
- Always discard any breast milk that is
left over at the end of a feed.
- Plastic material properties may be aected
by sterilizing and high temperatures. This
can aect the t of the cap.
- Throw away any part at the rst signs
of damage or weakness.
- Do not alter the product or parts of it
in any way. This may result in unsafe
functioning of the product.
Teat
- Inspect before each use and pull the
feeding teat in all directions. Throw away
at the rst signs of damage or weakness.
- For hygiene reasons, we recommend
replacing teats after 3 months.
- Keep teats in a dry, covered container.
- Do not leave a feeding teat in direct
sunlight or heat, or leave in disinfectant.
Before rst use
- Before rst use, disassemble all parts,
clean and sterilise the product.
- Clean to ensure hygiene by washing
and rinsing all parts thoroughly.
- Sterilise by using a Philips Avent
sterilizer or boil all parts for 5 minutes.
This is to ensure hygiene.
- During sterilising with boiling water,
prevent the bottle or other parts from
touching the side of the pan. This can
cause irreversible product deformation
or damage that Philips cannot be held
liable for.
- Inspect the feeding teat before use and
pull the feeding teat in all directions.
Do not use damaged products.
Cleaning
- After every use, take all items apart,
wash in warm soapy water and rinse
thoroughly. Make sure that you wash
your hands thoroughly and that the
surfaces are clean before contact with
sterilised components.
- Excessive combinations of detergents
may eventually cause plastic
components to crack. Should this
occur, replace immediately.
- Dishwasher safe. Food colorings may
discolor components.
- When not in use, do not store in
sunlight or heat, or leave in disinfectant
(‚sterilizing solution‘) for longer than
recommended, as this may weaken the
teat. Do not place in a heated oven.
- Clean and sterilize all parts before
each use.
Assembly
When you assemble the bottle, make sure
you place the cap vertically onto the bottle
so that the teat sits upright (see image
for more details). The teat is easier to
assemble if you wriggle it upwards instead
of pulling it up in a straight line.
Maintenance
- Before each use, inspect all items.
Pull the feeding teat in all directions.
- Throw away any part at the rst signs
of damage or weakness.
- For hygiene reasons, we recommend
replacing teats after 3 months.
- Keep teats in a dry, covered container.
- When not in use, do not leave in
sunlight or heat, or leave in disinfectant
(‚sterilising solution‘) for longer than
recommended, as this may weaken the
teat. Do not place in a heated oven.
Choosing the right teat for
your baby
The Philips Avent teats are available with
dierent ow rates to help your baby
with drinking. Over time you can change
the teat accommodating the individual
needs of your baby. Philips Avent teats are
clearly numbered on the side to indicate
ow rate (see image). Make sure you use
a teat with the correct ow rate when you
feed your baby. Use a lower ow rate if
your baby chokes, is leaking milk or has
trouble adjusting to the drinking speed.
Use a higher ow rate if your baby falls
asleep during feeding, gets frustrated or
when feeding takes a very long time.
Teats are made of silicone and available for
0m+, 1m+, 3m+, 6m+, variable ow (I/II/III)
and thick feed (Y).
(1) The teat for 0m+ is ideal for newborn
and breastfed babies of all ages. The teat
has only one opening for uid and the
number 1 is shown on the teat.
1 2
3 4
5 6
1 2
3
© 2019 Koninklijke Philips Electronics N.V.
All rights reserved.
4213.354.4323.2 (05/2019)
>75% recycled paper
www.philips.com/avent
Philips Consumer Lifestyle BV
Tussendiepen 4, 9206 AD Drachten,
Netherlands
Trademarks owned by the Philips Group.