Screeneo U4 User Manual Ultra Short Throw Projector Register your product and get support at www.philips.
Table of contents Introduction �������������������������������������������������3 Dear customer ���������������������������������������������������������������3 5 Connect to external speakers or headphones ������������������������������������������11 About this user manual ����������������������������������������������3 Cable connection ��������������������������������������������������������11 What’s in the box ����������������������������������������������������������3 Bluetooth connection ����������
Introduction What’s in the box Dear customer b Remote control with 2 AAA batteries Thank you for purchasing this projector. d Quick Start Guide with Warranty Card We hope you enjoy this product and the many functions it offers! About this user manual a Screeneo U4 projector (SCN350/INT) c HDMI™ to HDMI™ cable e AC adapter f AC power cables with plugs x 3 a b d c The quick start guide supplied with this product allows you to start using this product quickly and easily.
1 General safety information Take note of all warning and safety notes indicated. Do not make any changes or settings that are not described in this user manual. Incorrect operation, and improper handling can lead to physical injury, damage to the product or loss of data. Setting up the product This product is for indoor use only. Place the product securely on a stable, flat surface.
Power supply Use only a power adapter which is certified for this product (see Technical data, page 21). Check whether the mains voltage of the power supply matches the mains voltage available at the setup location. This product complies with the voltage type specified on the product. 2 Overview Rear view a b The power outlet shall be installed near the product and shall be easily accessible. CAUTION! USB-A HDMI 2 (ARC) Always use the projector off.
Top view Remote control j a b c d a e f k g l m b h i a Projection lens b • • • • Switch the projector on or to standby mode. When the projector is on, the LED lights up in white. When the projector is in standby mode, the LED lights up in red. When the projector is in Bluetooth speaker mode, the LED lights up in blue. a Switch to a different input source. b Adjust the focus automatically or manually. c OK Confirm a selection on the screen.
j Switch the projector on or to standby. k Return to the previous screen or exit the current screen. 3 Initial setup Notice Make sure all devices are disconnected from their power supplies before establishing or changing any connections. l Mute the speakers. m Toggle between different brightness modes. Place the projector 1 Place the projector on a flat surface such as a table in front of the projection surface. This is the most common way to position the projector for quick setup and portability.
4 Connect the power cable to an electrical socket. • • The power LED on the projector lights up in red. When using a remote control with infrared signals, point the remote control at the IR sensor on the projector, and make sure there is no obstacle between the remote control and the IR sensor. Power on and set up the projector c Power on/off the projector • b a d • Prepare the remote control CAUTION! The improper use of batteries can lead to overheating, explosion, risk of fire and injury.
Image focus adjustment You can let the projector automatically adjust the image focus for you or adjust it manually. • • To automatically adjust the image focus, press on the remote control. To manually adjust the image focus, press or on the remote control. Image shape adjustment Screen size adjustment The projection screen size (or size of images) is determined by the distance between the lens of the projector and the projection surface. This projector has a projection distance of 4 cm to 30.
4 Connect to playback devices Notice Make sure all devices are disconnected from their power supplies before establishing or changing any connections. Connect to devices through HDMI™ You can connect a playback device (e.g. a Bluray player, gaming console, camcorder, digital camera or PC) to the projector through HDMI™ connection. With this connection, images are shown on the projection screen, and audio is played on the projector.
Connect to a dongle You can connect a dongle (e.g. Amazon Fire Stick, Roku Stick or Chromecast) to the projector to easily watch videos over the internet. With this connection, images are shown on the projection screen, and audio is played on the projector. 1 Connect a dongle to the projector's HDMI 2 (ARC) port using an HDMI™ cable. 2 Connect the dongle to the projector's USB-A port using a USB cable.
Bluetooth connection Also, its power LED blinks in light blue. When the pairing is complete, the projector briefly displays "Paired successfully" on the screen, as well as the name of the paired device. Also, its power LED turns solid light blue. • If no pairing is created, the projector will automatically exit pairing mode in 10 seconds. To pair a second Bluetooth speaker or set of headphones, repeat steps 2 and 3 above but press the other button in step 3.
6 Media playback The projector has an integrated media player. Using this media player, you can access and play video and audio files stored in the projector's internal memory or a USB storage device. Notice 3 Select Browsing from the left navigation pane, and then select and open the folder for the USB storage device, which is to the right of the Internal memory folder. 4 Select a media file. Note: Only supported media files are displayed on the screen.
7 Use the projector as a Bluetooth speaker 3 • You can use the projector as a Bluetooth speaker to output audio from Bluetooth playback devices such as smartphones, tablets and computers. Before you can use the projector with Bluetooth playback devices for the first time, you must pair the projector with them. The projector will automatically connect to a device as soon as they are paired.
Unpair a Bluetooth device This will remove the Bluetooth device from the projector's memory. You'll need to pair and connect this device to use it again. To unpair a Bluetooth device, press and hold either of the buttons on the projector for 5 seconds while the device is connected. The projector will announce "Disconnected" and reenter pairing mode after the unpairing.
• • • • • Audio Output: Select the projector's audio output type. Tip: You can more quickly switch between the internal speaker and Bluetooth output by pressing on the remote control. • Internal Speaker: Use the projector's internal speaker to output audio. • Bluetooth Output: Use the Bluetooth devices paired with the projector to output audio. • ARC: Use an HDMI™ ARC compatible device to output audio. CEC: Turn HDMI™ CEC (Consumer Electronics Control) on or off. The default value is ON.
Other settings You can view and change the following additional settings. 9 Maintenance Cleaning DANGER! Follow the following instructions when cleaning the projector: • • • • • • • 17 Language: Select the display language for the projector. Menu Position: Set the settings menu's position to Bottom Left, Top Left, Center, Bottom Right or Top Right. Image Calibration: Adjust the image by following the on-screen instructions.
CAUTION! Do not turn off the projector or remove the USB flash drive during a software update. Update software through USB 1 Visit www.philips.com/support, find your product (model number: SCN350/INT), open its support page and locate "Software & drivers". 2 Download the update package and unzip it if necessary. You should get an update file named "SCN350INT_firmware.zip". Copy this file to the root directory of a USB flash drive. Note: Do not unzip this file. 3 Turn on the projector if it is off.
10 Troubleshooting Power cycling If a problem occurs and you cannot resolve it using the instructions in this user manual, try the following steps to resolve the problem. 1 Turn the projector off by pressing 2 Wait at least 10 seconds. twice. 3 Turn the projector on by pressing and holding 4 If the problem persists, contact one of our customer service centres or your dealer. for 2 seconds. Problem Solution The projector cannot be turned on.
Problem Solution The projector does not react to remote control commands. • Check the batteries of the remote control. The temperature of the projector’s surface is warm. • For this projector it is normal to generate moderate heat during operation. The projector does not work after I connect • Check that the HDMI™ cable is plugged in it to a laptop. correctly. • Make sure that the laptop has been switched to projector display.
11 Appendixes Technical data Dimensions and weight Unpacked (W x D x H)..... 223.5 x 123.5 x 81.5 mm Packed (W x D x H)............... 267.5 x 187 x 148 mm Weight..................................................1.74 kg / 3.84 lb Technology/optical Display technology...........................................TI DLP Temperature requirements Light source......................... LED RGGB 4 channels Operating temperature.......................... 5 °C - 35 °C Colorimetry & metadata.......................
CE statement 15.105 Information to user. • The product shall only be connected to a USB interface of version USB 2.0 or higher. • Adapter shall be installed near the equipment and shall be easily accessible. • The operating temperature of the EUT can’t exceed 35°C and shouldn’t be lower than 5°C. • The plug is considered as disconnect device of adapter. • The UNII Band 5150-5250 MHz is for indoor use only. • The device complies with RF specifications when the device is used at 20 cm from your body.
RF Radiation Exposure statement: The device meets the exemption from the routine evaluation limits in section 2.5 of RSS102 and users can obtain Canadian information on RF exposure and compliance. This device should be installed and operated with a minimum distance of 7.8 inches (20 centimetres) between the device and your body. Other notice Preservation of the environment as part of a sustainable development plan is an essential concern of Screeneo Innovation SA.
Screeneo Innovation SA Route de Lully 5c - 1131 Tolochenaz - Switzerland Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license. Screeneo Innovation SA is the warrantor in relation to the product with which this booklet was packaged. Screeneo U4 2022 © Screeneo Innovation SA. All rights reserved.
