UpBeat SHB2505 用户手册 访问以下网站注册您的产品并获取支持 www.philips.
目录 1 重要安全说明 2 听力安全 2 一般信息 2 2 蓝牙无线耳机 3 包装盒内物品 3 其他设备 3 蓝牙无线耳机概述 4 3 使用入门 5 电池充电 5 首次将耳机与蓝牙设备配对 6 将耳机与另一个蓝牙设备配对 6 4 使用耳机 7 将耳机重新连接至蓝牙设备 7 开机/关机 7 管理通话和音乐 7 LED 指示灯状态 8 佩戴方式 8 5 耳机恢复出厂设置 6 技术数据 7 注意 符合性声明 9 10 11 11 旧产品和电池的处理 11 符合电磁场 (EMF) 法规 12 环保信息 12 法规遵循注意事项 12 8 常见问题解答 13 CN
1 重要安全说明 一般信息 为避免损坏或故障: 警告 听力安全 切勿将耳机置于高温环境 切勿摔落耳机。 切勿将耳机置于滴水或溅水环境下。 切勿将耳机没入水中。 切勿使用任何包含酒精、氨水、苯或研磨剂的清剂 清洁产品。 如果需要,请使用软布清洁产品,可用少量的水或 危险 稀释的中性肥皂水将布打湿进行清洁。 切勿将集成式电池置于高温环境,如阳光直射处、 为避免听力受损,应限制以高音量使用耳机的时 明火或类似环境。 间,并将音量设定在安全级别。音量越大,安全 如果电池更换不当,会有爆炸危险。仅使用相同或 收听的时间越短。 同等类型的电池进行更换。 使用耳机时请确保遵循以下准则。 • 在合理时间内以合理音量收听。 关于工作和存放状态下的温度以及湿度 • 听力适应后,注意不要持续地调高 • 音量。 • • 在有潜在危险的情况下应谨慎使用或 暂停使用。 • • 耳机声压过大可导致听力受损。 建议在驾车时不要双耳佩戴耳机,而 且在某些地区这样做将涉嫌违法。 • 90% 的环境中操作和存放产品。 请勿将音量调得太高而使得无法听见 周围的声音
2 蓝牙无线耳机 欢迎购买并使用 Philips 产品!若要充 USB 充电线(仅用于充电) 分享受 Philips 提供的支持,请访问 www.philips.
蓝牙无线耳机概述 麦克风 多功能键 LED 指示灯(耳机) Micro USB 充电端口 LED 指示灯(充电盒) CN
3 使用入门 • 充电过程可通过听筒上的白色 LED 指 • 耳机充满电后,白色指示灯熄灭。 示灯进行确认。 电池充电 注意 首次使用耳机之前,请将耳机放入充电盒中,并 为电池充电 3 个小时,这样可确保最佳的电池电 量和寿命。 仅限使用原装 USB 充电线,以免造成任何损坏。 连接耳机进行充电时会关闭耳机,因此请先结束 通话再为耳机充电。 充电盒 将 USB 充电线的一端连接到充电盒,另一 端连接到电源。 充电盒开始充电。 • • 提示 通常,耳机或充电盒充满电需要 2 个小时。 首次将耳机与蓝牙设备配对 确保耳机已充满电。 从充电盒中取出两个耳机,耳机将自 充电过程可通过前面板上的蓝色 LED 动开机,在连接左右耳机后,进入配 指示灯进行确认。 对模式。 充电盒充满电后,蓝色指示灯亮起。 提示 充电盒用作便携式备用电池为耳机充电。充电盒充 满电后,可为耳机提供 3 个完整充电周期的支持。 您会听到“开机”和“配对”的声音 提示。 耳机 将耳机放在充电盒中。 耳机开始充电。 CN
其中一个耳机 LED 指示灯闪烁 单耳机配对(单声道模式) 白光和蓝光。 从充电盒中取出耳机,听筒将自动开机。 耳机现在处于配对模式,可以与 右耳机会听到“开机”的声音提示。 蓝牙设备(例如手机)配对。 打开蓝牙设备的蓝牙功能。 将耳机与蓝牙设备配对。请参考蓝牙 设备的用户手册。 耳机发出“已连接”的声音提示, 打开设备的蓝牙功能,搜索“Philips SHB2505”,点击连接。(请参考第 6 页) LED 指示灯熄灭。可以使用设备播 放音乐或拨打电话。 Philips SHB2505 注意 开机后,如果耳机找不到之前连接的任何蓝牙设 备,它将自动切换到配对模式。 配对成功后,将听到“已连接”的声音 提示,且指示灯熄灭。 以下示例展示如何将耳机与蓝牙设备 配对。 打开蓝牙设备的蓝牙功能,选择 将耳机与另一个蓝牙设备 配对 Philips SHB2505。 提示后,请输入耳机密码“0000” (4 个零)。对于那些具有蓝牙 3.
4 使用耳机 将耳机连接至蓝牙设备 打开蓝牙设备的蓝牙功能。 从充电盒中取出两个耳机,耳机将自动 开机/关机 任务 打开耳机。 多功能键 操作 耳机 从充电盒 开机和重新连接。 中取出两 个耳机。 如果未连接任何设备,耳机将在 3 分钟后自动关闭。 将两个耳 关闭耳机。 机放入充 两个耳机现在均已打开,并自动 电盒中。 配对。 右/左耳机 耳机将搜索上次连接的蓝牙设备并 按住 5 秒钟。 与其自动重新连接。如果上次连接 白色 的设备不可用,耳机将搜索并重新 LED 指 连接至倒数第二个连接设备。 示灯闪烁 3 次。 提示 耳机不能同时连接到多个设备。如果您有两个配 对的蓝牙设备,请仅打开您要连接的设备的蓝牙 管理通话和音乐 功能。 如果在打开耳机后打开蓝牙设备的蓝牙功能, 则必须转到设备的蓝牙菜单,手动将耳机连接到 设备。 注意 如果耳机在 3 分钟内未能连接到任何蓝牙设备, 耳机将自动关闭以节省电池寿命。 在某些蓝牙设备中,可能不会自动连接。在这种 情况下,您必须转到设备的蓝牙菜单,手动将耳 机连接到蓝牙设备。 控制音乐 任务 多功能键
通话控制 任务 多功能键 操作 右/左耳机 按一次 拒接来电 右/左耳机 按住 2 秒钟 通话时切换 右/左耳机 按住 2 秒钟 接听/挂断 电池电量低 您会从耳机中听到 (耳机)。 “电池电量低”的 提示。 电话 白色 LED 指示灯每 3 分钟闪烁两次。 电池已充满电。 LED 指示灯熄灭。 来电 语音控制 任务 多功能键 操作 耳机状态下的电池 LED 指示灯 连接到耳机后,蓝牙设备上将显示电池 Siri/Google 右/左耳机 按两次 指示灯。 LED 指示灯状态 耳机状态 指示灯 耳机开机。 蓝色指示灯闪烁 3 次。 充电盒上的电池 LED 指示灯 耳机处于配对 蓝色和白色 LED 给耳机充电时,蓝色 LED 指示灯亮起。 模式。 指示灯闪烁。 耳机已打开但未连 蓝色和白色 LED 电量为 50%-75% 时,3 个蓝色 LED 指示灯亮起 接至蓝牙设备。 指示灯闪烁。如果 电量为 25%-50% 时,2 个蓝色 LED 指示灯亮起 无法建立连接,耳 电量为 0%-25% 时,1 个蓝色 LED 指示灯亮起
带 USB 充电线的充电盒上 的电池 LED 指示灯 5 耳机恢复出厂 设置 给耳机充电时,蓝色 LED 指示灯状态如下: 电量为 75-100% 时,4 个蓝色 LED 如果遇到任何配对或连接问题,可以按照以下 指示灯亮起 步骤将耳机恢复出厂设置。 电量为 50%-75% 时,2 个蓝色 LED 指示 灯亮起,第 3 个 LED 指示灯每秒闪烁一次 转到蓝牙设备的蓝牙菜单,从设备列表中 电量为 25%-50% 时,1 个蓝色 LED 指示 删除 Philips SHB2505。 灯亮起,第 2 个 LED 指示灯每秒闪烁一次 电量为 0%-25% 时,1 个蓝色 LED 指示 灯闪烁,每秒闪烁一次 关闭蓝牙设备的蓝牙功能。 将两个耳机放回充电盒。按住左右耳机功 能键 5 秒钟。 从充电盒中取出两个耳机,耳机将自动 开机。您会听到“开机”和“配对”的 声音提示。 然后,一个耳机 LED 指示灯闪烁白光 和蓝光,持续 3 分钟;另一个耳机 LED 指示灯熄灭。 佩戴方式 要将耳机与蓝牙设备配对,请打开蓝牙设 备的蓝牙功能,选择 Philips SHB2505。 CN
6 技术数据 耳机 音乐播放时间:5 小时(使用充电盒时 可延长使用 15 小时) 通话时间:5 小时(使用充电盒时可延 长使用 15 小时) 待机时间:80 小时 充电时间:2 小时 可充电锂电池:每个听筒 50 mAh 蓝牙版本:5.0 兼容的蓝牙配置协议: • HSP(免提配置协议 - HFP) • A2DP(高级音频传输协议) • AVRCP(音视频远程控制协议) 支持的音频编解码器:SBC 频率范围:2.
7 注意 符合性声明 拆除集成式电池 如果您所在的国家/地区未设立电子产品的收 集/回收系统,则请在处置耳机之前取出和回 MMD Hong Kong Holding Limited 特此 收电池以保护环境。 声明,本产品符合指令 2014/53/EU 中的 • 基本要求和其他相关规定。您可登录 在取出电池之前,确保已耳机已与充电 盒断开。 www.p4c.philips.
符合电磁场 (EMF) 法规 但是,无法保证在特定设施中不会发生干 扰。如果此设备确实对无线电或电视接收 本产品符合有关电磁场暴露的所有适用标准 产生有害干扰(可以通过关闭和打开设备 和法规。 来确定),则鼓励用户尝试通过以下一种 或多种措施来消除干扰: 环保信息 将接收天线安装在其他位置。 增大设备与接收器之间的距离 已省略所有不必要的包装。我们努力使包装 将设备连接到与接收器所连接电路不同的 易于分成三种材料:纸板(盒)、泡沫塑料 电路上的插座。 (缓冲物)和聚乙烯(袋、保护泡沫板)。 您的系统中包含可回收利用的材料(如果 由专业公司拆卸)。请遵守当地有关包装 材料、废电池和旧设备的处理规定。 咨询经销商或经验丰富的无线电/电视技术 人员以寻求帮助。 FCC 辐射暴露声明: 本设备符合针对不受控环境规定的 FCC 辐 法规遵循注意事项 射暴露限制。 此发射器不得与任何其他天线或发射器放置 本设备符合 FCC 规则第 15 部分的规定。 在同一地点或一起使用。 操作必须遵守以下两个条件: 加拿大: 1.
8 常见问题解答 蓝牙设备无法发现耳机。 • 耳机可能连接至之前配对的设备。关闭已 连接的设备,或将其移出连接范围。 蓝牙耳机无法打开。 • 设备配对。按照用户手册中的说明将耳 电池电量不足。给耳机充电。 机与蓝牙设备重新配对。(参见第 6 页 的“首次将耳机与蓝牙设备配对”)。 蓝牙耳机无法与蓝牙设备配对。 蓝牙功能未开启。打开耳机之前,打开蓝牙 设备并开启设备上的蓝牙功能。 配对无法进行。 • 将两个耳机放入充电盒。 • 确保已禁用之前连接的任何蓝牙设备的 蓝牙功能。 • 在蓝牙设备上,从蓝牙列表中删除 “Philips SHB2505”。 • 将耳机配对(参见第 6 页的“首次将耳 机与蓝牙设备配对”)。 如何重置配对。 从充电盒中取出两个耳机。在两个耳机上按 两次多功能键,直至 LED 指示灯闪烁白光, 等待约 10 秒。配对成功时,您将听到“已连 接”的声音提示。 配对可能已重置,或耳机之前已与其他 蓝牙耳机已连接至支持蓝牙立体声的手机, 但音乐只能通过手机扬声器播放。 请参考手机用户手册。选择通过耳机收听 音乐。 音质太差,可听到爆音。 • 蓝牙设备超出连接范
可以收听音乐,但无法通过蓝牙设备控制音乐 • 左右听筒断开,请先关闭两个听筒。 (例如播放/暂停/快进/快退)。 然后,将两个听筒放回充电盒,放置 确保蓝牙音频源支持 AVRCP(参见第 10 页 5 秒后,再取出。这样可以打开并连 的“技术数据”)。 接两个听筒。将耳机重新连接至蓝牙 设备。 耳机音量太低。 某些蓝牙设备无法通过调节音量与耳机音量同 • 耳机连接到多个蓝牙设备。关闭所有 步。在这种情况下,必须单独在蓝牙设备上将 已连接设备的蓝牙功能。关闭两个听 音量调节至合理的音量。 筒。将两个听筒放回充电盒,放置 5 秒后,再取出。将耳机重新连接至蓝 无法将耳机连接到另一台设备,该怎么办? 牙设备。注意,耳机一次只能连接到 • 确保之前配对的设备的蓝牙功能已关闭。 一个蓝牙设备。将耳机重新连接至蓝 • 对第二个设备重复配对操作(参见第 6 页 牙设备时,请确保其他任何之前配对/ 的“首次将耳机与蓝牙设备配对”)。 连接的设备的蓝牙功能均已关闭。 我只能从一个耳机里听到声音。 • 如果以上解决方案均不起作用,请将 • 如果您正在通话,声音来自左听筒
Este equipamento não tem direito à proteção contra interferência prejudicial e não pode causar interferência em sistemas devidamente autorizados. Este produto está homologado pela ANATEL, de acordo com os procedimentos regulamentados pela Resolução 242/2000, e atende aos requisitos técnicas aplicados. Para maiores informações, consulte a site da ANATEL: www.anatel.gov.br 飞利浦和飞利浦盾牌微标是 Koninklijke Philips N.V.