SHK4000 User Manual Register your product and get support www.philips.
1 Precautions Hearing Safety General Information English Table of Contents 2 2 2 2 Bluetooth Wireless Headphone 3 Box Contents Other Devices Bluetooth Wireless Headphone Overview 3 Getting Started Charging the Headphone Pairing Headphone with Your Phone 4 Using the Headphone Connecting Headphone to Bluetooth Device Call and Music Management Wearing the Headset 3 3 4 5 5 5 6 6 6 7 5 Technical Specification 8 6 Precaution 9 9 Declaration of Conformity Disposal of Old Products and Batteries EMF Co
1 Precautions Caution • • • • • Hearing Safety • • • Danger • To avoid hearing damage, reduce the time you use the headphone at high volume and set the volume to a safe level. The louder the volume, the shorter the safe listening time is. Be sure to observe the following guideline when using your headset. • Listen at the right volume for the right amount of time. • Do not keep the volume up just because your hearing adapts to a high volume.
Bluetooth Wireless Headphone Thank you for purchasing a Philips product! Register your product at www.philips.com/welcome to get support from Philips. With Philips wireless headphone, you may have • Convenient Wireless hands-free call • Wireless music listening and control • Switch between call and music English 2 Quick Start Guide Other Devices Compatible with mobile phones or devices (laptops, PDAs, Bluetooth adapters, MP3 players, etc.
Bluetooth Wireless Headphone Overview a Volume/Track control b • • Headset Power Play/Pause/Answer Call/Hang Up/Redial/Reject c Microphone d Charging slot 4 EN
1 Make sure the headphone is fully charged and powered off. 2 Press and hold the button for about six seconds until it flashes in blue and red by turns. The headphone remains in pairing mode for five minutes. Charging the Headphone Warning • • • Before using the headphone for the first time, charge the battery for about 4 hours for optimum battery capacity and life. Use only the genuine USB charging cable to avoid any damage.
4 Using the Headphone Connecting Headphone to Bluetooth device 1 2 Press and hold headset. Turn on the headphone. Action Press and hold for over one second. Useful Tip If you turn on the phone/Bluetooth device or activate the Bluetooth function after turning on the headphone, you must manually reconnect the headphone and the phone/Bluetooth device. Note If the headphone is not connected to a Bluetooth device within 5 minutes, it is automatically turned off to save battery.
Status LED Light The headphone The blue LED blinks is connected to a every 6 seconds. Bluetooth device while in standby mode or you're listening to music. The headphone is ready for pairing. The LED flashes in white and blue by turns. The headphone is on but not connected to a Bluetooth device. The blue LED blinks quickly. The battery power is low. The blue LED blinks twice every second. The battery is fully charged. The white LED is blinking. The battery is fully charged.
5 Technical Specification • • • Up to 9 hours for play or call Up to 200 hours for standby Normal time taken for full charge: 3 hours Rechargeable lithium-polymer battery (200mAh) Bluetooth 3.0, Bluetooth Mono support (Headset Profile - HSP, Hands-Free Profile - HFP), Bluetooth Stereo support (Advanced Audio Distribution Profile A2DP, Audio Video Remote Control Profile - AVRCP) Frequency range: 2.402 - 2.
English 6 Precaution Removing Built-in Battery Declaration of Conformity Gibson Innovations hereby declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. You may find the Declaration of Conformity at www.p4c.philips.com. Disposal of Old Products and Batteries Note • Before removing the battery, make sure the headset is disconnected from the USB charging cable.
This system consists of the materials which can be recycled if disassembled by a designated company. Check out the local regulations regarding disposal of the packaging materials, discharged batteries and older equipment. Trademarks Bluetooth Bluetooth word mark and logo are the trademarks of Bluetooth SIG, Inc., and trademarks such as Gibson Innovations are used under the corresponding licenses.
Questions (FAQs) The Bluetooth headphone is not turned on. The battery level is low. Charge your headphone. I can't pair my Bluetooth headphone with my phone. Bluetooth has been disabled. Activate the Bluetooth feature of the phone and turn on the phone before turning on the headphone. Pairing does not work. Make sure the headphone is in pairing mode. • Follow a step-by-step guide described in the user manual (see 'Pairing Headphone with Your Phone' on page 5).
2017 © Gibson Innovations Limited. All rights reserved. This product is manufactured and sold under authority of Gibson Innovations Ltd., which is the guarantor of this product. Philips and the Philips official mark of Koninklijke Philips N.V. are the registered trademark of Koninklijke Philips N.V. UM_SHK4 WK1 _00_EN_V1.
