Always there to help you Register your product and get support at www.philips.
EN
1 Your universal remote 2 2 2 3 2 Get started 4 4 5 Introduction Overview of the universal remote Supported devices Insert batteries (not included) Set up the universal remote 3 Notice 9 9 10 4 Service and support 11 11 11 Notice of compliance Disposal of your old product and batteries Frequently asked questions Need help? EN 1 Eng l i sh Contents
1 Your universal remote Congratulations on your purchase, and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/welcome Introduction With the universal remote, you can operate up to 4 different devices. Overview of the universal remote a b c d e f g a INPUT: select available source inputs (antenna, cable, etc.). : power on or off.
d / / / : scroll the menu up/down/left/right. OK: confirm your selection. MENU: menu on or off. BACK: go back one menu level or exit. e : mute LAST: return to the previous tuned channel. CH+/CH-: go to the next/previous channel. VOL: adjust the volume. Eng l i sh c LIVE: displays live TV programs. LIST: displays a list of recorded programs. INFO: displays on-screen channel information. STREAM: shortcut to the Netflix. GUIDE: displays the program guide.
2 Get started Insert batteries (not included) Warning •• Check the battery polarity when inserting in the battery compartment. Incorrect polarity may damage the product. Caution •• Risk of explosion! Keep batteries away from heat, sunshine or fire. Never discard batteries in fire. •• Risk of decreased battery life! Never mix different brands or types of batteries. Note •• When you replace the batteries, all user settings will be retained in the memory of the universal remote for 5 minutes.
You must first set up the universal remote before operating your devices. Manual registration 1 Switch on your device. 2 Press and hold the device selection button (e.g. TV) for 5 seconds until the blue LED is on. 3 Look up the 5-digit code for your brand in the code list. Codes are listed by the device type and brand name. The most popular code is listed first.
4 Enter the first 5-digit code using the digit buttons. 5 If the light is off, a valid code is saved. Otherwise, the light will flash once, and then remains on for code re-entry. 6 Operate the device with the universal remote. If your device responds correctly, it means you have entered the right code. Otherwise, repeat from step 2, and enter the second code on the list. Note •• It is possible sometimes that your device only responds to some of the buttons.
Eng l i sh Auto registration 1 Switch on your device. 2 Press and hold the device selection button (e.g. TV) for 5 seconds until the blue LED is on. 3 Point at your device with the universal remote. Then press and release to start searching the code for your brand. A different infrared signal is sent every 2 seconds as the universal remote searches, indicated by a blue flash.
4 When the device is off, immediately press and release OK to save the code. The blue LED indicator will turn off. max. 20 minutes 5 Operate the device with the universal remote. If your device responds correctly, it means you have saved the right code. Note •• Auto registration can be reversed, by pressing and releasing once more during the auto registration process. This is helpful if you missed out the chance to press OK within 2 seconds. Make sure that the device is first powered on again.
Eng l i sh 3 Notice Notice of compliance Notice for US This set complies with the FCC rules, Part 15 and with 21 CFR 1040.10. Operation is subject to the following two conditions: a This device may not cause harmful interference, and b This device must accept any interference received, including interference that may cause undesired operation. FCC rules This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
This Class B digital apparatus complies with Canadian ICES-003. IC Radiation Exposure Statement: This equipment complies with Canada radiation exposure limits set forth for uncontrolled environments. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Disposal of your old product and batteries Your product is designed and manufactured with high quality materials and components, which can be recycled and reused.
Eng l i sh 4 Service and support Frequently asked questions My universal remote does not work at all. •• Check if you have correctly setup the device with the right code. •• Check if you have pressed the corresponding device key for your device. •• Check if the batteries are inserted properly. If the battery level is low, replace the batteries. •• Check if your device is powered on.
2015 © Gibson Innovations Limited. All rights reserved. This product has been manufactured by, and is sold under the responsibility of Gibson Innovations Ltd., and Gibson Innovations Ltd. is the warrantor in relation to this product. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license from Koninklijke Philips N.V. UM_SRP3014_27_EN_V2.
