Universal Remote SRP5016 TAPR802 User manual Register your product and get support at www.philips.
Contents 1 Your universal remote Introduction 2 2 2 Get started 3 3 4 3 Use your universal remote control 6 6 Insert batteries (not included) Set up the universal remote Learning 4 Notice 7 Disposal of your old product and battery 7 5 Service and support Frequently asked questions Need help? 8 8 8 EN 1
1 Your universal remote Congratulations on your purchase, and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/welcome Introduction With the universal remote, you can operate up to 3 different devices. Overview of the universal remote 1 SAT BLU MEDIA 2 S.BAR 3 4 5 HOME SMART 6 a : power on or off. b Device selection buttons. c d : stop : pause : record : rewind : play : fast forward : previous track.
Supported devices 2 Get started Device name Description TV TV, DTV SAT Cable box, satellite receiver, IPTV, DVR, HDTV decoder and TiVo MEDIA Streaming devices, Apple TV, Roku, Sony, WD TV, Netgear BLU DVD player/recorder, Blu-ray player S.BAR Sound bar, home theater, audio system Insert batteries (not included) Warning •• Check the battery polarity when inserting in the battery compartment. Incorrect polarity may damage the product.
Set up the universal remote 12345 You must first set up the universal remote before operating your devices. 4 Set up by code selection 1 Switch on your device. Enter the first 5-digit code using the digit buttons. NFO 2 5 Press and hold the device selection button (e.g. TV) for 5 seconds until the red LED is on. If the light is off, a valid code is saved. Otherwise, the light will flash six times, and then remains on for code re-entry. SAT SAT BLU 3 4 MEDIA BLU S.BAR S.
seconds as the universal remote searches, indicated by a blue flash. Note •• It is possible sometimes that your device only responds to some of the buttons. In such case, set up with the next code in the code list, and try operating your device again. If there spill problem on code or key, you can try to learn a key by learning faction if the remote support learning function. •• Each device button can be used to set up any device. E.g. you may setup a TV using the SAT device button.
3 Use your universal remote control 7 Repeat from step 3 to learn other key functions, or press and hold any key for 3 secouds to terminate the learning mode, the LED indicator will go out immediately. Note •• On Step 4, if no key is selected for more than 15 Learning You must have an original remote for the Universal Remote Control (URC) to learn code from it. Learn commands 1 2 3 4 5 6 6 Press and hold the device selection button (e.g. TV) for 5 seconds until the red LED is on.
4 Notice Disposal of your old product and battery Your product is designed and manufactured with high quality materials and components, which can be recycled and reused. This symbol on a product means that the product is covered by European Directive 2012/19/EU. Removing the disposable batteries To remove the disposable batteries, see section ‘Insert batteries’.
5 Service and support Frequently asked questions My universal remote does not work at all. • Check if you have correctly setup the device with the right code. Check if you have pressed the corresponding device key for your device. • Check if the batteries are inserted properly. If the battery level is low, replace the batteries. • Check if your device is powered on.
Specifications are subject to change without notice. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license. This product has been manufactured by and is sold under the responsibility of MMD Hong Kong Holding Limited or one of its affiliates, and MMD Hong Kong Holding Limited is the warrantor in relation to this product. SRP5016_10_UM_V1.
