SW7700 © & ™ Lucasfilm Ltd.
1 9 2 3 10 4 5 6 11 7 8 12
empty page before TOC
English 6 简体中文 25
English Introduction Congratulations on your purchase and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/welcome. Please read this user manual, as it contains information about the features of this shaver as well as some tips to make shaving easier and more enjoyable. General description (Fig.
English 7 Danger - Keep the supply unit dry. Warning - To charge the battery, only use the detachable supply unit (HQ8505) provided with the appliance. - The supply unit contains a transformer. Do not cut off the supply unit to replace it with another plug, as this causes a hazardous situation.
English Caution - Never immerse the cleaning system or the charging stand in water and do not rinse it under the tap. - Never use water hotter than 60°C to rinse the shaver. - Only use this appliance for its intended purpose as shown in the user manual. - For hygienic reasons, the appliance should only be used by one person. - Never use compressed air, scouring pads, abrasive cleaning agents or aggressive liquids such as petrol or acetone to clean the appliance.
English 9 Electromagnetic fields (EMF) - This Philips appliance complies with all applicable standards and regulations regarding exposure to electromagnetic fields. General - This shaver is waterproof. It is suitable for use in the bath or shower and for cleaning under the tap. For safety reasons, the shaver can therefore only be used without cord. - The supply unit is suitable for mains voltages ranging from 100 to 240 volts.
English While the shaver continues to charge, first the bottom light of the battery status indicator flashes white and then lights up white continuously. Then the second light flashes and lights up continuously, and so on until the shaver is fully charged. Battery fully charged Note: This shaver can only be used without a cord. When the battery is fully charged, all lights of the the battery status indicator light up white continuously.
English 11 ’Unplug for use’ reminder The ‘unplug for use’ symbol flashes to remind you that you have to disconnect the shaver from the wall socket before you can switch it on. Cleaning reminder Clean the shaver after every shave for optimal performance (see 'Cleaning and maintenance'). When you switch off the shaver, the cleaning reminder flashes to remind you to clean the shaver. Travel lock You can lock the shaver when you are going to travel.
English Charging Charge the shaver before you use it for the first time and when the display indicates that the battery is almost empty. Charging takes approx. 1 hour. A fully charged shaver has a shaving time of up to 60 minutes. Note: You cannot use the shaver while it is charging. Charging with the supply unit 1 Make sure the shaver is switched off. 2 Put the small plug in the shaver and put the supply unit in the wall socket. The display of the shaver indicates that the shaver is charging.
English 13 Switching the shaver on and off 1 To switch the shaver on or off, press the on/off button once. The replacement symbol lights up continuously when the shaver is switched on. Shaving Skin adaptation period Your first shaves may not bring you the result you expect and your skin may even become slightly irritated. This is normal. Your skin and beard need time to adapt to any new shaving system.
English The display lights up for a few seconds to show the battery status. Wet shaving For a more comfortable shave, you can also use this shaver on a wet face with shaving foam or shaving gel. 1 Apply some water to your skin. 2 Apply shaving foam or shaving gel to your skin. 3 Rinse the shaving unit under the tap to ensure that the shaving unit glides smoothly over your skin. 4 Switch the shaver on.
English 15 7 Switch off the shaver and clean it after each use. Note: Make sure that you rinse all foam or shaving gel off the shaver. Using the click-on attachment Removing or attaching the click-on attachment 1 Make sure the shaver is switched off. 2 Pull the attachment straight off the shaver. Note: Do not twist the attachment while you pull it off the shaver. 3 Insert the lug of the attachment into the slot in the top of the shaver.
English 3 Hold the trimmer perpendicular to the skin and move it downwards while exerting gentle pressure. 4 Switch off and clean the trimmer after use. Travel lock You can lock the shaver when you are going to travel. The travel lock prevents the shaver from being switched on by accident. Activating the travel lock 1 Press the on/off button for 3 seconds to enter the travel lock mode. 3 sec. While you activate the travel lock, the indications on the display light up briefly.
English 17 Cleaning and maintenance - Regular cleaning guarantees better shaving results. - Never clean, remove or replace the shaving unit while the shaver is switched on. - Do not apply pressure to shaving head combs. - Do not touch shaving heads with hard objects as this may dent or damage the precision-made slotted combs. - Do not use abrasives, scourers or aggressive liquids such as gasoline or acetone to clean the shaver.
English 4 Rinse the hair chamber under the tap. 5 Rinse the shaving head holder under a warm tap. 6 Carefully shake off excess water and let the shaving head holder air dry completely. 7 Attach the shaving head holder to the bottom part of the shaving unit (‘click’). Cleaning the precision trimmer attachment Never dry the trimmer with a towel or tissue, as this may damage the trimming teeth. Clean the trimmer after each use. 1 Switch the shaver on. 2 Rinse the trimmer under a warm tap.
English 19 Replacement Replacing the shaving heads 2yrs For maximum shaving performance, we advise you to replace the shaving heads every two years. Replace damaged shaving heads immediately. Always replace the shaving heads with original Philips shaving heads. Replacement reminder The replacement reminder indicates that the shaving heads need to be replaced.The replacement reminder flashes when you switch the shaver off. 1 Switch the shaver off.
English 5 Place the new shaving heads in the shaving head holder. Note: Make sure the notches on both sides of the shaving heads fit exactly onto the projections in the shaving head holder. 1 2 6 Place the retaining ring on the shaving head and turn it clockwise to reattach the retaining ring. Repeat this process for the other retaining rings. - Each retaining ring has two recesses that fit exactly around the projections of the shaving head holder.
English 7 sec. 21 8 To reset the replacement reminder, press and hold the on/off button for approx. 7 seconds. Storage Store the shaver in the pouch. Note: Always let the shaver dry before you store it in the pouch. Ordering accessories To buy accessories or spare parts, visit www.shop.philips.com/service or go to your Philips dealer. You can also contact the Philips Consumer Care Center in your country (see the international warranty leaflet for contact details).
English - This product contains a built-in rechargeable battery which shall not be disposed of with normal household waste. We strongly advise you to take your product to an official collection point or a Philips service centre to have a professional remove the rechargeable battery. - Follow your country’s rules for the separate collection of electrical and electronic products and rechargeable batteries. Correct disposal helps prevent negative consequences for the environment and human health.
English 23 Warranty and support If you need information or support, please visit www.philips.com/support or read the international warranty leaflet. Warranty restrictions The shaving heads (cutters and guards) are not covered by the terms of the international warranty because they are subject to wear. Troubleshooting Shaver Problem Possible cause The appliance does not work when I press the on/off button.
English Problem Possible cause Solution Hairs or dirt obstruct Clean the shaving heads in the shaving heads. the regular way or clean them thoroughly. To clean the shaving heads thoroughly, remove the shaving heads from the shaving head holder one by one (see 'Replacement'). Then separate the cutter from its guard and rinse each matching set under the tap. After rinsing, place the cutter back into its corresponding guard.
简体中文 25 介绍 感谢您的惠顾,欢迎光临飞利浦! 为了让您能充分享 受飞利浦提供的支持,请在 www.philips.
简体中文 警告 - - - 要给电池充电,请仅使用产品随附的可拆卸电源部 件 (HQ8505)。 电源部件中包含一个变压器。 请勿自行更换电源部 件的插头,否则将导致严重后果。 本产品也可以由 8 岁或以上年龄的儿童以及肢体不 健全、感觉或精神上有障碍或缺乏相关经验和知识 的人士使用,但前提是有人对他们使用本产品进行 监督或指导,以确保他们安全使用,并且让他们明 白相关的危害。 切勿让儿童玩弄本产品。 不要让儿 童在无人监督的情况下对本产品进行清洁和保养。 将剃须刀手持部分与电源软线分开后,才能在水龙 头下清洗手持部分。 使用前,请务必检查产品。 请勿使用损坏的产品, 否则可能对人体造成伤害。 请务必用原装型号更换 损坏的部件。 切勿拆开本产品更换充电电池。 警告 - - 切勿将清洁系统或充电座浸入水中,也不要在水龙 头下冲洗。 警告符号注释: 禁止在打开的水龙头下进行清洗 切勿使用温度高于 60°C 的热水冲洗剃须刀。 只能将本产品用于用户手册中所示的原定用途。 出于卫生的目的,本产品只能供一个人使用。 切勿使用压缩气体、钢丝绒、研磨性清洁剂或腐蚀 性液体(例如汽油或丙酮)来清洁产品。
简体中文 - - 27 冲洗剃须刀时,水可能从产品底部的插口漏出。 这 是正常的,而且没有危险,因为所有电子元件都封 闭在剃须刀内部的密封电源部件中。 请勿在包含电动空气清新器的墙壁插座上或其周围 使用电源部件,以免电源部件受到不可修复的损 坏。 电磁场 (EMF) - 本 Philips 产品符合所有有关暴露于电磁场的适用标 准和法规。 - 符号注释:适合于在洗澡或淋浴时使用。 允许在盛 水的浴缸、淋浴、洗脸盆或其他器皿附近使用本器 具。 该剃须刀具有防水性能。 适合在沐浴或淋浴时使 用,也可以放在水龙头下清洗。 出于安全原因,该 剃须刀在使用时不能连接电线。 电源部件适合在 100 - 240 伏的电源电压下工作。 该电源部件可将 100-240 伏的电压转换为 24 伏以 下的安全低电压。 概述 - - 显示屏 启动顺序 当您第一次按下开/关按钮时,所有指示灯依次亮起。 使用前先为剃须刀充电。 充电 快速充电: 电池电量耗尽后,当您将剃须刀连接到电 源插座时,电池状态指示灯将逐个呈白色亮起并重复循 环。 当电池包含的电量足够完成一次剃须时,则底部 的电池状态指示灯会开始呈白色缓慢
简体中文 如果本剃须刀继续充电,底部的电池状态指示灯会先呈 白色闪烁,然后呈白色持续亮起。 然后,第二个指示 灯闪烁,之后持续亮起,以此类推,直至剃须刀充满 电。 电池已完全充满 注意: 本剃须刀只能在不接电源的情况下使用。 电池充满电后,所有电池状态指示灯都将呈白色持续亮 起。 注意: 如果在充电期间或之后按下开/关按钮,“拔出 插头即可使用”符号会亮起,表示剃须刀仍然与电源插 座相连。 注意: 电池充满电后,显示屏会在 30 分钟后自动关 闭。 电池电量不足 当电池电量几乎耗尽时,电池状态指示灯的底灯会呈橙 色闪烁。 电池剩余电量 剩余的电池电量由持续亮起的充电指示灯来表示。
简体中文 29 “拔出插头即可使用”提示 “拔出插头即可使用”符号闪烁,提醒您应先断开剃须 刀与电源插座的连接再打开本产品。 清洗提示 每次剃须后请清洁剃须刀,以获得出色性能 (请参见 '清洁和保养')。关闭剃须刀时,清洗提示符号闪烁,提 醒您需要清洁剃须刀。 旅行锁 您可以在携带剃须刀旅行之前将其锁住。 旅行锁可防 止剃须刀被意外 (请参见 '启用旅行锁')打开。 更换提示 要获得最佳的剃须效果,请每两年更换一次剃须刀头。 剃须刀配有更换提示符号,它会提醒您更换剃须刀头。 更换提示符号闪烁即表示您应更换剃须刀头 (请参见 '更换剃须刀头')。 注意: 更换剃须刀头后,您需要通过按开/关按钮 7 秒 来重置更换提醒。 充电 首次使用剃须刀之前,或当显示屏指示电池电量几乎耗 尽时,请先为剃须刀充电。
简体中文 充电约需 1 小时。 充满电的剃须刀最长剃须时间 可达 60 分钟。 注意: 切勿在充电时使用剃须刀。 使用电源部件充电 1 确保剃须刀已关闭。 2 将小插头插入剃须刀,然后将电源部件插入电源插 座。 剃须刀显示屏将显示剃须刀正在充电。 3 充电之后,从电源插座上拔下电源部件,并从剃须 刀上拔下小插头。 使用剃须刀 使用前务必要检查剃须刀和所有配件。 如果剃须刀或 任何配件损坏,请勿再使用,否则可能对人体造成伤 害。 请务必用原装型号更换损坏的部件。 此标志表示该剃须刀可在沐浴或淋浴时使用。 - 请按照本用户手册中所述的预期家用用途使用本剃 须刀。 - 出于卫生考虑,请勿共用剃须刀。 - 皮肤和毛发干燥时修剪更容易。 注意: 本剃须刀只能在不接电源的情况下使用。 打开或关闭剃须刀 1 要打开或关闭剃须刀,请按一下开/关按钮。
简体中文 31 打开剃须刀后,更换符号会持续亮起。 剃须 皮肤适应期 前几次剃须可能不会带给您预期效果,并且您的皮肤可 能会受到轻度刺激。 这是正常的。 您的皮肤和胡须需 要时间适应任何新的剃须系统。 为了让您的皮肤适应 这款新产品,我们建议您在 3 周时间内定期(至少每 周 3 次)仅使用本产品剃须。 如果您连续 3 天或更长时间没有剃须,为确保皮肤获 得最佳舒适感,请预先修剪胡须。 干剃 1 打开剃须刀。 2 让剃须刀头在您的皮肤上作直线和迂回运动,以刮 剃向不同方向生长的所有须发。 轻轻按压,以获取 舒适贴面的剃须感受。 注意: 不要用力按压剃须刀,这样做可能会导致皮 肤受刺激。 3 每次使用后,请关闭并清洗剃须刀。 显示屏将亮起几秒钟时间,以显示电池状态。 湿剃 要获得更舒适的剃须体验,您也可以先用剃须泡沫或剃 须啫喱对脸部进行湿润,然后再使用剃须刀。 1 用水润湿皮肤。
简体中文 2 在皮肤上涂抹剃须泡沫或剃须啫喱。 3 在水龙头下冲洗一下剃须刀头部件,确保剃须刀头 部件可以在您的皮肤上顺畅滑动。 4 打开剃须刀。 5 让剃须刀头在您的皮肤上作迂回运动,以刮剃向不 同方向生长的所有须发。 轻轻按压,以获取舒适贴 面的剃须感受。 注意: 不要用力按压剃须刀,这样做可能会导致皮 肤受刺激。 注意: 定期冲洗剃须刀头部件,确保其能够继续在 您的皮肤上顺畅滑动。 6 擦干面部。 7 每次使用后,请关闭并清洗剃须刀。 注意: 确保冲净剃须刀上的所有泡沫或剃须啫喱。 使用卡入式附件 拆卸或安装卡入式附件 1 确保剃须刀已关闭。 2 将附件竖直抽出剃须刀。 注意: 将附件从剃须刀上抽出时,不要旋转。
简体中文 33 3 将附件的凸缘插入本剃须刀顶部的槽内。 然后,按 下附件将其安装到本剃须刀上(可听到“咔哒”一 声)。 使用精确修剪器附件 您可以使用精确修剪器修剪胡须、鬓角和须髭。 1 将修剪器安装到剃须刀上(听到“咔哒”一声)。 2 打开剃须刀。 3 将修剪器垂直放在皮肤上,向下移动产品,同时轻 轻按压。 4 使用后,请关闭并清洁修剪器。 旅行锁 您可以在携带剃须刀旅行之前将其锁住。 旅行锁可防 止剃须刀被意外打开。 启用旅行锁 1 按住开/关按钮 3 秒钟以进入旅行锁模式。 3 sec.
简体中文 当您启用旅行锁时,显示屏上的指示灯会短暂亮 起。 旅行锁启用后,旅行锁符号将闪烁。 解除旅行锁 1 按开/关按钮 3 秒钟。 当您解除旅行锁时,显示屏上的指示灯会短暂亮 起。 旅行锁解除后,旅行锁符号将闪烁,然后熄 灭。 剃须刀打开后即可供再次使用。 注意: 当连接到电源插座时,剃须刀会自动解锁。 清洁和保养 - 为保证更好的剃须效果,请定期清洗剃须刀。 切勿在剃须刀开启时清洗、拆除或更换剃须刀头部 件。 请勿对剃须刀头梳齿施加压力。 请勿使用硬物触碰剃须刀头,以免挫伤或损坏制作 精密的带槽梳齿。 切勿使用研磨剂、硬毛刷或汽油或丙酮等腐蚀性液 体清洗本剃须刀。 在水龙头下冲洗剃须刀 每次剃须后请清洁剃须刀,以获得出色性能。 切记先检查水温是否太高,以防烫手。 不要用毛巾或纸巾擦拭剃须刀头部件,因为这样可能会 损坏剃须刀头。 冲洗剃须刀头部件时,水可能会从剃须刀底座中滴出。 这属于正常现象。 1 打开剃须刀。
简体中文 35 2 用温水冲洗剃须刀头部件。 3 关闭剃须刀。 将剃须刀头支架从剃须刀头部件的底 部抽离。 4 在水龙头下冲洗胡茬储藏室。 5 用温水冲洗剃须刀头支架。 6 小心地甩掉多余水分并彻底晾干剃须刀头支架。 7 将剃须刀头支架安装到剃须刀头部件的底部(可听 到“咔哒”一声)。 清洁精确修剪器附件 切勿用毛巾或纸巾擦干修剪器,否则可能会损坏修剪 齿。 每次使用后都应清洁修剪器。
简体中文 1 2 3 4 打开剃须刀。 在热水龙头下冲洗修剪器。 清洁完成后,关闭剃须刀。 小心地甩掉多余水分并彻底晾干附件。 提示: 为达到最佳效果,请定期用一滴缝纫机油润 滑附件齿部。 更换 更换剃须刀头 2yrs 为获得最佳剃须效果,建议每两年更换一次剃须刀头。 立即更换损坏的剃须刀头。 务必使用原装飞利浦剃须 刀头进行更换。 更换提示 更换提示符号表示需要更换剃须刀头。关闭剃须刀后, 更换提示符号会闪烁。 1 关闭剃须刀。 2 将剃须刀头支架从剃须刀头部件的底部抽离。 2 1 3 逆时针转动固定环,然后将它从剃须刀头中取出。 对其他固定环重复此过程。 将其存放在安全的地 方。
简体中文 37 4 从剃须刀头支架上卸下剃须刀头。 立即丢弃用过的剃须刀头,以免与新的剃须刀头混 淆。 5 将新的剃须刀头装到剃须刀头支架中。 注意: 确保剃须刀头两侧的槽口正好卡入剃须刀头 支架上的凸起部位。 1 2 6 将固定环放在剃须刀头上,顺时针旋转以重新安装 固定环。 对其他固定环重复此过程。 - 1 每个固定环均具有两个凹槽,正好与剃须刀头支架 的凸缘精准啮合。 顺时针旋转固定环,直至听 到“咔哒”一声,表明固定环已就位。 注意: 当您重新插入剃须刀头并重新安装固定环 时,请将剃须刀头支架握在手中。 切勿将剃须刀头 支架放在平面上,否则可能会损坏剃须刀头。
简体中文 7 将剃须刀头支架安装到剃须刀头部件的底部(可听 到“咔哒”一声)。 8 要重置更换提醒,请按住开/关按钮约 7 秒钟。 7 sec. 存放 将剃须刀存放在存储袋中。 注意: 务必始终将剃须刀晾干后,再存放到存储袋 中。 订购配件 要购买附件或备件,请访问 www.shop.philips.
简体中文 39 回收 - - - 弃置本产品时,请不要将其与一般生活垃圾放在一 起,应将其交给政府指定的回收中心。 这样做将有 利于环保。 此产品包含内置充电电池;请勿将充电电池与一般 生活垃圾一起弃置。 强烈建议您将自己的产品送到 官方收集点或飞利浦服务中心,让专业人士移除充 电电池。 遵循您的国家/地区有关分类回收电子电气产品和充 电电池的规定。 正确弃置产品有助于避免对环境和 人类健康造成不良后果。 卸下剃须刀的充电电池 仅在丢弃剃须刀时方可取出充电电池。 卸下电池 之前,请确保剃须刀与电源插座断开连接并且电 池电量已耗尽。 当您使用工具打开剃须刀时以及在您弃置充电电 池时,请采取必要的安全保护措施。 注意,电池带非常锋利。 1 将螺丝刀插入产品底部的前面板与后面板之间的插 槽。 拆除后面板。 2 卸下前面板。 3 拧下内侧面板顶部的两个螺丝,卸下内侧面板。 4 用螺丝刀取出充电电池。 ˌɫǩ؆ (Pb) мȞġĈҴˀΙĀǩ؆Ӎߒʔ ĈҴˀΙ ᰽ ⬡ ԣ͍Ჱ Ġ⅑ԓ᧠ Ġ⅑ȕ᧠⓭ (Hg) (Cd) (Cr (VI) ) (PBB) (PBDE) PCB’s X O O
简体中文 - 该表格中所显示的“有害物质”及其存在的部件向 消费者和回收处理从业者提供相关物质的存在信 息,有助于产品废弃时的妥善处理。 保修和支持 如需信息或支持,请访问 www.philips.com/support 或 阅读国际保修卡。 保修条款 由于剃须刀头(刀片和网罩)属于易磨损物品,因此不 在国际保修条款的涵盖范围之列。 保修与服务 This guarantee card is valid in China.
简体中文 41 网址:http://www.philips.com.
简体中文 For after-sales and maintenance service, please call service hotline 4008 800 008. Any comments and enquiries during the service, please Contact our Philips Consumer Lifestyle Customer Care Service Office. Philips(china)Investment Co.,Ltd. Philips Consumer Lifestyle Philips Innovation Campus Shanghai NO.1 Building, NO.10, Lane 888 Tian Lin Road Shanghai, P. R. C.
简体中文 问题 43 可能的原因 解决方法 旅行锁已被激活。 按住开/关按钮 3 秒钟以禁用 旅行锁。 剃须刀头部件被污染 或损坏,导致马达无 法运行。 彻底清洁剃须刀头或将其更 换。 有关如何彻底清洗剃须 刀头的详细说明,另请参 阅“毛发或污垢堵塞了剃须刀 头”。 产品的剃须效果没 剃须刀头已损坏或磨 有以前好。 损。 毛发或污垢堵塞了剃 须刀头。 更换剃须刀头。 对剃须刀头进行常规或彻底清 洁。 要彻底清洁剃须刀头,请将剃 须刀头从剃须刀头支架上逐一 (请参见 '更换')卸下。 然后, 分离刀片和网罩,并在水龙头 下冲洗每个刀片和网罩套装。 冲洗后,将刀片放回对应的网 罩中。 最后,将剃须刀头装 回到剃须刀头支架 (请参见 '更换')中。 我更换了剃须刀 您尚未重置更换提 头,但仍然显示更 示。 换提醒。 要重置更换提醒,请按住 开/关按钮约 7 秒钟。 水从产品底部漏 出。 这是正常现象,而且没有危 险,因为所有电子元件都封闭 在产品内部的密封电源部件 中。 在清洁过程中,水可 能聚集在产品的机身 内部与外壳之间。
简体中文 保留备用 发行日期: 28/7/2017
Empty page before back cover
© 2017 Koninklijke Philips N.V. All rights reserved 保留所有权利 4222.002.7380.