真無線藍牙 運動耳機 5000 系列 TAA5508 使用手冊 請於以下網址註冊您的產品並獲得支援: www.philips.
目錄 1 重要安全說明 2 2 您的藍牙耳機 3 3 入門指南 5 4 使用耳機 8 5 重設耳機 10 6 技術資料 10 7 通知 11 8 商標 13 9 常見問題 14 聽力安全 一般資訊 包裝盒內物品 其他裝置 無線藍牙耳機概述 為電池充電 配戴方式 應用程式下載 首次將耳機與藍牙裝置配對 將耳機與另一個藍牙裝置進行配對 將耳機連接到您的藍牙裝置 控制 ANC(主動降噪) 開機/關機 管理您的通話和音樂 語音助理 耳機 LED 指示燈狀態 充電盒 LED 指示燈狀態 符合性聲明 處置舊產品和電池 取出內建的電池 EMF 相容性 環境資訊 合規通知 2 2 3 3 4 5 6 6 6 7 8 8 8 9 9 9 9 11 11 11 11 12 12
1 重要安全說明 聽力安全 一般資訊 為避免損壞或故障: 注意事項 • 請勿將耳機置於過熱環境。 • 請勿摔落耳機。 • 請避免水滴潑濺耳機。(請參閱特定產品的 IP 等級) • 請勿將耳機浸入水中。 • 請勿在連接器或插座濕潤時為耳機充電。 • 請勿使用任何含有酒精、氨水、苯或研磨劑的 清潔劑。 危險 • 為避免聽力受損,請限制以高音量使用耳機的 時間,並將音量設定在安全水平。音量越高, 可安全收聽的時間就越短。 使用耳機時,請務必遵守以下準則: • 合理使用耳機收聽音樂。使用時間和音量 都應合理。 • 請注意,聽力逐漸適應後,請勿持續調高 音量。 • 請勿將音量調得太高,以免您聽不到周圍 的聲音。 • 在可能發生危險的情況下,您應格外小心 或暫時停止使用本產品。 • 耳機的聲壓過高會導致聽力喪失。 • 不建議在開車時雙耳使用耳機,這在某些 地方可能是非法的。 • 為了您的安全,請避免在交通途中或其他 可能發生危險的環境中因音樂或通話而 分心。 2 TW • 如需清潔,請使用柔軟的布料(必要時,可用少量 清水或經過稀釋的溫和肥皂潤濕布料)。 • 請勿將內建電池暴露在過熱的環境下
2 您的藍牙耳機 恭喜您購買本產品!歡迎您加入 Philips 的 使用者行列!若要充分利用 Philips 提供的 支援,請在 www.philips.
真無線藍牙運動耳機 1 2 3 4 5 a 多功能觸控 (MFT) b LED 指示燈(耳機) c 藍牙配對按鈕 d LED 指示燈 (電池狀態或充電狀態) e USB-C 充電插槽 4 TW
3 入門指南 為電池充電 耳機 將耳機放入充電盒。 • • 耳機開始充電,白色 LED 指示燈亮起 耳機充滿電後,白色指示燈熄滅 附註 • 首次使用耳機之前,請將耳機放入充電保護盒中 並為電池充電 2 小時,以達到最佳的電池容量和 使用壽命。 • 請務必使用原廠的 USB-C 充電纜線,以免造成 任何損壞。 • 對耳機充電之前,請先結束通話。連接耳機進行 充電將讓耳機關機。 • 如果長時間不使用耳機,可充電電池將開始損耗 其電荷。為避免這種損耗,請至少每三個月將 電池充滿電一次。 提示 • 通常,使用 USB 纜線充滿電需要 2 小時(對於 耳機或充電盒)。 充電盒 將 USB-C 纜線的一端插入充電盒,另一端 連接到電源。 提示 • 充電盒可當成攜帶式備用電池使用,並用於為 耳機充電。當充電盒充滿電後,它可以為耳機提供 3 次完整的充電。 TW 5
配戴方式 應用程式下載 選取合適的耳塞以獲得最佳貼合度 掃描 QR 碼/按「下載」按鈕或在 Apple App Store 或 Google Play 中搜尋「Philips Headphones」即可下載應用程式。 緊密、牢固的貼合將提供最佳的音質和 噪音消除。 1 2 測試哪個耳塞為您提供最佳的聲音和 佩戴舒適度。 提供 3 種尺寸的矽膠耳塞:大號、 中號、小號。 L M S Philips Headphones 應用程序讓您掌控 正在聆聽的音樂。您可以客製化聲音,讓 您的音樂和通話體驗始終最適合您的需求。 首次將耳機與藍牙裝置配對 插入耳機 1 2 1 2 區分左右耳機。 請確保耳機已充滿電且已關機。 打開充電盒的蓋子,耳機將處於配對 模式且可連接。 » 兩耳機上的 LED 指示燈都交替閃爍 白色和藍色 將耳機插入耳朵並輕輕扭動,直到牢固 貼合為止。 3 4 » 現在,耳機處於配對模式,可以與 藍牙裝置(例如,手機)配對。 開啟您藍牙裝置的藍牙功能。 將耳機與您的藍牙裝置進行配對, 請參閱您藍牙裝置的使用手冊。 附註 • 開機後,如果耳機找不到先前連接的任何藍牙
以下範例展示如何將您的耳機與藍牙裝置 配對。 1 2 開啟藍牙裝置的藍牙功能,選取 Philips TAA5508。 如果出現提示,請輸入耳機密碼 「0000」(4 個零)。針對具備藍牙 3.
4 使用耳機 控制 ANC(主動降噪) 啟用 ANC 將耳機連接到您的藍牙裝置 1 2 開啟您藍牙裝置的藍牙功能。 開啟充電盒的蓋子。 » 藍色 LED 指示燈閃爍。 透 過 按 兩 下 右 耳 機 可 以 切 換 不 同 的 ANC 模式。 • • • ANC 功能會在將耳機放入耳朵時自動 啟用 觸碰兩下 MFT 將關閉 ANC 功能 再觸碰兩下 MFT 將變為感知模式 » 耳機將搜尋最後連接的藍牙裝置, 並自動重新連接。如果最後連接的 裝置無法使用,耳機將搜尋並重新 連接到倒數第二個連接的裝置。 感知模式 ANC 開啟 提示 ANC 關閉 • 如果在開啟耳機後再開啟藍牙裝置的藍牙功能, 則必須先進入裝置的藍牙功能表,再以手動方式 將耳機連接到裝置。 附註 • 在某些藍牙裝置中,可能無法自動連接。在這種 情況下,您必須進入裝置的藍牙功能表,然後以 手動方式將耳機連接到藍牙裝置。 任務 MFT 操作 ANC 開啟 左耳機 按兩下 ANC 關閉 左耳機 按兩下 感知模式 左耳機 按兩下 快速感知 左耳機 嗶聲後繼續觸碰 MFT 操作 開機/關機 任務
管理您的通話和音樂 耳機 LED 指示燈狀態 音樂控制 耳機狀態 指示燈 耳機已連接到藍牙 裝置。 白色 LED 指示燈 閃爍一次 耳機已準備好進行 配對 藍色與白色 LED 指示燈交替閃爍 耳機已開機但未連接 到藍牙裝置 白色 LED 指示燈每秒 閃爍一次(3 分鐘後 自動關閉) 電池電量低(耳機) 白色 LED 指示燈 每 5 秒閃爍 3 次 電池已充滿電 (充電盒) 請參閱充電盒 LED 指示燈狀態 任務 MFT 操作 播放或暫停音樂 右耳機 按兩下 下一首曲目 右耳機 按三下 上一首曲目 左耳機 按三下 調整音量 + 右耳機 按一下然後按住 調整音量 - 左耳機 按一下然後按住 通話控制 任務 MFT 接聽/掛斷電話 右/左耳機 按一下 掛斷電話/拒接 來電 右/左耳機 按兩下 操作 語音助理 任務 按鈕 操作 觸發語音 (Siri/ Google) 助理 右耳機 嗶聲後繼續觸碰 停止語音助理 右耳機 按一下 充電盒 LED 指示燈狀態 充電時 指示燈 電池低電量 琥珀色 LED 指示燈 亮起 電池
5 重設耳機 6 技術資料 如果您遇到任何配對或連線問題,您可 按照以下程序將耳機重設為出廠預設設定。 • 1 在您的藍牙裝置上,進入藍牙選單並將 Philips TAA5508 從裝置清單移除。 2 關閉您藍牙裝置的藍牙功能。 3 將耳機放回充電盒並打開蓋子。 4 按兩次充電盒上的按鈕。 5 請依「使用耳機 — 將耳機連接到您的 藍牙裝置」中的步驟進行操作。 • • • • • • 6 將耳機與藍牙裝置配對,選取 Philips TAA5508。 如果耳機沒有回應,您可按照以下步驟 重設耳機的硬體。 • 將耳機放回充電盒並打開蓋子。按住 充電盒上的按鈕超過 10 秒。 • • • • • • • 音樂播放時間 (ANC 開啟):7 + 21 小時 音樂播放時間 (ANC 關閉):8 + 23 小時 待命時間:200 小時 充電時間:2 小時 電池:53 mAh 鋰離子電池 (各耳機),600 mAh 鋰離子電池 (充電盒) 藍牙版本:5.
7 通知 符合性聲明 MMD Hong Kong Holding Limited 特此 聲明,本產品符合 RED 指令 2014/53/EU 和 UK Radio Equipment Regulations SI 2017 No 1206 的基本要求和其他相關 規定。您可以在 www.philips.
環境資訊 所有非必要的包裝均已省略。我們已嘗試 使用三種材料製成的簡易包裝:紙板 (箱子)、聚苯乙烯泡棉(緩衝)和 聚乙烯(袋子,泡棉保護板)。 您的系統包含的材料可由專業公司拆解後 進行回收和再利用。請遵守當地有關包裝 材料、廢電池和舊有裝置棄置的規定。 FCC 輻射暴露聲明: 此裝置符合針對不受控制的環境制訂的 FCC 輻射暴露限值。 此發射器不得與任何其他天線或發射器 放在一起或一起使用。 注意事項:使用者須注意,未經合規 負責人明確批准的任何變更或修改,都有 可能讓使用者喪失操作此裝置的權限。 加拿大: 2.
8 商標 藍牙 Bluetooth® 文字標記和商標是 Bluetooth SIG, Inc. 的註冊商標, 且 MMD Hong Kong Holding Limited 對此類標記的任何使用均已獲得許可。 其他商標和商品名稱歸其各自擁有者所有。 Siri 「Siri」是 Apple Inc. 在美國和其他國家/ 地區的商標。 Google Google 和 Google Play 是 Google LLC.
9 常見問題 我的藍牙耳機無法開啟。 電池電量不足。請對耳機充電。 我無法將藍牙耳機與藍牙裝置配對。 藍牙功能已被停用。在開啟耳機之前, 請在藍牙裝置上啟用藍牙功能並開啟藍牙 裝置。 無法配對。 • 將兩個耳機都放入充電盒中。 • 請確認已經停用任何先前連接過的藍牙 裝置的藍牙功能。 • 在您的藍牙裝置上,將「Philips TAA5508」從藍牙清單中刪除。 • 配對您的耳機(請參閱第 6 頁上的 「首次將耳機與藍牙裝置配對」)。 藍牙裝置找不到耳機。 • 耳機可能已連接到先前配對的裝置。請 關閉連接的裝置或將其移出連接範圍。 • 配對可能已經重設,或者耳機先前已與 其他裝置配對。請依使用手冊所述, 再次將耳機與藍牙裝置配對。(請參閱 第 6 頁的「首次將耳機與藍牙裝置 配對」)。 14 TW 我的藍牙耳機已連接到支援藍牙立體聲的 手機,但是音樂只能透過手機喇叭播放。 請參閱手機的使用手冊。選擇透過耳機 收聽音樂。 音訊品質差,並可聽到爆裂聲響。 • 藍牙裝置超出範圍。請縮短耳機與藍牙 裝置之間的距離,或清除它們之間的 障礙物。 • 對耳機充電。 從手機串流時很緩慢,且音訊品質變差, 或音訊串流根本無
2023 © MMD Hong Kong Holding Limited。保留所有權利。 規格如有變更,恕不另行通知。Philips 和 Philips 盾牌標誌是 Koninklijke Philips N.V. 經授權使用的註冊商標。本產品由 MMD Hong Kong Holding Limited 或其關聯公司之一製造並負責 銷售。MMD Hong Kong Holding Limited 是本產品的擔保人。 所有其他公司與產品名稱可能是其各自相關的公司的商標。 UM_TAA5508_00_TW_V1.