耳機 5000 系列 TAH5205 使用者手冊 請註冊產品,並在以下網址取得支援 www.philips.
目錄 1 重要安全說明 2 聽力安全 2 一般資訊 2 2 您的藍牙耳罩式耳機 3 包裝盒內有哪些內容物 3 其他裝置 3 藍牙無線耳機概述 4 3 入門指南 5 給電池充電 5 將耳機與手機配對 5 4 使用耳機 6 將耳機連接到您的藍牙裝置 6 管理您的通話和音樂 6 5 技術資料 8 6 通知 9 符合性聲明 9 棄置舊有產品和電池 9 卸下內置電池 9 符合 EMF 9 環境資訊 10 合規通知 10 7 商標 11 8 常見問題 12 TW
1 重要安全說明 一般資訊 為避免損壞或故障: 注意事項 聽力安全 • 請勿將耳機與充電盒放置在高溫下。 • 請勿讓您的耳機與充電盒掉落。 • 耳機與充電盒不應暴露在雨滴與噴濺水中。 • 請勿讓耳機與充電盒浸入水中。 • 請勿使用任何含有酒精、氨水、苯或研磨劑的清潔 • 如需清潔,請使用柔軟的布料(必要時,可用少量 • 請勿將內建電池暴露在過熱的環境中(例如,陽光、 • 更換電池不當可能引發爆炸。請務必使用相同或等 劑。 清水或經過稀釋的溫和肥皂潤濕布料)。 危險 • 火等)。 為避免聽力受損,請限制耳機使用高音量的時間 並將音量設定在安全水平。音量越大,可收聽音 效的電池進行替換。 樂的時間就越短。 使用耳機時,請務必遵守以下準則。 關於操作和存放耳機的適當溫度和濕度 • • 合理使用耳機收聽音樂。使用時間和音 量都應合理。 • • 請勿將音量調得太高,以免您聽不到周 • 在可能發生危險的情況下,您應格外小 • 耳機的聲壓過高會導致聽力喪失。 • 不建議在開車時使用遮住雙耳的耳機, 圍的聲音。 心或暫時停止使用本產品。 並且這在
2 您的藍牙耳罩 式耳機 快速入門指南 恭喜您購買本產品!歡迎您加入飛利浦的 使用者行列!若要充分利用飛利浦提供的 支援,請在 www.philips.
藍牙無線耳機概述 (電源開啟/關閉/配對) LED 指示燈 音量 + 音樂/通話控制按鈕 音量 低音增強 USB Type C 充電插槽 3.
3 入門指南 將耳機與手機配對 在您首次使用手機專用的耳機之前,請先將 為電池充電 注意事項 • 首次使用耳機之前, 請將耳機放入充電保護盒中 並為電池充電 3 小時,以達到最佳的電池容量和 使用壽命。 • 務必使用原廠的 USB 充電電纜,以免造成任何 損壞。 • 對耳機充電前,請先完成通話,因為連接耳機進 行充電會使耳機電源關閉。 耳機與手機配對。成功配對耳機與手機之 後,耳機和手機之間將建立起唯一的加密連 結。耳機會將最後 8 部裝置儲存在記憶體 中。如果您嘗試配對超過 8 部裝置,最早的 配對裝置將被新的裝置取代。 請確保耳機已充滿電力並且關閉。 按住 6 秒,直到藍色和白色 LED 交 替閃爍為止。 耳機將維持在配對模式 5 分鐘。 請確保您已開啟手機並啟動其藍牙功能。 將隨附的 USB 充電電纜連接至: • 耳機上的 Type - C USB 充電插槽, 以及; • 充電器/電腦的 USB 連接埠。 充電期間,LED 指示燈會變成白燈, 將耳機與手機配對。有關詳細資訊,請 參閱手機的使用者手冊。 以下範例顯示如何將耳機與手機配對。 啟動手機的藍牙功能,選擇 Philips TA
4 使用耳機 管理您的通話和音樂 開機/關機 將耳機連接到您的藍牙裝置 任務 按鈕 操作 開啟耳機。 開機/關機 開啟手機/藍牙裝置。 按住 2 秒。 關閉耳機。 按住開機/關機按鈕 2 秒鐘以以開啟 開機/關機 耳機。 按住 4 秒。 白色 LED 亮起後 熄滅。 白色 LED 將亮起。 耳機會自動重新連接到最後連接 的手機/藍牙裝置。 提示 • 如果您在開啟耳機後開啟手機/藍牙裝置或啟動 藍牙功能,則必須手動重新連接耳機和手機/藍 牙裝置。 注意事項 • 如果耳機在5分鐘內未能連接到上次連接的藍牙 裝置,它將改為配對模式。如果5分鐘後仍未連 接到任何藍牙裝置,耳機將自動關閉。 • 如果耳機沒有任何連接歷史,且在 5 分鐘內未連 接任何藍牙裝置的話,它將自動關機。 TW 音樂控制 操作 任務 按鈕 播放或暫停 音樂。 音樂/通話 按一次。 控制 調整音量。 按下以 +/- 下一首。 按住 + 2 秒 上一首。 按住 - 2 秒
通話控制 語音助理 任務 按鈕 操作 任務 按鈕 操作 接聽/掛斷 電話。 音樂/通話 控制 按一次。 喚醒預設 語音助理 音樂/通話 控制 按兩次 在通話中切 換來電者。 音樂/通話 控制 按兩次。 拒接電話 音樂/通話 控制 按住 2 秒 保留目前 通話並接受 來電 音樂/通話 控制 按一次 保留目前 通話並拒絕 來電 音樂/通話 控制 按住 2 秒 拒絕目前 通話並接受 來電 音樂/通話 控制 按兩次 在通話之間 切換 音樂/通話 控制 按3次 其他耳機指示燈狀態 耳機狀態 指示燈 原本處於待機模式 的耳機已連接至藍 牙裝置,並可開始 收聽音樂。 藍色 LED 將每 4 秒 閃爍一次 耳機已準備好進行 配對。 藍色與白色 LED 交替閃爍。 耳機已開啟但未連 接到藍牙裝置。 藍色 LED 緩慢閃 爍。如果無法建立 連接,耳機將在 5 分鐘內自行關機。 電池電量低。 白色 LED 閃爍, 直到沒電為止 電池已充滿電力。 白色 LED 燈號 熄滅。 TW
5 技術資料 耳機 • 音樂播放時間:29 小時 ( 停用低音增 強功能) • 通話時間:21 小時 • 待機時間:166 小時 • 充電時間:2 小時 • 可充電鋰電池(250 mAh) • 藍牙版本:5.0 • 相容性的藍牙設定檔: • HFP(免持通話) • A2DP(進階音訊傳輸設定檔) • AVRCP(遠端視訊控制設定檔) • 可支援的音頻編碼器/解碼器:SBC • 頻率範圍:2.402-2.
6 通知 符合性聲明 取出內建的電池 MMD 香港控股有限公司特此聲明,本產品 如果您所在的國家/地區沒有設立一套電子產 符合 2014/53/EU 指令的基本要求和其他相 品的收集/回收系統,您可以在棄置耳機之前 關規定。您可以在 www.p4c.philips.
環境資訊 所有非必要的包裝均已加以省略。我們已嘗 試使用三種材料製成的簡易包裝:紙板(箱 子)、聚苯乙烯泡棉(緩衝)和聚乙烯(袋 • 重新調整或擺放接收天線。 • 增加裝置和接收器之間的距離 • 將設備連接到與接收器不同迴路的插座上。 • 諮詢經銷商或有經驗的無線電/電視技術人員 以尋求協助。 子,泡棉保護板)。 FCC 輻射暴露聲明: 您的系統包含的材料可由專業公司拆解後進 此設備符合針對不受控制的環境制訂的 FCC 輻 行回收和再利用。請遵守當地有關包裝材 射暴露限值。 料、廢電池和舊有設備棄置的規定。 此發射器不得與任何其他天線或發射器放在一 起或一起使用。 注意事項: 使用者須注意,未經合規負責人明 合規通知 確批准的任何變更或修改,都有可能讓使用者 本裝置符合 FCC 規則第 15 部分。操作須 加拿大: 符合以下兩個條件: 本裝置符合加拿大創新、科學及經濟發展部 1. 本裝置可能不會造成有害干擾,並且 (Innovation, Science and Economic 2.
7 商標 藍牙 Bluetooth® 文字標記和商標是 Bluetooth SIG, Inc.
8 常見問題 藍牙裝置找不到耳機。 • 耳機可能已連接到先前配對的裝置。關閉 連接的裝置或將其移出連接範圍。 • 配對可能已經重設,或者耳機先前已與其 他裝置配對。如使用說明書所述,再次將 耳機與藍牙裝置配對。(請參閱第 6 頁 我的藍牙耳機無法開啟。 「首次配對耳機與藍牙裝置」)。 請電池電量不足。為耳機充電。 我的藍牙耳機已連接到支援藍牙耳機的手機, 我無法將藍牙耳機與藍牙裝置配對。 但是音樂只能透過手機喇叭播放。 藍牙功能已被停用。在開啟耳機之前,請在藍 請參閱手機的使用者手冊。選擇透過耳機收聽 牙裝置上啟用藍牙功能並開啟藍牙裝置。 音樂。 如何重新設定配對。 音訊品質差,並可聽到爆裂聲響。 讓耳機保持在配對模式(紅色和藍色指示燈交 替閃爍),將電源按鈕 • 向上推至+並按住 6 秒鐘以上,直到紫色 LED 指示燈亮起為止。 藍牙裝置超出範圍。縮短耳機與藍牙裝置 之間的距離,或消除它們之間的障礙物。 • 為耳機充電。 我聽到音樂了,但無法透過藍牙裝置控制音樂 (例如,播放/暫停/向前一首/向後一首)。 請確認藍牙音訊來源可支援 AVRCP(請參閱 「技術資料」
Este equipamento não tem direito à proteção contra interferência prejudicial e não pode causar interferência em sistemas devidamente autorizados. Este produto está homologado pela ANATEL, de acordo com os procedimentos regulamentados pela 飛利浦和飛利浦盾牌標誌是 Koninklijke Philips NV 經授權使用的註冊商標。本產 品由 MMD Hong Kong Holding Limited 或其關聯公司之一製造並負責銷售。 MMD Hong Kong Holding Limited 是本產品的擔保人。 UM_TAH5205_00_TW_V1.