Headphones 7000 Series TAN7506 User manual Register your product and get support at www.philips.
Contents 1 Important safety instructions 2 Hearing Safety General information 2 2 2 Your Bluetooth wireless headphones 3 What's in the box Other devices Overview of your Bluetooth wireless headphones 3 3 4 3 Get started 5 Charge the battery Pair the headphones with your mobile phone 5 5 4 Use your headphones 6 Connect the headphones to your Bluetooth device Connect the headphone with your computer Manage your calls and music ANC (active noise cancelation) Voice Assistant Busy mode Philips Hea
1 Important safety instructions Hearing Safety Danger To avoid hearing damage, limit the time you use headphones at high volume and set the volume to a safe level. The louder the volume, the shorter the safe listening time is. Be sure to observe the following guidelines when using your headphones. • Listen at reasonable volumes for reasonable periods of time. • Be careful not to adjust the volume continuously upwards as your hearing adapts.
2 Your Bluetooth wireless headphones Congratulations on your purchase, and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/support. With this Philips wireless headphones, you can: • enjoy convenient wireless handsfree calls; • enjoy and control wireless music; • switch between calls and music.
Overview of your Bluetooth wireless headphones 4 5 8 6 7 R 9 R 10 1 2 3 4 5 6 7 8 9 10 LED indicator ANC On/Off/Ambient sound button Volume Microphone On/Off button Microphone (Power On / Off / Pairing) Volume + Voice Assistant touch panel USB-C charging slot Quick awareness touch panel
3 Get started Charge the battery Note Before you use your headphone for the first time, place charge the battery for 2 hours for optimum battery capacity and lifetime. Use only the original USB-C charging cable to avoid any damage. Finish your call before charging the headphone, as connecting the headphone for charging will power the headphone off. Connect the supplied USB-C charging cable to: • • The USB-C charging slot on the headphones and; The charger/USB port of a computer.
4 Use your headphones Connect the headphone to your Bluetooth device Turn on your mobile phone/ Bluetooth device. Press and hold the on/off button to turn the headphones on. The blue LED is on 3s. The headphones are reconnected to the last connected mobile phone/ Bluetooth device automatically. Tip If you turn on the mobile phone/Bluetooth device or activate the Bluetooth feature after turning on the headphones, you have to reconnect the headphones and mobile phone/Bluetooth device manually.
Music control Task Play or pause music Voice Assistant Button Operation Press once Press once Long press 1s Adjust volume Next track Previous track Task Trigger voice assistant Button Voice assistant Operation Touch and hold Long press 1s Busy mode Call control Task Button Operation Pick up Press once Hang up a call Press twice Switch caller during a call Press once Task Busy mode on/off Button Volume + and Volume - Operation Press both simultaneously for 3s to turn the Red LEDs on/off T
Other headphones indicator status Headphones status The headphones are connected to a Bluetooth device, while the headphones in standby mode or while you are listening to music. The headphones are ready for pairing. The headphones are on but not connected to a Bluetooth device. Low battery level. Battery is fully charged. Indicator The blue LED will flash once every 5s. The LED flashes blue and white alternately.
6 Notice Declaration of conformity Remove the integrated battery Hereby, MMD Hong Kong Holding Limited declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. You can find the Declaration of Conformity on www.p4c.philips.com. If there is no collection/recycling system for electronic products in your country, you can protect the environment by removing and recycling the battery before disposing the headphones.
Environmental information All unnecessary packaging has been omitted. We have tried to make the packaging easy to separate into three materials: cardboard (box), polystyrene foam (buffer) and polyethylene (bags, protective foam sheet.) Your system consists of materials which can be recycled and reused if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packaging materials, exhausted batteries and old equipment.
7 Trademarks Bluetooth The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by MMD Hong Kong Holding Limited is under license. Other trademarks and trade names are those of their respective owners. Siri Siri is a trademark of Apple Inc., registered in the U.S. and other countries. Google Google and the Google Logo are registered trademarks of Google Inc.
8 Frequently asked questions My Bluetooth headphone does not turn on. The battery level is low. Charge the headphone. I cannot pair my Bluetooth headphone with my Bluetooth device. The Bluetooth is disabled. Enable the Bluetooth feature on your Bluetooth device and turn on the Bluetooth device before you turn on the headphone. The Bluetooth device cannot find the headphone. • The headphone may be connected to a previously paired device. Turn off the connected device or move it out of range.
Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license. This product has been manufactured by and is sold under the responsibility of MMD Hong Kong Holding Limited or one of its affiliates, and MMD Hong Kong Holding Limited is the warrantor in relation to this product. UM_TAN7506_00_EN_V1.
