ヘッドホン 1000 シリーズ TAT1207 取扱説明書 製品登録とサポートのサイト www.philips.
目次 1 安全上のご注意 聴覚への影響 一般注意事項 2 2 2 2 True ワイヤレスイヤホンにつ いて 3 3 使用準備 5 同梱品 その他のデバイス True ワイヤレスイヤピースの概要 バッテリーを充電してくだ さい 着用方法 初めてイヤピースと Bluetooth デバイスをペアリングする場合 別の Bluetooth デバイスとイヤピ ースをペアリングする 4 イヤピースの使用法 Bluetooth デバイスにイヤピースを 接続する 電源オン/オフ 音楽と通話の管理 (ステレオモード) 音楽と通話の管理 (モノラルモード) 音声アシスタント イヤピース LED インジケーターの状態 充電ケース LED インジケーターの状態 3 3 4 5 5 6 7 8 8 8 8 9 9 9 9 5 イヤピースのリセット 10 6 技術データ 10 7 注意 11 適合宣言 使用済み製品とバッテリーの廃棄 内蔵バッテリーの取り外し EMF 規格準拠 環境に関する情報 準拠に関する注意 11 11 11 12 12 12 8 商標 14 9 よく尋ねられる質問 1
1 安全上のご注意 一般注意事項 損傷や不具合を避けるために: 注意 聴覚への影響 • ヘッドホンを高温に晒さないでください。 • ヘッドホンを落とさないでください。 • ヘッドホンに水滴や水がかからないようにしてくださ い。(お使いの製品の IP 等級を確認してください) • ヘッドホンを水の中に入れないでください。 • コネクターやソケットが濡れている場合にはヘッド ホンを充電しないでください。 • アルコール、アンモニア、ベンゼン、研磨剤を含む洗浄 剤は使用しないでください。 危険 • 耳を守るため、大音量でヘッドホンを長時間続けて • 清掃が必要な場合は、柔らかい布で拭いてください。 聞くことを避け、音量を上げすぎないようにご注意く ださい。音量が大きすぎると、安全に聞ける時間が 短くなります。 • イヤピースを使用するときは、次のガイドラインに 従ってください。 • 適切な音量で、適切な時間だけ聴取してく ださい。 • 耳が慣れてきますので、音量を上げ続けない ように注意してください。 • 周囲の音が聞こえないほど音量を大きくし ないでください。 • 危険を伴う場合には、使用を慎
2 True ワイヤレス イヤホンにつ いて ご購入頂きありがとうございます。 Philips へ ようこそ!Philips が提供するサポートをす べてご利用いただくには、 お客様の製品を www.philips.
True ワイヤレスイヤピースの 概要 1 2 3 4 1 LED インジケーター (イヤピース) 2 マルチファンクションボタン 3 USB-C 充電スロット 4 LED インジケーター (バッテリー残量 表示) 4 JA
3 使用準備 充電ケース USB-C ケーブルの一方の端を充電ケースに差 し込み、 もう一方の端を電源に差し込みます。 バッテリーを充電してくだ さい 注意 • ご使用の前に、バッテリーの容量と寿命を最適化す • • るため、充電ケースの上にイヤホンを置き、2時間充 電してください。 破損を防ぐため、付属の USB-C 充電ケーブルのみを 使用してください。 充電の前に通話を終了してください。 イヤピースを充 電しようとして接続すると、電源が切れます。 ヒント • 充電ケースは、イヤピース充電用のポータブルバック アップバッテリーとして使用できます。充電ケースを満 充電にすると、 イヤピースを2回充電できます。 イヤピース 着用方法 イヤピースを取り出し、絶縁ラベルを剥がし ます。 最適にフィットするイヤチップを選択します。 充電ケースにイヤピースを戻し、蓋を閉めます。 • イヤピースの充電が始まり、青い LED ライ トが点灯します • 満充電になると青いライトが消えます 確実にフィットすると、最高の音質やノイズア イソレーション能力が得られます。 1 音質が最高で快適に装着でき
イヤピースを挿入する 1 イヤピースの左右方向を確認します。 2 耳の中にイヤピースを入れ、確実に装着さ れるまでわずかにひねります。 注意 • 電源をオンにした後で、イヤピースが、以前に接続し た Bluetooth デバイスを見つけることができない場 合、 自動的にペアリングモードに移行します。 次の例では、 お使いの Bluetooth デバイスと イヤピースのペアリングの方法について説明 します。 1 お使いの Bluetooth デバイスの Bluetooth 機能をオンにし、 Philips TAT1207 を選択します。 初めてイヤピースと Bluetooth デバイスをペア リングする場合 2 指示されたら、イヤピースのパスワード 「0000」(ゼロ4つ) を入力します。 Bluetooth 3.
別の Bluetooth デバイスとイ ヤピースをペアリングする 別の Bluetooth デバイスとイヤピースをペア リングしたい場合、単にペアリングモードにし (左右両方のイヤピースのマルチファンク ションボタンを5秒間長押しする)、通常のペア リングと同様に、 2台目のデバイスを見つけ ます。 注意 • イヤピースのメモリには4台のデバイスが保存されま す。5台以上のデバイスをペアリングしたいデバイス場 合、新しいデバイスの代わりに一番最初のデバイスが 消去されます。 JA 7
4 イヤピースの 使用法 Bluetooth デバイスにイヤピ ースを接続する 1 お使いの Bluetooth デバイスの Bluetooth 機能をオンにします。 電源オン/オフ タスク マルチファン 操作 クションボ タン イヤピースの 電源を入れる 充電ケースから イヤピースを取 り出し電源を入 れる イヤピースの 電源を切る 充電ケースにイ ヤピースを戻して 電源を切る 2 充電ケースのカバーを開きます。 » 青い LED が点滅します » イヤピースは、一番最後に接続した Bluetooth デバイスを検索し、 自動的 に再接続します。 音楽と通話の管理 (ステレオモード) 音楽の制御 タスク ヒント • イヤピースの電源を入れた後で Bluetooth デバイ デバイスの スの Bluetooth 機能をオンにする場合、 Bluetooth メニューに移動し、手動でデバイスにイヤ ピースを接続する必要があります。 マルチファン 操作 クションボ タン 音楽の再生ま 左/右の たは一時停止 イヤピース 短く1回押す 次のトラック 短く2回押す 左/右の イヤピース
音楽と通話の管理 (モノラルモード) イヤピース LED インジケーターの状態 音楽の制御 イヤピースの状態 インジケーター イヤピースが Bluetooth デバイスに 接続されている 白い LED が5秒間点 滅する LED が青と白で交互 に点滅する タスク マルチファン 操作 クションボ タン 音楽の再生ま 左/右の たは一時停止 イヤピース 短く1回押す イヤピースのペアリン グ準備完了 次のトラック 短く2回押す イヤピースがオンだが 青い LED が1秒おき Bluetooth デバイスに に点滅する (3分後に 接続されていない 自動的に消灯) 左/右の イヤピース 音量調整+/- スマートフォンの コントロール 経由 通話の制御 タスク マルチファン 操作 クションボ タン 電話に出る/電 左/右の 話を切る イヤピース 短く1回押す 着信拒否 2秒間長押しする 左/右の イヤピース 音声アシスタント タスク ボタン 操作 音声アシス タント (Siri/ Google) の 起動 左イヤピ ース 2秒間長押しする 音声アシスタン
5 イヤピースのリセ ット ペアリングまたは接続で問題が発生した場 合、次の手順を実行して、 イヤピースを工場初 期状態に復帰させることができます。 6 技術データ • • • • • 1 お使いの Bluetooth デバイスで Bluetooth メニューに移動し、 デバイスリス トから Philips TAT1207 を削除します。 2 お使いの Bluetooth デバイスの Bluetooth 機能をオフにします。 3 イヤピースを充電ケースに戻し、蓋を閉じ、 もう一度蓋を開きます。 4 充電ケースからイヤピースを取り出します。 5 左右両方のイヤピースのマルチファンクシ • • • • • • 音楽再生時間:6 + 12時間 通話時間:6時間 充電時間:2時間 Bluetooth のバージョン:5.
7 注意 内蔵バッテリーの取り外し 適合宣言 お住まいの国に電子機器の回収/リサイクル規 則が規定されていない場合でも、 イヤピースを廃 棄する前に、 バッテリーを取り外してリサイクルす ることで、環境が保護できます。 MMD Hong Kong Holding Limited では、本 製品が 2014/53/EUの主要要件およびその他 の関連規定に準拠していることをここに宣言い たします。適合宣言は www.p4c.philips.
EMF 規格準拠 本製品は、電磁場への曝露に関するすべての該 当規則・規則に準拠しています。 環境に関する情報 不要な梱包材は使用されていません。当社では、 本製品の梱包材が、紙 (箱)、 ポリスチレンフォー ム (緩衝材)、 ポリエチレン (袋、保護用フォームシ ート) の3つの材質に簡単に分離できるよう努め ています。 本システムは、専門業者が分解した場合にリサイ クルと再使用が行なえる材料で構成されていま す。梱包材、使用済みバッテリー、古い機器の廃 棄に関する地元の規則に従ってください。 準拠に関する注意 本装置は、連邦通信委員会規則第15条に準拠 しています。本装置は、以下の2条件を理解した 上で操作してください: 1. 本装置が有害な妨害を発生させないこと。 2.
Lʼémetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR dʼInnovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence.Lʼexploitation est autorisée aux deux conditions suivantes : (1) Lʼappareil ne doit pas produire de brouillage; (2) Lʼappareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible dʼen compromettre le fonctionnement.
8 商標 Bluetooth Bluetooth® のワードマークとロゴは Bluetooth SIG, Incの登録商標です。 MMD Hong Kong Holding Limited ではそのライ センスに基づいてこうしたマークを使用してい ます。 その他の商標および商標名は、各権利 保有者の所有物です。 Siri Siri は、米国および諸外国で登録済の Apple Inc.
9 よく尋ねられる 質問 Bluetooth イヤピースの電源が入りません。 バッテリー残量が低下しています。 イヤピース を充電してください。 Bluetooth イヤピースと Bluetooth デバイス がペアリングできません。 Bluetooth が無効になっています。 イヤピース の電源を入れる前に、 お使いの Bluetooth デバイスで Bluetooth 機能を有効にし、 Bluetooth デバイスを起動してください。 ペアリングが動作しません。 • 両方のイヤピースを充電ケースに入れてく ださい。 • 以前に接続した Bluetooth デバイスの Bluetooth 機能が無効になっていること を確認します。 • お使いの Bluetooth デバイスの Bluetooth リストから 「Philips TAT1207」 を削除します。 • ヘッドセットをペアリングします (6 ペ ージの 「初めてイヤピースと Bluetooth デ バイスをペアリングする場合」 を参照して ください)。 Bluetooth イヤピースがステレオ対応の Bluetooth スマートフォンに接続されて
2021 © MMD Hong Kong Holding Limited。全著作権所有。仕様 は予告なく変更されることがあります。 PhilipsおよびPhilips Shield Emblemは、Koninklijke Philips N.V.の 登録商標であり、 ライセンスに基づいて使用されます。本製品は、 MMD Hong Kong Holding Limitedまたはその関連会社の責任の下に製造 および販売されており、 MMD Hong Kong Holding Limitedが本製品 に関する保証を担当します。 その他の会社名および製品名は、 それぞれ の関連会社の商標である可能性があります。 モデル:TAT1207JH、 TAT1207LC UM_TAT1207_00_JA_V1.