Headphones 1000 Series TAT1209 User manual Register your product and get support at www.philips.
Contents 1 Important safety instructions 2 2 Your True wireless earpieces 4 Hearing safety General information 2 2 What's in the box Other devices Overview of your True wireless earpieces 4 4 5 3 Get started 6 4 Use your earpieces 9 5 Reset the earpieces 11 6 Technical data 11 7 Notice 12 Charge the battery How to wear Pair for the �rst time Pair with another Bluetooth device 6 7 7 8 Connect to your Bluetooth device 9 Power on/off 9 Manage your calls and music 9 Voice Assistant 10 Earpiec
1 Important safety instructions Hearing safety Danger To avoid hearing damage, limit the time you use headphones at high volume and set the volume to a safe level. The louder the volume, the shorter the safe listening time is. Be sure to observe the following guidelines when using your headphones. • Listen at reasonable volumes for reasonable periods of time. • Be careful not to adjust the volume continuously upwards as your hearing adapts.
To avoid risk of �re, the equipment is supplied only by external power source which output shall comply with PS1 (with output capacity less than 15W). Operating and storage temperatures and humidity • Store in a place where the temperature is between -20°C (-4°F) and 50°C (122 °F) with up to 90% relative humidity. • Operate in a place where the temperature is between 0°C (32°F) and 45°C (113 °F) with up to 90% relative humidity. • Battery life may be shorter in high or low temperature conditions.
2 Your True wireless earpieces Congratulations on your purchase, and welcome to Philips! To fully bene�t from the support that Philips offers, register your product at www.philips.com/support. With these Philips True wireless earpieces you can: • Enjoy convenient wireless handsfree calls • Enjoy and control music wirelessly • Switch between calls and music Quick start guide Warranty Safety lea�et What's in the box Other devices A mobile phone or device (e.g.
Overview of your True wireless earpieces 1 2 3 4 5 1 LED indicator (earpieces) 2 Multi-function touch (MFT) 3 Bluetooth pair button 4 LED indicator (battery state or charging state) 5 USB-C charging slot 5 EN
3 Get started Charge the battery Note Earpieces Place the earpieces in the charging box. • • The earpieces start charging and the white LED light goes on When the earpieces are fully charged, the white light will go off Before you use your headphones, place them in the charging box and charge the battery for 2 hours for optimum battery capacity and lifetime. Use only the original USB-C charging cable to avoid any damage. Finish your call before charging.
How to wear Select suitable ear tips for optimum �t A tight, secure �t will provide the best sound quality and noise-cancellation. 1 2 Test which ear tips provide you with the best sound and wearing comfort. Pair the earpieces with your Bluetooth device for the �rst time 1 Make sure that the earpieces are fully charged and powered off. 2 3 sizes of silicone ear tips are provided : large, medium, small.
2 Enter the earpieces' password “0000” (4 zeros) if prompted. For those devices featuring Bluetooth 3.0 or higher, there is no need to enter a password. Philips TAT1209 Pair the earpieces with another Bluetooth device If you want to pair another Bluetooth device with the earpieces, just put them into pairing mode, (press button on box for 3 seconds with both earpieces inside and the cover open), then discover the second device as per normal pairing.
4 Use your earpieces Connect the earpieces to your Bluetooth device 1 2 Turn on the Bluetooth function of your Bluetooth device. Power on/off Task MFT Operation Turn the earpieces on Open the charging box to power on Turn the earpieces off Close the charging box to power off Open the charging box cover. The blue LED �ashes. The earpieces will search the last connected Bluetooth device and reconnect to it automatically.
Call control Operation Task MFT Pick up/ Hang up call Right/Left Single tap earpiece Hang up call/ Reject call Right/Left Double tap earpiece Voice Assistant Task MFT Operation Trigger Voice (Siri/Google) Assistant Right earpiece Continue touching after beep Stop Voice Assistant Right earpiece Single tap Gaming mode (low latency mode) Task MFT Operation Gaming mode on/off Left earpiece Double tap 10 EN Earpieces LED indicator status Earpieces status Indicator The earpieces are conne
5 Reset the earpieces If you encounter any pairing or connection issue, you can follow the following procedure to reset your earpieces to factory default settings. 1 On your Bluetooth device, go to the Bluetooth menu and remove Philips TAT1209 from the device list. 2 Turn off the Bluetooth function of your Bluetooth device. 3 Return earpieces to charging box and open the lid. 4 Press button on box twice. 5 Follow steps in “Use your earpiecesconnect the earpieces to your Bluetooth device.
7 Notice Declaration of conformity Hereby, TP Vision Europe B.V. declares that the product is in compliance with the essential requirements and other relevant provisions of RED Directive 2014/53/EU and UK Radio Equipment Regulations SI 2017 No 1206. You can �nd the Declaration of Conformity on www.philips.com/support.
Environmental information All unnecessary packaging has been omitted. We have tried to make the packaging easy to separate into three materials: cardboard (box), polystyrene foam (buffer) and polyethylene (bags, protective foam sheet.) Your system consists of materials which can be recycled and reused if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packaging materials, exhausted batteries and old equipment.
Avis de conformité Cet appareil satisfait aux règlements de la FCC partie 15 du Code of Federal Regulations. Son fonctionnement est assujetti aux deux conditions suivantes : 1. Cet appareil ne doit pas causer d’interférence préjudiciable et 2. l’appareil doit accepter toute interférence reçue, y compris les interférences qui peuvent causer un fonctionnement non désiré.
8 Trademarks Bluetooth The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by MMD Hong Kong Holding Limited is under license. Other trademarks and trade names are those of their respective owners. Siri Siri is a trademark of Apple Inc., registered in the U.S. and other countries. Google Google and Google Play are trademarks of Google LLC.
9 Frequently asked questions My Bluetooth earpieces do not turn on. The battery level is low. Charge the earpieces. I cannot pair my Bluetooth earpieces with my Bluetooth device. The Bluetooth is disabled. Enable the Bluetooth feature on your Bluetooth device and turn on the Bluetooth device before you turn on the earpieces. Pairing does not work. • Put both earpieces into charging box. • Make sure you have disabled the Bluetooth function of any previously connected Bluetooth devices.
Charge your headphones regularly. If the headphones are not used for a long time, the rechargeable battery will begin to lose its charge. To avoid this loss, please fully charge the battery at least once every three months.
2023 © MMD Hong Kong Holding Limited. All rights reserved. Speci�cations are subject to change without notice. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license. This product has been manufactured by and is sold under the responsibility of MMD Hong Kong Holding Limited or one of its affiliates, and MMD Hong Kong Holding Limited is the warrantor in relation to this product.