Headphones 1000 Series TAT1215 User manual Register your product and get support at www.philips.
Contents 1 Important safety instructions 2 Hearing Safety General information 2 2 2 Your True wireless earphones 3 What's in the box Other devices Overview of your True wireless earphones 3 Get started 3 3 4 5 Charge the battery 5 Pair the earphones with your Bluetooth device for the first time 5 Pair the earphones with another Bluetooth device 6 4 Use your earphones Connect the earphones to your Bluetooth device Power on/off Manage your calls and music LED indicator status Voice Assistant 8 8
1 Important safety instructions Hearing safety Danger To avoid hearing damage, limit the time you use headphones at high volume and set the volume to a safe level. The louder the volume, the shorter the safe listening time is. Be sure to observe the following guidelines when using your headphones. • Listen at reasonable volumes for reasonable periods of time. • Be careful not to adjust the volume continuously upwards as your hearing adapts.
2 Your True wireless earphones Congratulations on your purchase, and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/support. With this Philips True wireless earphones, you can: • enjoy convenient wireless handsfree calls; • enjoy and control wireless music; • switch between calls and music. Quick start guide Global Warranty Safety leaflet What's in the box Other devices A mobile phone or device (e.g.
Overview of your True wireless earphones LED indicator (earpieces) Multi-function button LED indicator (charging box) Micro USB charging slot
3 Get started Earpieces Place the earpieces in the charging case. Charge the battery Note Before you use your earphones for the first time, place the earpieces in the charging box and charge the battery for 2 hours for optimum battery capacity and lifetime. Use only the original USB charging cable to avoid any damage. Finish your call before charging the earpieces, as connecting the earpieces for charging will power the earpieces off. The earpieces start charging.
Pair the earphones with your Bluetooth device for the first time Make sure that the earphones are fully charged. Auto power on: open the top cover from charging box, the earpieces discharged and the blue LED indicator flashes for 3 times with “power on” voice prompt; Manual power on: on both earpieces press and hold the multi-function buttons for approximately 3s. Turn on the Bluetooth function of your Bluetooth device. Pair the earpieces with your Bluetooth device.
Single earpiece (Mono mode) Take either right or left earpiece out from charging box for mono use. The earpiece will power on automatically. There will be a voice “power on” from earpiece. Note Put both L and R earpieces back into power case and then take the 2 earpieces out to pair and connect Bluetooth again. If still not works, try to reset. Put L and R into power case and press the button for 4 seconds until the white LED flashes.
4 Use your earphones Connect the earphones to your Bluetooth device Turn on the Bluetooth function of your Bluetooth device. Take both earpieces from charging box. Power on/off Task The earphones will search the last connected Bluetooth device and reconnect to it automatically. If the last connected device is not available, the earphones will enter pairing mode. Tip The earphones cannot connect to more than 1 device at the same time.
Call control Task Multifunc tion button Pick up / Right or left hang up call earpiece Reject an Right or left incoming call earpiece Operation Single tap Press and hold 1s Battery LED indicator on Bluetooth device Voice control Task Trigger Voice (Siri/Google) Assistant Earpieces are fully The LED in charged charging case flashes Charging case is The red LED is fully charged lightening Operation Button Right or left Press twice earpiece A battery indicator will be shown on the screen when connected
5 Reset the earphones If you encounter any pairing or connection issue, you can follow the following procedure to reset your earpieces. On your Bluetooth device, go to the Bluetooth menu and remove Philips TAT1215 from the device list. Turn off the Bluetooth function of your Bluetooth device. Put both earpieces back to charging case. Both earpieces flash white LED. Press and hold both earpieces function button for 4s until earpieces flash twice white LED.
7 Notice Declaration of conformity Hereby, MMD Hong Kong Holding Limited declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. You can find the Declaration of Conformity on www.p4c.philips.com. Remove the integrated battery If there is no collection/recycling system for electronic products in your country, you can protect the environment by removing and recycling the battery before disposing of the earpieces.
Compliance with EMF This product complies with all applicable standards and regulations regarding exposure to electromagnetic fields. Environmental information All unnecessary packaging has been omitted. We have tried to make the packaging easy to separate into three materials: cardboard (box), polystyrene foam (buffer) and polyethylene (bags, protective foam sheet.) Your system consists of materials which can be recycled and reused if disassembled by a specialized company.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) L’appareil ne doit pas produire de brouillage; (2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
8 Trademarks Bluetooth The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by MMD Hong Kong Holding Limited is under license. Other trademarks and trade names are those of their respective owners. Siri Siri is a trademark of Apple Inc., registered in the U.S. and other countries. Google Google and Google Play are trademarks of Google LLC.
9 Frequently asked questions My Bluetooth earpieces do not turn on. The battery level is low. Charge the earpieces. I cannot pair my Bluetooth earpieces with my Bluetooth device. The Bluetooth is disabled. Enable the Bluetooth feature on your Bluetooth device and turn on the Bluetooth device before you turn on the earpieces. Pairing does not work. • Put both earpieces into charging box. • Make sure you have disabled the Bluetooth function of any previously connected Bluetooth devices.
2021 © MMD Hong Kong Holding Limited. All rights reserved. Specifications are subject to change without notice. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license. This product has been manufactured by and is sold under the responsibility of MMD Hong Kong Holding Limited or one of its affiliates, and MMD Hong Kong Holding Limited is the warrantor in relation to this product.
