耳机 5000 系列 TAT5506 用户手册 访问以下网站注册您的产品并获取支持 www.philips.
目录 1 重要安全说明 2 听力安全 一般信息 2 2 2 真无线耳机 3 包装盒内物品 其他设备 真无线蓝牙耳机概述 3 使用入门 电池充电 佩戴方式 首次将耳机与蓝牙设备配对 将耳机与另一个蓝牙设备配对 4 使用耳机 将耳机连接至蓝牙设备 控制 ANC(主动降噪) 开机/关机 管理通话和音乐 语音助手 耳机/充电盒 LED 指示灯状态 3 3 4 5 5 6 6 7 8 8 8 9 9 9 10 5 重置耳机 11 6 技术数据 11 7 注意 12 符合性声明 旧产品和电池的处理 拆除集成式电池 符合电磁场 (EMF) 法规 环保信息 法规遵循注意事项 12 12 12 13 13 13 8 商标 15 9 常见问题解答 16
1 重要安 全说明 一般信息 为避免损坏或故障: 警告 切勿将耳机置于高温环境。 切勿摔落耳机。 听力安全 切勿将耳机置于滴水或溅水环境下。(参考特 定产品的 IP 等级) 切勿将耳机没入水中。 当接口或插座潮湿时,请勿给耳机充电。 切勿使用任何包含酒精、氨水、苯或研磨剂的 清剂清洁产品。 如果需要,请使用软布清洁产品,可用少量的 危险 水或稀释的中性肥皂水将布打湿进行清洁。 为避免听力受损,应限制以高音量使用耳机的时 切勿将集成式电池置于高温环境,如阳光直射 间,并将音量设定在安全级别。音量越大,安全 处、明火或类似环境。 收听的时间越短。 如果电池更换不当,会有爆炸危险。仅使用相 同或同等类型的电池进行更换。 使用耳机时请确保遵循以下准则。 要达到特定的 IP 等级,必须关闭充电插槽盖。 • 在合理时间内以合理音量收听。 如果将电池投入火中或热烤箱中,或将其机械 • 听力适应后,注意不要持续地调高 压碎或切割,会导致爆炸。 如果将电池放在极高温度环境中,会导致爆炸 音量。 • 或引起易燃液体或气体泄漏。 请勿将
2 真无线 耳机 快速入门指南 欢迎购买并使用 Philips 产品!若要充 分享受 Philips 提供的支持,请访问 www.philips.
真无线耳机概述 6 7 8 1 麦克风 2 多功能触控 (MFT) 3 LED 指示灯(耳机) 4 麦克风 5 LED 指示灯(恢复出厂设置) 6 恢复出厂设置按钮 7 USB-C 充电插槽 8 LED 指示灯(充电盒) 4 中文
3 使用入门 电池充电 注意 提示 使用耳机之前,请将耳机放入充电盒中,为电池充 电 2 个小时,这样可确保最佳的电池电量和寿命。 通常,通过 USB 给耳机或充电盒充满电需要 2 个 只能使用原装 USB-C 充电线,以免造成任何损坏。 小时。 结束通话后再充电。将耳机连接到充电器,耳机将 自动关机。 无线充电器 (不随附无线充电器) 充电盒内置有无线充电线圈。您可以使用无线 充电器或其他具有无线充电器功能的设备为电 充电盒 池充电。 将 USB-C 充电线的一端插入充电盒,另 警告 一端插入电源。 无线充电注意事项 当充电盒和无线充电器之间有金属、磁铁等导电材 料时,请勿将充电盒放在无线充电器上。 充电盒应远离高温和水源。充电过程中充电盒可能 会发热。这是正常现象。 用无线充电器给电池充电。 提示 充电盒用作便携式备用电池为耳机充电。充电盒 充满电后,可为耳机充满电 3 次。 • 将耳机放在充电盒中 • 合上充电盒盖 • 将充电盒放在无线充电器的中心位置 • 充满电后,将充电盒从无线充电器上取下 耳机 将耳机放在充电盒中。 •
佩戴方式 首次将耳机与蓝牙设备配对 选择合适耳塞以获得最佳贴合感 1 确保耳机已充满电且已关闭电源。 牢固紧密的贴合将提供最佳音质和降噪效果 2 打开充电盒上盖。 1 测试佩戴哪种尺寸的耳塞音质最佳、感 觉最舒适。 2 有大、中、小 3 种尺寸可供选择。 大 中 小 两个耳机上的 LED 指示灯呈白色 和蓝色交替闪烁 插入耳机 1 2 耳机现在处于配对模式,可以与蓝 检查耳机的左右方向。 牙设备(例如手机)配对 将耳机插入耳朵,轻轻扭转,直至牢固 贴合。 3 打开蓝牙设备的蓝牙功能。 4 将耳机与蓝牙设备配对。请参考蓝牙 设备的用户手册。 注意 开机后,如果耳机找不到之前连接的任何蓝牙设 备,它将自动切换到配对模式。 6 中文
以下示例展示如何将耳机与蓝牙设备配对。 1 打开蓝牙设备的蓝牙功能,选择 将耳机与另一个蓝牙设备 配对 Philips TAT5506。 如果您想将其他蓝牙设备与耳机配对,请确 2 如果提示输入耳机密码,请输入 保之前已配对或连接的任何其他设备的蓝牙 “0000”(4 个零)。具有蓝牙 3.
4 使用耳机 控制 ANC(主动降噪) 启用 ANC 将耳机连接至蓝牙设备 1 2 打开蓝牙设备的蓝牙功能。 打开充电盒盖。 蓝色 LED 指示灯将闪烁 耳机将搜索最后一次连接的蓝牙 通过连按两下右耳机可切换不同的 ANC 模式。 • 将耳机放入耳中时,ANC 功能自动 • 触摸 MFT 两次,将切换到感知模式 • 再次触摸 MFT 两次,将关闭 ANC 激活 功能 设备并与其自动重新连接。如果 上次连接的设备不可用,耳机将 感知模式 ANC 关闭 进入配对模式 提示 ANC 开启 耳机无法同时连接到多个设备。如果您有两个配对的 蓝牙设备,请仅打开您要连接的设备的蓝牙功能。 如果在打开耳机后打开蓝牙设备的蓝牙功能,则必须 转到设备的蓝牙菜单,手动将耳机连接到设备。 提示 摘下耳机,耳机将自动激活睡眠模式。重新戴上耳 机,耳机将返回活动模式。 注意 如果耳机在 3 分钟内未能连接到任何蓝牙设备,耳 机将自动关闭以节省电池寿命。 在某些蓝牙设备中,可能不会自动连接。在这种情 任务 MFT 操作 ANC 开启 右耳机 连按两下 感知模式 右
开机/关机 任务 语音助手 MFT 操作 从充电盒中 打开耳机 取出耳机, 即开机 将耳机放回 关闭耳机 任务 按钮 操作 触发语音 左耳机 按住 2 秒 左耳机 按一下 (Siri/Google) 助手 停用语音助手 充电盒以关 闭耳机 管理通话和音乐 控制音乐 任务 MFT 操作 播放或暂停 音乐 右耳机 按住 1 秒 下一曲目 右耳机 连按三下 调节音量 通过手机 控制 通话控制 任务 MFT 操作 接听/在通话 右耳机 连按两下 右耳机 按住 1 秒 之间切换 挂断电话/ 拒接来电 9 中文
耳机 LED 指示灯状态 充电盒 LED 指示灯状态 耳机状态 指示灯 充电时 指示灯 耳机连接到蓝牙设 白色 LED 指示灯每 电池电量低 琥珀色 LED 指示灯 备 5 秒闪烁一次 耳机配对准备就绪 LED 指示灯交替闪 亮起 电池电量相对充足 亮起 烁蓝色和白色 耳机已打开但未连接 白色 LED 指示灯每 至蓝牙设备 1 秒闪烁一次(3 分 钟后自动关闭) 电池电量低(耳机) 蓝色 LED 指示灯每 5 秒闪烁 2 次 电池已充满电(充 请参阅充电盒 电盒) LED 指示灯 10 中文 白色 LED 指示灯 使用中,盖子打开 指示灯 电池电量低 琥珀色缓慢闪烁 4 个周期 电池电量相对充足 关闭
5 将耳机恢复出厂 6 技术数据 设置 如果遇到任何配对或连接问题,可以按照以 下步骤将耳机重置为出厂默认设置。 1 转到蓝牙设备的蓝牙菜单,从设备列表 中删除 Philips TAT5506。 2 关闭蓝牙设备的蓝牙功能。 3 将耳机放回充电盒,然后打开盖子。 4 5 将充电盒上的按钮连按两下。 按照“使用耳机 — 将耳机连接至蓝牙设 备”中的步骤进行操作。 6 将耳机与您的蓝牙设备配对,选择 Philips TAT5506。 音乐播放时间(ANC 开启):7+21 小时 音乐播放时间(ANC 关闭):8+24 小时 待机时间:55 小时 充电时间:2 小时 两个耳机均装有 55 mAh 锂离子电池, 蓝牙版本:5.2 兼容的蓝牙配置协议: 充电盒装有 550 mAh 锂离子电池 • HFP(免提配置协议) • A2DP(高级音频传输协议) • AVRCP(音视频远程控制协议) 支持的音频编解码器:SBC、AAC 频率范围:2.402-2.
7 注意 符合性声明 MMD Hong Kong Holding Limited 特此声 明,本产品符合指令 2014/53/EU 中的基本 要求和其他相关规定。您可登录 拆除集成式电池 如果您所在的国家/地区未设立电子产品的 收集/回收系统,则请在处置耳机之前取出 和回收电池以保护环境。 • 在取出电池之前,确保耳机已与充电盒 断开连接。 www.p4c.philips.
符合电磁场 (EMF) 法规 但是,无法保证在特定设施中不会产生干 本产品符合有关电磁场暴露的所有适用标 产生有害干扰(可以通过关闭和打开设备 准和法规。 来确定),则鼓励用户尝试通过以下一种 扰。如果此设备确实对无线电或电视接收 或多种措施来消除干扰: 环保信息 • 重新调整或摆放接收天线 • 增大设备与接收器之间的距离 已省略所有不必要的包装。我们努力使包 • 将设备连接到与接收器所连接电路不同 • 咨询经销商或经验丰富的无线电/电视 装易于分成三种材料:纸板(盒)、泡沫 塑料(缓冲物)和聚乙烯(袋子、保护泡 沫板)。 的电路上的插座 技术人员以寻求帮助 您的系统中包含可回收利用的材料(如果 由专业公司拆卸)。请遵守当地有关包装 FCC 辐射暴露声明: 材料、废电池和旧设备的处理规定。 本设备符合针对不受控环境规定的 FCC 辐 射暴露限制。 法规遵循注意事项 其发射器不得与任何其他天线或发射器放置 在同一地点或一起使用。 本设备符合 FCC 规则第 15 部分的规定。 操作必须遵守以下两个条件: 警告:未经合规方明确批准,用户擅自更改 1.
CAN ICES-3(B)/NMB-3(B) IC 辐射暴露声明: 本设备符合加拿大针对不受控环境规定的辐 射暴露限制。 其发射器不得与任何其他天线或发射器放置 在同一地点或一起使用。 14 中文
8 商标 蓝牙 Bluetooth® 文字标记和徽标是 Bluetooth SIG,Inc. 的注册商标,MMD Hong Kong Holding Limited 对此类标记的任何使用均已 获得许可。 其他商标和商品名称均为其各自所有 者的商标和商品名称。 Siri Siri 是 Apple Inc. 在美国和其他国家/地区 的注册商标。 Google Google 和 Google Play 是 Google LLC.
9 常见问题 解答 我的蓝牙耳机已连接至支持蓝牙立体声的手 机,但音乐只能通过手机扬声器播放。 请参考手机的用户手册。选择通过耳机收听 音乐。 蓝牙耳机无法打开。 电池电量不足。给耳机充电。 音质太差,可听到爆音。 • 缩短耳机与蓝牙设备之间的距离,或移 蓝牙耳机无法与蓝牙设备配对。 蓝牙功能未开启。打开耳机之前,打开蓝牙 设备并开启设备上的蓝牙功能。 无法配对。 • 将两个耳机放入充电盒。 • 确保已禁用之前连接的任何蓝牙设备的 蓝牙功能。 • 在蓝牙设备上,从蓝牙列表中删除 “Philips TAT5506”。 • 将耳机配对(参见第 6 页的“首次将耳机 与蓝牙设备配对”)。 蓝牙设备无法找到耳机。 • 耳机可能连接至之前配对的设备。关闭 已连接的设备,或将其移出连接范围。 • 配对可能已重置,或耳机之前已与其他 设备配对。按照用户手册中的说明将耳 机与蓝牙设备重新配对。(参见第 6 页 的“首次将耳机与蓝牙设备配对”)。 16 中文 蓝牙设备超出连接范围。 开两者之间的障碍物。 • 给耳机充电 手机传输很慢时,或者根本无法进行音频传 输时,音质非常差。 确保
2021 © MMD Hong Kong Holding Limited.保留所有权利。规格随 时可能变更,恕不另行通知。Philips 和 Philips 盾牌微标是 Koninklijke Philips N.V. 的注册商标,使用已获许可。本产品由 MMD Hong Kong Holding Limited 或其联属公司制造并负责销售, MMD Hong Kong Holding Limited 为本产品的保证人。所有其他公 司和产品名称可能是其各自关联公司的商标。 UM_TAT5506_00_CN_V1.