Headphones 8000 Series TAT8506 User manual Register your product and get support at www.philips.
Contents 1 Important safety instructions 2 Hearing safety General information 2 2 2 Your True wireless earpieces What's in the box Other devices Overview of your True wireless earpieces 3 Get started Charge the battery How to wear Pair the earpieces with your Bluetooth device for the first time Pair the earpieces with another Bluetooth device 4 Use your earpieces Connect the earpieces to your Bluetooth device Control ANC (Active Noise Cancellation) Power on/off Manage your calls and music Voice Assis
1 Important safety instructions Hearing safety Danger To avoid hearing damage, limit the time you use headphones at high volume and set the volume to a safe level. The louder the volume, the shorter the safe listening time is. Be sure to observe the following guidelines when using your headphones. • Listen at reasonable volumes for reasonable periods of time. • Be careful not to adjust the volume continuously upwards as your hearing adapts.
2 Your True wireless earpieces Congratulations on your purchase, and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/support.
Overview of your True wireless earpieces 1 2 3 4 5 6 1 Multi-function touch (MFT) 2 LED indicator (BT pairing and factory reset) 3 LED indicator (earpieces) 4 Bluetooth pair button 5 LED indicator (battery state or charging state) 6 USB-C charging slot 4 EN
3 Get started Charge the battery Note Before you use your headphones, place them in the charging box and charge the battery for 2 hours for optimum battery capacity and lifetime. Use only the original USB-C charging cable to avoid any damage. Finish your call before charging. Connecting the earpieces to charge will power them off. Charging Box Plug one end of the USB-C cable into the charging box and the other end into the power source.
How to wear Select suitable ear tips for optimum fit A tight, secure fit will provide the best sound quality and noise-cancellation. 1 2 Test which ear tip provides you with the best sound and wearing comfort. Pair the earpieces with your Bluetooth device for the first time 1 Make sure that the earpieces are fully charged and powered off. 2 2 Comply™ foam ear tip covers and 5 other sizes of silicone ear tip covers are provided: extra large, large, medium, small and extra small.
The following example shows you how to pair the earpieces with your Bluetooth device. 1 2 Turn on the Bluetooth function of your Bluetooth device, select Philips TAT8506. Enter the earpieces' password “0000” (4 zeros) if prompted. For those devices featuring Bluetooth 3.0 or higher, there is no need to enter a password.
4 Use your earpieces Connect the earpieces to your Bluetooth device Control ANC (Active Noise Cancellation) Enable ANC Different ANC modes can be toggled via double tapping on the right earpiece. • 1 Turn on the Bluetooth function of your Bluetooth device. 2 Open the charging box cover. The blue LED flashes. The earpieces will search the last connected Bluetooth device and reconnect to it automatically.
Voice Assistant Power on/off Task MFT Operation Turn the earpieces on Take earpieces out of the charging box to power on Turn the earpieces off Put earpieces back into the charging box to power off Manage your calls and music Task Button Operation Trigger Voice (Siri/Google) Assistant Left earpiece Tap and hold 2 seconds Stop Voice Assistant Left earpiece Single Tap Use Voice Assistant function (via Google App) Before using this function, please install Google App onto your Android smartph
Earpieces LED indicator status Charging box LED indicator status Earpieces status Indicator When charging Indicator The earpieces are connected to a Bluetooth device The earpieces are ready for pairing White LED blinks every 5 seconds Battery low Amber LED lights up Relative adequate battery White LED lights up In use and cover is open Indicator Battery low Amber slowly blinks for 4 cycles Relatively adequate battery Off The earpieces are on but not connected to a Bluetooth device The LED
5 Reset the earpieces If you encounter any pairing or connection issue, you can follow the following procedure to reset your earpieces to factory default settings. 1 On your Bluetooth device, go to the Bluetooth menu and remove Philips TAT8506 from the device list. 2 Turn off the Bluetooth function of your Bluetooth device. 3 Return earpieces to charging box and open the lid. 4 Press button on box twice. 5 Follow steps in “Use your earpiecesconnect the earpieces to your Bluetooth device.
7 Notice Declaration of conformity Hereby, MMD Hong Kong Holding Limited declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. You can find the Declaration of Conformity on www.p4c.philips.com. Remove the integrated battery If there is no collection/recycling system for electronic products in your country, you can protect the environment by removing and recycling the battery before disposing of the earpieces.
Compliance with EMF This product complies with all applicable standards and regulations regarding exposure to electromagnetic fields. Environmental information All unnecessary packaging has been omitted. We have tried to make the packaging easy to separate into three materials: cardboard (box), polystyrene foam (buffer) and polyethylene (bags, protective foam sheet.) Your system consists of materials which can be recycled and reused if disassembled by a specialized company.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) L’appareil ne doit pas produire de brouillage; (2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
8 Trademarks Bluetooth The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by MMD Hong Kong Holding Limited is under license. Other trademarks and trade names are those of their respective owners. Siri Siri is a trademark of Apple Inc., registered in the U.S. and other countries. Google Google and Google Play are trademarks of Google LLC.
9 Frequently asked questions My Bluetooth earpieces do not turn on. The battery level is low. Charge the earpieces. I cannot pair my Bluetooth earpieces with my Bluetooth device. The Bluetooth is disabled. Enable the Bluetooth feature on your Bluetooth device and turn on the Bluetooth device before you turn on the earpieces. Pairing does not work. • Put both earpieces into charging box. • Make sure you have disabled the Bluetooth function of any previously connected Bluetooth devices.
2021 © MMD Hong Kong Holding Limited. All rights reserved. Specifications are subject to change without notice. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license. This product has been manufactured by and is sold under the responsibility of MMD Hong Kong Holding Limited or one of its affiliates, and MMD Hong Kong Holding Limited is the warrantor in relation to this product.