In Ear 1000 Series TAUT102 User manual Register your product and get support at www.philips.
Contents 1 2 3 4 Important safety instructions 2 Hearing Safety General information 2 2 Your Bluetooth wireless earpieces 3 What's in the box Other devices Overview of your Bluetooth wireless earpieces 3 3 9 Trademarks 13 Bluetooth Siri Google 13 13 13 Frequently asked questions 14 4 Get started 5 Charge the battery Battery LED indicator on Charging case Pair the earpieces with your Bluetooth device at the fist time Single earpieces pairing (Mono mode) Pair the earpieces with another Blu
11 Important safety instructions General information To avoid damage or malfunction: Caution Hearing Safety Danger •• To avoid hearing damage, limit the time you use headphones at high volume and set the volume to a safe level. The louder the volume, the shorter the safe listening time is. Be sure to observe the following guidelines when using your earpieces. •• Listen at reasonable volumes for reasonable periods of time.
22 Your Bluetooth wireless earpieces Congratulations on your purchase, and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/welcome. With this Philips wireless earpieces, you can: •• enjoy convenient wireless handsfree calls; •• enjoy and control wireless music; •• switch between calls and music. What's in the box USB charging cable (for charging only) Quick start guide Other devices A mobile phone or device (e.g.
Overview of your Bluetooth wireless earpieces Microphone and LED indicator (earphone) 4 EN Multi-function buttons LED indicator (charging case) Micro USB charging slot
33 Get started Charge the battery Note •• Before you use your earpieces for the rst time, place the earpieces in the charging case and charge the battery for 2 hours for optimum battery capacity and lifetime. •• Use only the original USB charging cable to avoid any damage. •• Finish your call before charging the earpieces, as connecting the earpieces for charging will power the earpieces off.
Pair the earpieces with your Bluetooth device at the fist time 1 ake sure that the earpieces is fully M charged. 2 Auto power on: open the charging capsule, the earpieces discharged and the blue LED indicator flash for 3 times with “power on” voice prompt; Manual power on: on both earpieces press and hold the multi-function buttons for approxinmately 3s. 3 Turn on the Bluetooth function of your Bluetooth device. 4 air the earpieces with your Bluetooth P device.
Single earpieces pairing (Mono mode) 1 Take the right earpieces (“Master device”) from the charging case, the earpiece will power on automatically. There will be a voice “Power on” from right earpieces. 44 Use your earpieces Connect the earpieces to your Bluetooth device 1 Turn on the Bluetooth function of your Bluetooth device.. 2 Turn on the Bluetooth function on your device, search for “Philips UT102” tap to connect. (Please refer to P.
Call control Power on/off Task Task Multifunction Operation button Turn the earpieces on. Right and left Take both earpieces earpieces from the charging case or press and hold for 3s. Turn the earpieces off. Place both earpieces in charging case. Right/Left earpieces Press and hold for 5s.
Battery LED indicator on earpieces status It will show a battery indicator on Bluetooth device after connected to earpieces. 55 Factory reset the earpieces If you encounter any pairing or connection issue, you can follow the following procedure to factory reset your earpieces. 1 On your Bluetooth device, go to the Bluetooth menu and remove Philips UT102 from the device list. How to wear 2 Turn off the Bluetooth function of your Bluetooth device. 3 Put both earpieces back to charging case.
66 Technical data Earpieces •• •• •• •• •• •• •• •• •• •• •• Music time: 3 hours (additional 9 hrs with charging case) Talk time: 2.5 hours (additional 7.5 hrs with charging case) Standby time: 50 hours Charging time: 2 hours Rechargeable lithium ion battery: 40 mAh on each earpiece Bluetooth version: 5.0 Compatible Bluetooth profiles: •• HSP (Hands-Free Profile-HFP) •• A2DP (Advanced Audio Distribution Profile) •• AVRCP (Audio Video Remote Control Profile) Supported audio codec: SBC Frequency range: 2.
77 Notice Declaration of conformity Hereby, MMD Hong Kong Holding Limited declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. You can find the Declaration of Conformity on www.p4c.philips.com. Remove the integrated battery If there is no collection/recycling system for electronic products in your country, you can protect the environment by removing and recycling the battery before disposing the headphones.
Environmental information All unnecessary packaging has been omitted. We have tried to make the packaging easy to separate into three materials: cardboard (box), polystyrene foam (buffer) and polyethylene (bags, protective foam sheet.) Your system consists of materials which can be recycled and reused if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packaging materials, exhausted batteries and old equipment.
88 Trademarks Bluetooth The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by MMD Hong Kong Holding Limited is under license. Other trademarks and trade names are those of their respective owners. Siri Siri is a trademark of Apple Inc., registered in the U.S and other countries. Google Google is a trademark of Google LLC. The Google Assistant is not available in certain languages and countries.
99 Frequently asked questions My Bluetooth earpieces does not turn on. The battery level is low. Charge the earpieces. I cannot pair my Bluetooth earpieces with my Bluetooth device. The Bluetooth is disabled. Enable the Bluetooth feature on your Bluetooth device and turn on the Bluetooth device before you turn on the earpieces. Pairing does not work. • Put both earpieces into charging case. • Make sure you have disabled the Bluetooth function of any previously connected Bluetooth devices.
I hear but cannot control music on my Bluetooth device (e.g. play/pause/skip forward/ backward). Make sure the Bluetooth audio source supports AVRCP (see ‘Technical data’ on page 10). The volume level of the earpieces is toot low. Some Bluetooth devices cannot link the volume level with the earpieces through volume sync. In this case, you have to adjust the volume on your Bluetooth device independently to achieve an appropriate volume level.
Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license.This product has been manufactured by and is sold under the responsibility of MMD Hong Kong Holding Limited or one of its affiliates, and MMD Hong Kong Holding Limited is the warrantor in relation to this product. UM_TAUT102_00_EN_V1.