INTEGRATED CIRCUITS DATA SHEET TDA1563Q 2 × 25 W high efficiency car radio power amplifier Product specification Supersedes data of 1998 Jul 14 File under Integrated Circuits, IC01 2000 Feb 09
Philips Semiconductors Product specification 2 × 25 W high efficiency car radio power amplifier TDA1563Q FEATURES GENERAL DESCRIPTION • Low dissipation due to switching from Single-Ended (SE) to Bridge-Tied Load (BTL) mode The TDA1563Q is a monolithic power amplifier in a 17-lead DIL-bent-SIL plastic power package. It contains two identical 25 W amplifiers. The dissipation is minimized by switching from SE to BTL mode when a higher output voltage swing is needed.
Philips Semiconductors Product specification 2 × 25 W high efficiency car radio power amplifier TDA1563Q BLOCK DIAGRAM VP1 handbook, full pagewidth VP2 5 13 + SLAVE CONTROL 10 − − MUTE IN2− 16 − 17 + OUT2+ + VI IN2+ 11 IV OUT2− − VI 60 kΩ CIN 25 kΩ 3 + 60 kΩ VP 4 Vref − CSE + 60 kΩ IN1− IN1+ 60 kΩ + VI 2 + 1 − − + VI 7 IV − SLAVE CONTROL 8 + TDA1563Q CLIP AND DIAGNOSTIC STANDBY LOGIC 6 12 14 15 9 MGR173 MODE SC DIAG Fig.1 Block diagram.
Philips Semiconductors Product specification 2 × 25 W high efficiency car radio power amplifier TDA1563Q PINNING SYMBOL PIN DESCRIPTION handbook, halfpage IN1+ 1 non-inverting input 1 IN1+ 1 IN1− 2 inverting input 1 IN1− 2 CIN 3 common input CIN 3 CSE 4 VP1 5 MODE 6 OUT1− 7 OUT1+ 8 GND 9 CSE 4 electrolytic capacitor for SE mode VP1 5 supply voltage 1 MODE 6 mute/standby/operating OUT1− 7 inverting output 1 OUT1+ 8 non-inverting output 1 GND 9 ground OUT2−
Philips Semiconductors Product specification 2 × 25 W high efficiency car radio power amplifier To avoid plops during switching from ‘mute’ to ‘on’ or from ‘on’ to ‘mute/standby’ while an input signal is present, a built-in zero-crossing detector only allows switching at zero input voltage. However, when the supply voltage drops below 6 V (e.g. engine start), the circuit mutes immediately, avoiding clicks from the electronic circuit preceding the power amplifier.
Philips Semiconductors Product specification 2 × 25 W high efficiency car radio power amplifier TDA1563Q LIMITING VALUES In accordance with the Absolute Maximum Rating System (IEC 134). SYMBOL VP PARAMETER CONDITIONS supply voltage MIN. MAX. UNIT operating − 18 V non-operating − 30 V load dump; tr > 2.
Philips Semiconductors Product specification 2 × 25 W high efficiency car radio power amplifier TDA1563Q DC CHARACTERISTICS VP = 14.4 V; Tamb = 25 °C; measured in Fig.7; unless otherwise specified. SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT Supplies VP supply voltage note 1 6 14.4 18 V RL = ∞ Iq(tot) total quiescent current − 95 150 mA Istb standby current − 1 50 µA VC average electrolytic capacitor voltage at pin 4 − 7.
Philips Semiconductors Product specification 2 × 25 W high efficiency car radio power amplifier Vmode 18 handbook, halfpage Operating 4 3 Mute 2 1 Standby 0 MGR176 Fig.4 Switching levels of the mode select switch.
Philips Semiconductors Product specification 2 × 25 W high efficiency car radio power amplifier TDA1563Q AC CHARACTERISTICS VP = 14.4 V; RL = 4 Ω; CSE = 1000 µF; f = 1 kHz; Tamb = 25 °C; measured in Fig.7; unless otherwise specified. SYMBOL Po PARAMETER output power THD total harmonic distortion CONDITIONS MIN. TYP. MAX. UNIT THD = 0.5% 15 19 − W THD = 10% 23 25 − W EIAJ − 38 − W VP = 13.2 V; THD = 0.5% − 16 − W VP = 13.2 V; THD = 10% − 20 − W Po = 1 W; note 1 − 0.
Philips Semiconductors Product specification 2 × 25 W high efficiency car radio power amplifier TDA1563Q handbook, halfpage Io handbook, halfpage V o 10 µs max MGR177 t 0 short circuit removed max short circuit to ground DIAG CLIP 0 50 ms 0 t 50 ms maximum current 50 ms t short circuit to supply pins MGR178 Fig.5 Clip detection waveforms. 2000 Feb 09 Fig.6 Protection waveforms.
Philips Semiconductors Product specification 2 × 25 W high efficiency car radio power amplifier TDA1563Q TEST AND APPLICATION INFORMATION handbook, full pagewidth VP1 VP2 5 13 220 nF 2200 µF TDA1563Q − 0.5Rs 100 nF 3.9 Ω 10 OUT2− IN2− 16 + 100 nF 220 nF 4Ω − 0.5Rs IN2+ 17 220 nF 3.9 Ω 11 OUT2+ + 60 kΩ 60 kΩ Vref 25 kΩ CIN 3 4 CSE 1000 µF 1 µF 0.5Rs 60 kΩ 60 kΩ IN1− 2 + 7 OUT1− 220 nF − 4Ω 0.5Rs IN1+ 1 3.9 Ω 100 nF + 8 OUT1+ 3.
Philips Semiconductors Product specification 2 × 25 W high efficiency car radio power amplifier TDA1563Q 76.20 handbook, full pagewidth 35.56 + − RL-98 Out2 Out2 − − Clip − In1 + gnd + 2.5% Mode On Off In2 + 10% Clip Mute Vp GND Prot gnd TDA1563Q MGR189 Dimensions in mm. Fig.8 PCB layout (component side) for the application of Fig.7.
Philips Semiconductors Product specification 2 × 25 W high efficiency car radio power amplifier TDA1563Q 76.20 handbook, full pagewidth 35.56 2× 25 W high efficiency Out2 17 220 nF 220 nF Out1 1 1 µF 220 nF In2 In1 GND Vp MGR190 Dimensions in mm. Fig.9 PCB layout (soldering side) for the application of Fig.7.
Philips Semiconductors Product specification 2 × 25 W high efficiency car radio power amplifier TDA1563Q MBH692 25 Pd (W) MBH693 25 Pd (W) handbook, halfpage handbook, halfpage 20 20 (1) (1) 15 15 (2) 10 10 5 5 0 (2) 0 0 2 4 6 8 Po (W) 10 2.2 µF 3.3 kΩ 330 Ω 91 nF 2.2 µF 3.3 kΩ 470 nF 68 nF 10 kΩ MGC428 Fig.12 IEC-268 filter. 2000 Feb 09 6 8 Po (W) 10 Fig.11 Dissipation; pink noise through IEC-268 filter. Fig.10 Dissipation; sine wave driven.
Philips Semiconductors Product specification 2 × 25 W high efficiency car radio power amplifier TDA1563Q handbook, full pagewidth VP1 VP2 5 13 220 nF 2200 µF VP TDA1563Q − 100 nF 3.9 Ω 10 OUT2− IN2− 16 + 100 nF 220 nF 4Ω − IN2+ 17 220 nF + 60 kΩ 60 kΩ Vref 25 kΩ CIN 3 4 CSE 1000 µF 1 µF IEC-268 FILTER 60 kΩ 60 kΩ IN1− 2 pink noise 3.9 Ω 11 OUT2+ + 7 OUT1− 220 nF − 3.9 Ω 4Ω IN1+ 1 100 nF + 8 OUT1+ 3.
Philips Semiconductors Product specification 2 × 25 W high efficiency car radio power amplifier MDA845 150 TDA1563Q MDA844 250 Ip handbook, halfpage handbook, halfpage Iq (mA) (mA) 200 100 150 100 50 50 0 0 0 16 8 Vp (V) 24 0 Vms = 5 V; RI = ∞. 2 4 6 Vms (V) VP = 14.4 V; Vi = 25 mV Fig.14 Quiescent current as a function of VP. Fig.15 IP as a function of Vms (pin 3).
Philips Semiconductors Product specification 2 × 25 W high efficiency car radio power amplifier TDA1563Q MDA841 10 MDA840 28 handbook, halfpage handbook, halfpage Gv (dB) THD + N (%) 26 (1) 1 24 (2) 10−1 22 10−2 10 102 103 104 f (Hz) 20 10 105 (1) Po = 10 W. (2) Po = 1 W. 103 104 105 f (Hz) 106 Vi = 100 mV. Fig.18 THD + noise as a function of frequency. Fig.19 Gain as a function of frequency.
Philips Semiconductors Product specification 2 × 25 W high efficiency car radio power amplifier MDA846 0.8 handbook, halfpage Po (W) 0.6 0.4 0.2 0 0 8 16 Vp (V) 24 Vi = 70 mV. Fig.22 AC operating as a function of VP.
Philips Semiconductors Product specification 2 × 25 W high efficiency car radio power amplifier TDA1563Q handbook, full pagewidth MGL914 VP Vload 0 −VP VP Vmaster 1/2 VP 0 VP Vslave 1/2 VP 0 0 1 2 See Fig.7: Vload = V7 − V8 or V11 − V10 Vmaster = V7 or V11 Vslave = V8 or V10 Fig.23 Output waveforms.
Philips Semiconductors Product specification 2 × 25 W high efficiency car radio power amplifier TDA1563Q 5. Connect the supply decoupling capacitors of 220 nF as closely as possible to the TDA1563Qs. APPLICATION NOTES Example of the TDA1563Q in a car radio system solution 6. Place the tracks of the differential inputs as close together as possible. If disturbances are injected at the inputs, they will be amplified 20 times. Oscillation may occur if this is not done properly.
Philips Semiconductors Product specification 2 × 25 W high efficiency car radio power amplifier TDA1563Q (3) handbook, full pagewidth (3) Car-audio chip-set demonstrator TDA3617J TDA1563Q + TDA1563Q + Rear − Front + FL 2.
Philips Semiconductors Product specification 2 × 25 W high efficiency car radio power amplifier TDA1563Q VOLTAGE REGULATOR handbook, full pagewidth Ven1 MICROCONTROLLER VBATT 6 4.7 kΩ 47 µF VBATT 220 nF 8 1 9 7 GND 5 HOLD Ven2 REG2 power on VP TDA3617J GND Ven3 power 3 2 PLANE GND REG3 5V 47 µF 47 nF 47 nF 10 kΩ GND GND 5V 4.7 kΩ GND 3.3 V DIG 3.3 V ANA BAS16/A6 A error 10 kΩ 1 MΩ BC848B/1k mute GND 4.7 kΩ B diagnostic C 4.7 kΩ 5V 3.3 V DIG clip 3.
Philips Semiconductors Product specification 2 × 25 W high efficiency car radio power amplifier TDA1563Q 100 µH/6A handbook, full pagewidth V battery VBATT GND A GND clip select 2.5% PGND 5V 10% GND B C 2200 µF VBATT PGND (16 V) 220 nF VP1 VP2 MODE CLIP DIAG SC IN2+ D E 10 nF IN2− IN1+ 220 nF 220 nF G 10 nF IN1− CIN H GND 1000 µF 9 CSE 4 15 11 (16 V) OUT2+ OUT+ 14 3.9 Ω 12 17 10 16 OUT− 3.9 Ω 100 nF TDA1563Q PGND 3.
Philips Semiconductors Product specification 2 × 25 W high efficiency car radio power amplifier TDA1563Q Advantages of high efficiency • Power conversion improvement (power supply) Usually, the fact that the reduction of dissipation is directly related to supply current reduction is neglected. One advantage is less voltage drop in the whole supply chain. Another advantage is less stress for the coil in the supply line.
Philips Semiconductors Product specification 2 × 25 W high efficiency car radio power amplifier TDA1563Q INTERNAL PIN CONFIGURATIONS PIN 1, 2, 16, 17 and 3 NAME EQUIVALENT CIRCUIT IN1+, IN1−, IN2−, IN2+ and CIN VP1, VP2 VP1, VP2 1, 2, 16, 17 3 MGR182 4 CSE VP1 VP2 4 MGR183 6 MODE 6 MGR184 7, 11 OUT1−, OUT2+ VP1, VP2 7, 11 4 MGR185 2000 Feb 09 25
Philips Semiconductors Product specification 2 × 25 W high efficiency car radio power amplifier PIN 8, 10 NAME OUT1+, OUT2− TDA1563Q EQUIVALENT CIRCUIT VP1, VP2 8, 10 4 MGR186 12 SC VP2 12 MGR187 14, 15 PROT, CLIP VP2 14, 15 MGR188 2000 Feb 09 26
Philips Semiconductors Product specification 2 × 25 W high efficiency car radio power amplifier TDA1563Q PACKAGE OUTLINE DBS17P: plastic DIL-bent-SIL power package; 17 leads (lead length 12 mm) SOT243-1 non-concave Dh x D Eh view B: mounting base side d A2 B j E A L3 L Q c 1 v M 17 e1 Z bp e e2 m w M 0 5 10 mm scale DIMENSIONS (mm are the original dimensions) UNIT A A2 bp c D (1) d Dh E (1) e mm 17.0 15.5 4.6 4.4 0.75 0.60 0.48 0.38 24.0 23.6 20.0 19.6 10 12.
Philips Semiconductors Product specification 2 × 25 W high efficiency car radio power amplifier TDA1563Q The total contact time of successive solder waves must not exceed 5 seconds. SOLDERING Introduction to soldering through-hole mount packages The device may be mounted up to the seating plane, but the temperature of the plastic body must not exceed the specified maximum storage temperature (Tstg(max)).
Philips Semiconductors Product specification 2 × 25 W high efficiency car radio power amplifier NOTES 2000 Feb 09 29 TDA1563Q
Philips Semiconductors Product specification 2 × 25 W high efficiency car radio power amplifier NOTES 2000 Feb 09 30 TDA1563Q
Philips Semiconductors Product specification 2 × 25 W high efficiency car radio power amplifier NOTES 2000 Feb 09 31 TDA1563Q
Philips Semiconductors – a worldwide company Argentina: see South America Australia: 3 Figtree Drive, HOMEBUSH, NSW 2140, Tel. +61 2 9704 8141, Fax. +61 2 9704 8139 Austria: Computerstr. 6, A-1101 WIEN, P.O. Box 213, Tel. +43 1 60 101 1248, Fax. +43 1 60 101 1210 Belarus: Hotel Minsk Business Center, Bld. 3, r. 1211, Volodarski Str. 6, 220050 MINSK, Tel. +375 172 20 0733, Fax. +375 172 20 0773 Belgium: see The Netherlands Brazil: see South America Bulgaria: Philips Bulgaria Ltd.
