SVZ142.
SVZ142.comb 4/7/99 6:30 PM Page 2 Return your Warranty Registration Card today to ensure you receive all the benefits you’re entitled to. Once your purchase is registered, you’re eligible to receive all the privileges of owning this product. So complete and return the Warranty Registration Card enclosed with your purchase at once. And take advantage of these important benefits.
SVZ142.comb 4/7/99 6:30 PM Page 3 Introduction 3 Welcome to your VCR owner’s manual. This manual has six sections: Setting Up Your VCR; Description of Controls; Basic Operations; Recording; Playing; and Information You May Need. The instructions explain all of the VCR’s features, which are listed below. You cannot hurt your VCR by trying the features! So read on – and relax.
SVZ142.comb 4/7/99 6:30 PM Page 4 4 Table of Contents Setting Up Your VCR Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Before Using Your VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Hookups Without a Cable Box/Direct Broadcast System . . .
SVZ142.comb 4/7/99 6:30 PM Page 5 Before Using Your VCR 5 Putting Batteries in the Remote Control 1 1 2 2 3 3 Remove the battery compartment lid on the bottom of the remote control by sliding the lid in the direction of the arrow. Insert two AA batteries inside the battery compartment with their + and – ends aligned as indicated. Replace the battery compartment lid.
SVZ142.comb 4/7/99 6:30 PM Page 6 6 Hookups Without a Cable Box/Direct Broadcast System The basic VCR/TV connection – antenna/cable to VCR to TV – is shown below. If you have a Cable Box or Direct Broadcast System, please refer to pages eight - nine. If you have a Stereo TV, please go to page 10. After you hook up the VCR, please go to page 11 to turn on the VCR. 1 Disconnect the antenna or cable from your TV.
SVZ142.comb 4/7/99 6:30 PM Page 7 Hookups Without a Cable Box/Direct Broadcast System (cont’d) 7 3 Connect the RF coaxial cable (supplied) to the OUT jack on the back of the VCR and to the ANTENNA IN Jack on the TV. (You may use either a snap-on type or screw-on type of coaxial cable, whichever you prefer. A snap-on type is supplied.
SVZ142.comb 4/7/99 6:30 PM Page 8 8 Hookups With a Cable Box This connection allows you to view any channel. After you connect the Cable Box, VCR, and TV as shown below, the features described on this page will be available. 3. Use a second RF 1. Connect a Cable signal to coaxial cable to conthe IN Jack on the Cable Box. nect the OUT jack on the VCR to the TV’s IN ANTENNA IN Jack. OUT 75V ANT CAB / LE ANT IN AUDIO OUT IN VIDEO OUT CH3 CH4 2.
SVZ142.comb 4/7/99 6:30 PM Page 9 Hookups With a Cable Box (cont’d) 9 This connection allows you to program an unattended recording of more than one unscrambled channel and to watch one channel while recording another. After you connect the VCR, Cable Box, and TV as shown below, the features on this page will be available. 1. Connect a Cable 2. Use an RF coaxial cable (supplied) to connect signal to the VCR’s the OUT Jack on the VCR to the IN Jack on the ANT(enna) IN Jack. Cable Box.
SVZ142.comb 4/7/99 6:30 PM Page 10 10 Hookups With a Stereo TV 1 antenna or cable to ANT(enna) IN Jack ANT IN AUDIO OUT IN VIDEO VIDEO (yellow) and AUDIO (white) OUT Jacks ● Audio and Video cables are not supplied. OUT CH3 CH4 2 3 Audio and Video IN Jacks on TV Video Cable Audio Cable 1 Connect the antenna or cable to the ANT(enna) IN Jack on the back of the VCR. 2 Connect a video cable to the yellow VIDEO OUT Jack on the back of the VCR.
SVZ142.comb 4/7/99 6:30 PM Page 11 Turning on Your VCR 11 ● Before turning on your VCR, make sure there are batteries in the remote control and the VCR and TV are connected (see pages five - 10). ● You can not set up channels if you are using a Cable Box/DBS. ● The instructions on this page only work when you turn on the VCR for the first time. If there is a power failure or if the VCR is unplugged for more than one minute, you may need to repeat the instructions on this page.
SVZ142.comb 4/7/99 6:30 PM Page 12 12 Automatic Channel Setup Although your VCR may automatically set up the channels you receive when you turn it on for the first time, this function lets you set up channels again. Make sure: ● The VCR is on and is in VCR position. (The VCR/TV light will appear on the display panel. If it does not, press the VCR/TV button once.) 1 Press the MENU button repeatedly until the INITIALIZE menu appears.
SVZ142.comb 4/7/99 6:30 PM Page 13 Automatic Channel Setup (cont’d) 13 Adding/Deleting Channels The channels you no longer receive or seldom watch can be deleted from the memory. You also may add new channels into the memory. Make sure: ● The VCR is on and in VCR position. (The VCR/TV light will appear. If it does not, press the VCR/TV button once.) 1 Press the MENU button repeatedly until the INITIALIZE menu appears.
SVZ142.comb 4/7/99 6:30 PM Page 14 14 Setting the Clock Follow the steps below to set your VCR’s clock. Make sure: ● The VCR is on and in VCR position. (The VCR/TV light will appear. If it does not, press the VCR/TV button once.) 1 Press the MENU button repeatedly until the INITIALIZE menu appears. POWER 2 Press the PLAY button or the STOP button repeatedly to select SETTING CLOCK. Then, press the F.FWD button.
SVZ142.comb 4/7/99 6:30 PM Page 15 Setting the Clock (cont’d) 15 6 While the HOUR space is flashing, press the PLAY button or the STOP button repeatedly until the desired hour appears. Then, press the F.FWD button. SETTING CLOCK MONTH DAY YEAR 03 / 01 SUN 1 9 9 8 HOUR MINUTE 05 : –– AM/PM –– 7 POWER While the MINUTE space is flashing, press the PLAY button or the STOP button repeatedly until the desired minute appears. Then, press the F.FWD button.
SVZ142.comb 4/7/99 6:30 PM Page 16 16 Language Selection Follow the steps below to change the language of the on-screen menus and displays. Make sure: ● The VCR is on and in VCR position. (The VCR/TV light will appear. If it does not, press the VCR/TV button once.) 1 Press the MENU button repeatedly until the INITIALIZE menu appears. INITIALIZE → CHANNEL SET UP SETTING CLOCK LANGUAGE SELECT POWER 2 Press the PLAY button or the STOP button repeatedly to select LANGUAGE SELECT. Then, press the F.
SVZ142.comb 4/7/99 6:30 PM Page 17 On-Screen Status Displays 17 You may access on-screen status displays by pressing the DISPLAY button repeatedly. On-screen status displays may include the current time, channel, and other information. ● Press the DISPLAY button once. The COUNT on-screen status display will appear for five seconds. After five seconds, only the real-time counter will appear on-screen.
SVZ142.comb 4/7/99 6:30 PM Page 18 18 Remote Control Buttons POWER Button Press to turn the VCR on or off. Number Buttons Use to select channels. Channels 1 - 9 ● To select, press 0, then press the channel number you want. For example, to select channel 7, press 0, 7. Channels 100 and above ● To select, press the +100 button, then press the last two digits of the channel you want. For example, to select channel 117, press the +100 button, 1, 7.
SVZ142.comb 4/7/99 6:30 PM Page 19 Remote Control Buttons (cont’d) 19 EJECT Button Press to eject the tape. VCR/TV Button Use to select the signal that your TV receives. ● VCR Position Use to watch a tape, to watch a program while recording it, or to watch a TV broadcast using the CHANNEL o/p or Number buttons. ● TV Position Use to watch TV or to watch one program while recording another. Details are on page 32.
SVZ142.comb 4/7/99 6:30 PM Page 20 20 VCR Display Panel VCR Display Panel Information about VCR operations is displayed here. Cassette Compartment Insert a video cassette tape here. PLAY REW F FWD STOP EJECT REC/OTR POWER POWER VCR/TV VCR/TV POWER POWER Light This light indicates that the power is on. VCR/TV Light This light appears when the VCR is in VCR position. POWER VCR/TV VCR/TV CST. IN CST.
SVZ142.comb 4/7/99 6:30 PM Page 21 Front Panel 21 F.FWD (Fast Forward) Button When tape playback is stopped, press to fast forward the tape at high speed. During tape playback, press to fast forward the tape while the picture stays on-screen. Details are on page 35. Remote Sensor Receives a signal from your remote control so you can operate your VCR from a distance. PLAY Button Press to play a tape. Also, press to release Slow, Search, or Still mode and to return to normal playback.
SVZ142.comb 4/7/99 6:30 PM Page 22 22 Rear Panel ANT(enna) IN Jack Connect your antenna or cable here. Details are on pages six - 10. AUDIO IN Jack Connect a cable coming from the audio out jack of a camcorder, another VCR, or an audio source here. Details are on page 33. AUDIO OUT Jack Connect a cable going to the audio in jack of a camcorder, another VCR, or an audio source here. Details are on page 33.
SVZ142.comb 4/7/99 6:30 PM Page 23 Playing 23 Read and follow the steps below to play a tape. 1 Turn on the TV and set it to channel 3 or 4, whichever channel the CH3/CH4 switch on the back of the VCR is set to. 1 2 Turn on the TV. Insert a tape. 2 Insert a tape in the VCR. The POWER and CST.IN lights will appear. If the tape’s record tab has been removed, the VCR/TV light will appear and playback will begin automatically.
SVZ142.comb 4/7/99 6:30 PM Page 24 24 Recording Read and follow the steps below to record a television program. 1 Turn on the TV; set it to channel 3 or 4, whichever the CH3/CH4 switch on the back of the VCR is set to. 1 2 Turn on the TV. Insert a tape. 2 Insert a tape with its record tab intact (see page five) in the VCR. The POWER and CST.IN lights will appear. 3 3 Press the VCR/TV button so that the VCR/TV light appears.
SVZ142.comb 4/7/99 6:30 PM Page 25 One-Touch Recording 25 The One-Touch Recording function allows you to program an immediate timed recording 30 minutes to eight hours long. Before you begin, make sure: ● Channels are set up. ● The desired recording speed (SP, LP, SLP) has been selected with the SPEED button. ● There is a tape in the VCR. Make sure the tape’s record tab is intact and the tape is long enough to record the program(s). ● The VCR is in VCR position. (The VCR/TV light will appear.
SVZ142.comb 4/7/99 6:30 PM Page 26 26 Timer Recording Follow the steps below to program your VCR to record TV programs while you’re away from home. You can program up to seven timer recordings. For each one, the VCR will turn itself on, record, and turn itself off automatically. Before you begin make sure: ● Channels are set up. ● The clock is set. ● There is a tape in the VCR. Make sure the tape’s record tab is intact and the tape is long enough to record the program(s).
SVZ142.comb 4/7/99 6:30 PM Page 27 Timer Recording (cont’d) 27 4 Press the PLAY button or the STOP button repeatedly until the desired month appears. Then, press the F.FWD button. Next, press the PLAY button or the STOP button repeatedly until the desired day appears. Then, press the F.FWD button. The day of the week will appear automatically. You can not program the VCR to record more than one year in advance.
SVZ142.comb 4/7/99 6:30 PM Page 28 28 Timer Recording (cont’d) 7 Press the PLAY button or the STOP button repeatedly until the desired channel number appears. Then, press the F.FWD button. ● If you are using a standard antenna/cable hookup (as shown on pages six - seven), select the channel of the TV program you want to record. ● If you are recording from line input, select AUX. ● If you are using a Cable Box/DBS, select the Cable Box/DBS output channel (03 or 04).
SVZ142.comb 4/7/99 6:30 PM Page 29 Timer Recording (cont’d) 29 Cancelling a Timer Recording To cancel a timer recording 1 Press the MENU button so that the TIMER PROGRAMMING menu appears. POWER 2 Press the PLAY button or the STOP button until the program number you want to cancel appears on-screen. 3 While the program number is flashing, press the REWIND button to cancel the timer recording. 4 Press the COUNTER RESET/EXIT button to exit.
SVZ142.comb 4/7/99 6:30 PM Page 30 30 Auto Return Follow the steps below to make the VCR rewind to the beginning of the programs after it has finished all timer recordings. Make sure: ● The VCR is on and is in VCR position. (The VCR/TV light will appear. If it does not, press the VCR/TV button once.) 1 Press the MENU button repeatedly until the VCR SET UP menu appears.
SVZ142.comb 4/7/99 6:30 PM Page 31 Auto Satellite Link Using a Satellite Tuner 31 If you connect your VCR to a satellite tuner that has the Electronic Program Guide, the VCR will turn itself on, record, then turn itself off. First, read the owner’s manual of your satellite tuner; then, follow these steps to set up your VCR. Before you begin: ● Use audio and video cables to connect the AUDIO/VIDEO IN jacks on the back of the VCR to the AUDIO/VIDEO OUT jacks on the satellite tuner.
SVZ142.comb 4/7/99 6:30 PM Page 32 32 Recording One Channel/Watching Another 1 Press the RECORD button to start a recording. Details are on page 24. 2 3 4 Select the channel you want to watch at the TV. Set the TV to channel 3 or 4. Press the VCR/TV button to put the VCR in TV position. The VCR/TV light will disappear. 3 POWER Use the TV remote control to select the channel you want to watch at the TV.
SVZ142.comb 4/7/99 6:30 PM Page 33 Rerecording (Tape Duplication) 33 1. Audio cable from AUDIO OUT Jack of VCR 1 to AUDIO IN Jack of VCR 2 VCR 2 - Recording VCR VCR 1 - Playing VCR ANT ANT IN IN AUDIO OUT AUDIO IN VIDEO OUT OUT CH3 CH4 IN VIDEO 2. Video cable from VIDEO OUT Jack of VCR 1 to VIDEO IN Jack of VCR 2 OUT CH3 CH4 3. RF coaxial cable from VCR’s OUT Jack to TV’s ANTENNA IN Jack 1 VCR 1 will play your tape. Insert a prerecorded tape in VCR 1.
SVZ142.comb 4/7/99 6:30 PM Page 34 34 Repeat Play Follow the steps below to program the VCR to play a tape over and over. Make sure: ● The VCR is on and is in VCR position. The VCR/TV light will appear on the front panel. If it does not, press the VCR/TV button once. ● There is a tape in the VCR. 1 Press the MENU button repeatedly until the VCR SET UP menu appears.
SVZ142.comb 4/7/99 6:30 PM Page 35 Special Effects Playback 35 Forward and Reverse Searching (SP/LP/SLP) 1 During tape playback, press and release the F.FWD button or the REWIND button. A fast forward or reverse picture search will begin. 2 To return to playback, press the PLAY button. POWER Super High Speed Searching (LP/SLP) 1 During tape playback, press the F.FWD button or the REWIND button, then press again. The VCR will now search in super high speed.
SVZ142.comb 4/7/99 6:30 PM Page 36 36 Rental Play This function enables you to improve the picture quality when playing worn cassettes such as those rented from a video store. Make sure: ● The VCR is on and is in VCR position. The VCR/TV light will appear. If it does not, press the VCR/TV button once. ● There is a tape in the VCR. 1 During tape playback, press the MENU button repeatedly until the VCR SET UP menu appears.
SVZ142.comb 4/7/99 6:30 PM Page 37 Real-Time Counter Memory 37 Follow the steps below to reset the real-time counter to zero at a tape location you want to refer to later. Make sure: ● The VCR is on and is in VCR position. The VCR/TV light will appear. If it does not, press the VCR/TV button once. ● There is a tape in the VCR. 1 Play, fast forward, or rewind a tape to the location that you would like to refer to later. Press the STOP button to stop the tape.
SVZ142.comb 4/7/99 6:30 PM Page 38 38 Index Search When you make a recording, the VCR places an index mark at the beginning of the recording. Essentially, an index mark is a type of “bookmark” for your tape. This feature is useful if you have several different programs recorded on a single tape. You may skip over programs by following the steps below. Before you begin, make sure: ● The VCR is on and is in VCR position. (The VCR/TV light will appear. If it does not, press the VCR/TV button once.
SVZ142.comb 4/7/99 6:30 PM Page 39 Time Search 39 The Time Search function allows you to go to a specific point on a tape. You will enter the exact amount of playback time that you wish to skip in order to reach the specified point. Make sure: ● The VCR is on and is in VCR position. (The VCR/TV light will appear. If it does not, press the VCR/TV button once.) ● There is a tape in the VCR. 1 Press the MENU button repeatedly until the SEARCH SELECT menu appears.
SVZ142.comb 4/7/99 6:30 PM Page 40 40 Quick Find The Quick Find feature locates the beginning of each recording on a tape, then plays the first portion of the recording at high speed for 30 seconds. After it plays the portion, the VCR fast forwards the tape to the next recording. This process is repeated until the end of the tape is reached, or until you stop the Quick Find. To start a Quick Find, press the QUICK-FIND button on the remote control, or follow the steps below.
SVZ142.comb 4/7/99 6:30 PM Page 41 Automatic Playback Features 41 Automatic Playback When you put a tape in the VCR, the power will come on automatically. If the tape’s record tab is missing, playback will begin. (If a timer recording is set, you may have to press the POWER button to turn on the VCR. Make sure you turn off the VCR for the timer recording later. If you insert a tape without a record tab when a timer recording is set, the VCR will eject the tape.
SVZ142.comb 4/7/99 6:30 PM Page 42 42 Helpful Hints If you are having problems with your product, check this list of problems and possible solutions before requesting service. You may be able to solve the problem yourself. If you need to call a customer service representative, please know the model number and serial number of your product before you call. This information is displayed on the back of the product.
SVZ142.comb 4/7/99 6:30 PM Page 43 Helpful Hints (cont’d) 43 Tape cannot be removed. • Make sure the power plug is completely connected to an AC (alternating current) outlet. • You have set a timer recording. Turn on the VCR power, then eject the tape. Be sure to insert a tape and turn off the VCR for your timer recording. Tape cannot be inserted. • Insert the tape, window side up, with the record tab facing you.
SVZ142.comb 4/7/99 6:30 PM Page 44 44 Glossary AUDIO IN/OUT Jacks: jacks located on the back of the VCR which are used to record audio from another source (IN) or to send audio to another source (OUT). Automatic Channel Setup: process in which the VCR scans all available channels and places the ones you receive in its memory. Then, when you push the CHANNEL (o/p) buttons, you only scan through channels you receive. Bands: settings that allow you to tune channels.
SVZ142.comb 4/7/99 6:30 PM Page 45 Specifications 45 Video Heads Four heads Video Signal EIA standards; NTSC color Antenna VHF/UHF – 75 ohm external antenna terminal VHF Output Signal Channel 3 or 4 (switchable) 75 ohms unbalanced Power Requirement 120V AC; 60Hz Power Consumption 16W Operating Temperature 41°F (5°C) to 104°F (40°C) Relative Humidity 10% to 80% Weight 5.5 lbs. (2.5 kg.
SVZ142.comb 4/7/99 6:30 PM Page 46 46 Limited Warranty VIDEO CASSETTE RECORDER 90 Days Free Labor/One Year Parts Exchange. This product must be carried in for repair. WHO IS COVERED? You must have proof of purchase to receive warranty service. A sales receipt or other document showing that you purchased the product is considered proof of purchase. WHAT IS COVERED? Warranty coverage begins the day you buy your product. For 90 days thereafter, all parts will be repaired or replaced, and labor is free.
SVZ142.comb 4/7/99 6:30 PM Page 47 Index 47 ac power cord ...........................7, 22 accessories.......................................48 ant(enna) in jack................6 - 10, 22 audio in/out jacks .............10, 22, 33 auto return ......................................30 auto satellite link ............................31 automatic playback........................................41 rewind, eject, off ........................41 batteries..............................................
4/7/99 6:30 PM SUPPLIED ACCESSORIES SVZ142.comb Page 48 Check to be sure the items on this page are packed with your VCR. These accessories are provided to help you use or set up your VCR. Remote Control 4835 218 37219 Two “AA” Batteries 4835 138 17012 RF Coaxial Cable, 75 ohm 4835 323 27011 If any of these items are not included, or if you need to replace an item, contact our Service Solutions Group at the address below. Service Solutions Group P.O.