Datasheet

ManualsBrandsPHOENIX CONTACT ManualsD-SUB ConnectorsD-SUB plug 180 ° Number of pins: 9 Screws SUBCON-PLUS M1 1 pc(s)

101610_en_06

INTERFACE

SUBCON-PLUS-PROFIB…

Data sheet

1Description

The D-SUB series SUBCON-PLUS-PROFIB… is specially

designed for use in PROFIBUS systems up to 12 Mbps.

Under field conditions, it allows convenient and fast

connection of the incoming and outgoing bus cable. The

spectrum comprises seven fast connection connectors:

All connectors can be used for PROFIBUS cables with a

solid or stranded copper conductor.

The terminating resistor is already integrated in all versions.

It can be connected externally by means of a slide switch. At

the same time the outgoing bus segment is switched off.

This makes it easy to start up segment by segment while

incorrect terminations are avoided.

In addition, the connector housing with high-quality

shielding guarantees high immunity to interference even at

maximum transmission rates.

A special feature of the 35° angled connector is that the

internal connection unit can be turned round. Whether the

cable is to be inserted from the right or left can thus be

decided on-site. If the angled versions cannot be used, the

SUBCON-PLUS.../AX compact connector with axial cable

entry can be used instead.

The connectors are designed for all standard PROFIBUS

cables with an outside diameter of 8 mm (types A and B). If

the Fast Connect cable is used, work is reduced to a

minimum by using the quick stripping tool, PSM-STRIP-

FC/PROFIB: Strip cable and individual wires, insert in

connector and close housing cover.

Cable entry Connection Programming

interface

35° angled Screw connection Included

35° angled Screw connection Not included

90° angled Screw connection Included

90° angled Screw connection Not included

90° angled IDC connection Included

90° angled IDC connection Not included

Axial Screw connection Not included

If you have any technical problems, which you cannot resolve with the aid of this documentation, please contact

us during the usual office hours at: PSI hotline: +49 - (0) 52 35 - 31 98 90; Fax: +49 - (0) 52 35 - 33 09 99

E-mail: interface-service@phoenixcontact.com

The connectors are specified for cable type A according to EN 50170. Cable type B, also described in EN 50170,

is out-of-date and should no longer be used.

You will find other innovative solutions for PROFIBUS at www.phoenixcontact.com

Make sure you always use the latest documentation.

This can be downloaded from www.phoenixcontact.net/catalog

This data sheet is valid for the products listed on the following page:

Fast connection connector for PROFIBUS systems

Summary of content (12 pages)

PAGE 1
SUBCON-PLUS-PROFIB… Fast connection connector for PROFIBUS systems INTERFACE Data sheet 101610_en_06 1 © PHOENIX CONTACT 2011-01-26 Description The D-SUB series SUBCON-PLUS-PROFIB… is specially designed for use in PROFIBUS systems up to 12 Mbps. Under field conditions, it allows convenient and fast connection of the incoming and outgoing bus cable.
PAGE 2
SUBCON-PLUS-PROFIB… Table of contents 1 2 3 Description .................................................................................................................................................1 Ordering data .............................................................................................................................................2 Fast connection connector SUBCON-PLUS-PROFIB(/PG)SC 2 ...............................................................3 3.1 3.2 3.3 3.
PAGE 3
SUBCON-PLUS-PROFIB… 3 Fast connection connector SUBCON-PLUS-PROFIB(/PG)SC 2 Technical data for SUBCON-PLUS-PROFIB(/PG)/SC 2 Connector 9-pos. D-SUB male connector Programming connection 9-pos. D-SUB socket Cable entry either left or right Connection cross section of screw terminal blocks solid 0.14 mm2 ... 1.5 mm2 stranded 0.14 mm2 ... 1 mm AWG AWG 26-16 Insertion/withdrawal cycles > 200 Cable cross section (max./min.) 8 mm (± 0.4 mm) Mounting screws 4-40 UNC Maximum torque 0.
PAGE 4
SUBCON-PLUS-PROFIB… 3.3 Cable entry Structure 9 The SUBCON-PLUS-PROFIB(/PG)/SC 2 connectors enable cable entry on the left or right. The connector is supplied preassembled for left-hand entry. 1 2 8 3 To ensure reliable operation, observe the recommended stripping lengths according to Figure 4. 4 Connection for cable entry on left 5 7 6 Figure 3 Structure Figure 5 1 2 3 4 5 3.
PAGE 5
SUBCON-PLUS-PROFIB… • Loosen the housing screws and lift off upper housing part (Figure 6). * ! ) Figure 7 • • • • • Cable entry on right (2) Use a screwdriver to pry the PCB out of the upper housing part, inserting screwdriver near cable entry. Place PCB in upper housing part (B in Figure 6) and screw stripped conductors into corresponding connection block contacts. Always connect the incoming bus cable (BUS IN) to the 1A/1B terminal connections (also at start of bus system!).
PAGE 6
SUBCON-PLUS-PROFIB… 4 Fast connection connector SUBCON-PLUS-PROFIB/AX/SC Technical data for SUBCON-PLUS-PROFIB/AX/SC Connector 9-pos. D-SUB male connector Cable entry axial Connection cross section of screw terminal blocks solid 0.14 mm2 ... 1.5 mm2 stranded 0.14 mm2 ... 1 mm AWG 26-16 AWG Insertion/withdrawal cycles > 200 Cable cross section (max./min.) 8 mm (± 0.4 mm) Mounting screws 4-40 UNC Maximum torque 0.4 Nm Temperature range Operation -20 °C ...
PAGE 7
SUBCON-PLUS-PROFIB… 4.3 Structure Connecting 7 B 1 O A 1 N O FF 1 A 2 X /A B 2 FIB RO -P US PL ON BC SU 6 2 3 A 1 B 1 A 2 4 Figure 12 B 2 • • 5 • Figure 10 Structure • 1 2 3 4 Upper housing part Connection block Slide switch Mounting screws 4.4 Connection 5 6 7 Lower housing part Strain relief Housing screws • Connection Strip the cable according to Figure 11. Loosen the housing screws and lift off upper housing part.
PAGE 8
SUBCON-PLUS-PROFIB… 5 Fast connection connector SUBCON-PLUS-PROFIB/90(/PG)/IDC Technical data for SUBCON-PLUS-PROFIB/90(/PG)/IDC Connector 9-pos. D-SUB male connector Programming connection 9-pos. D-SUB socket Interface connection IDC fast connection (insulation displacement connection method) Cable entry 90° angled cable outlet Connection cross section of IDC terminal blocks (single-wire) solid min. 0.32 mm2 stranded min. 0.32 mm2 AWG min.
PAGE 9
SUBCON-PLUS-PROFIB… 5.3 The programming connection of the SUBCON-PLUS-PROFIB/90/PG/IDC variant also integrated allows a programming or service device to be connected without interrupting the bus operation. Structure 4 3 2 1 1A To ensure reliable operation, observe the recommended stripping lengths according to Figure 16. 1B 2A 2B 6 7 Figure 15 5 Setup Upper housing part Housing screw PG connection Slide switch 5.
PAGE 10
SUBCON-PLUS-PROFIB… 6 Fast connection connector SUBCON-PLUS-PROFIB/90(/PG)/SC Technical data for SUBCON-PLUS-PROFIB/90(/PG)/SC Connector 9-pos. D-SUB male connector Programming connection 9-pos. D-SUB socket Interface connection screw connection terminal blocks Cable entry 90° angled cable outlet Connection cross section of screw terminal blocks solid 0.14 mm2 ... 0.04 in2 stranded 0.14 mm2 ... 1.
PAGE 11
SUBCON-PLUS-PROFIB… 6.3 Structure 3 2 The strain relief is integrated in the upper housing parts and is designed for the standard PROFIBUS type A cable. 4 The programming connection of the SUBCON-PLUS-PROFIB/90/PG/SC variant also integrated allows a programming or service device to be connected without interrupting the bus operation. 1 To ensure reliable operation, observe the recommended stripping lengths according to Figure 21.
PAGE 12
SUBCON-PLUS-PROFIB… 7 Termination resistor 7.1 Activating termination resistor and disabling outgoing bus cables ON ON ON OFF OFF OFF OFF OFF OFF OFF ≈ ON OFF ON ON ON OFF Start Finish Figure 23 Termination resistor The termination resistors are activated at the start and finish of the bus system using the slide switch (pos. 2 in Figure 3, pos. 3 in Figure 10 and pos. 4 in Figure 20). The connection terminal blocks (2A/2B) for the outgoing bus cable are disabled at the same time.