Datasheet

ManualsBrandsPHOENIX CONTACT ManualsRack & DIN Rail Mount PSUsTRIO-PS/3AC/24DC/5 DIN Rail Power Supply 24Vdc 5A 120W, 3-Phase

1Description

Primary-switched power supply, 3-phase, output

current 5 A

TRIO-PS/3AC/24DC/5

Data Sheet

INTERFACE

TRIO POWER is the DIN-rail-mountable power supply unit

with basic functions. With an output voltage of 12 V DC,

24 V DC and 48 V DC and 1- and 3-phase versions with 60 W

or 960 W, it is particularly suited for use in series production

in mechanical engineering. The wide-range input and

international certification package allows worldwide

implementation.

The high MTBF of 500,000 h stands for high supply reliability.

The devices can be connected in parallel to increase the

capacity and redundancy.

The clear LED signaling and the device connection with

double terminal block for plus and minus for fast potential

distribution are further advantages of this device series. A

third terminal block simplifies the grounding on the secondary

side. All power supply units are idle proof and short circuit

proof and provide a regulated and adjustable output voltage.

DANGER OF EXPLOSION!

Only remove equipment when it is disconnected and not in the potentially explosive area.

DANGER

Components with dangerously high voltage and high stored energy are located in the device!

Never carry out work on live parts!

Depending on the ambient temperature and the load, the housing can become very hot!

Make sure you always use the the latest documentation.

It can be downloaded at www.download.phoenixcontact.com.

A conversion table is available on the Internet at

www.download.phoenixcontact.com/general/7000_en_00.pdf.

– Reliable power supply unit even at high ambient

temperatures

– No load and short circuiting resistance

– High dielectric strength

– Can be used worldwide in all industrial sectors due to a

wide-range input and an international approval package

– 2-phase operation on AC networks without limitations

103346_en_00

Features

Summary of content (13 pages)

PAGE 1
TRIO-PS/3AC/24DC/5 Primary-switched power supply, 3-phase, output current 5 A INTERFACE Data Sheet 103346_en_00 1 © PHOENIX CONTACT - 05/2008 Description TRIO POWER is the DIN-rail-mountable power supply unit with basic functions. With an output voltage of 12 V DC, 24 V DC and 48 V DC and 1- and 3-phase versions with 60 W or 960 W, it is particularly suited for use in series production in mechanical engineering.
PAGE 2
TRIO-PS/3AC/24DC/5 2 Table of contents 1 Description ..................................................................................................................................1 2 Table of contents.........................................................................................................................2 3 Ordering data .............................................................................................................................. 3 4 Technical data..............
PAGE 3
TRIO-PS/3AC/24DC/5 3 Ordering data Description Type Order No. Pcs. Pkt. Primary-switched power supply, 3-phase, output current 5 A TRIO-PS/3AC/24DC/5 2866462 1 Accessories Type Order No. Pcs. Pkt. Universal wall adapter UWA 182/52 2938235 1 4 Technical data Input data Input nominal voltage range 2x / 3x 400 V AC ... 500 V AC AC input voltage range 320 V AC ... 575 V AC (for 3-phase operation) 2x 360 V AC ... 575 V AC (for 2-phase operation) AC frequency range 45 Hz ...
PAGE 4
TRIO-PS/3AC/24DC/5 Signal output DC OK active Status display "DC OK" LED green / UOUT > 21.5 V: LED lights up General data Insulation voltage input/output 4 kV AC (type test) 2 kV AC (routine test) Insulation voltage input / PE 2 kV AC (type test) 2 kV AC (routine test) Insulation voltage output / PE 500 V DC (routine test) Degree of protection IP20 Class of protection I, with PE connection MTBF > 500 000 h in acc.
PAGE 5
TRIO-PS/3AC/24DC/5 Conformance with EMC directive 2004/108/EC Noise immunity according to EN 61000-6-2 Electrostatic discharge Electromagnetic HF field Fast transients (burst) Surge current loads (surge) Conducted interference Voltage dips EN 61000-4-2 Housing Level 3 Contact discharge 8 kV Discharge in air 8 kV Comments Criterion B EN 61000-4-3 Housing Level 3 Frequency range 80 MHz ...
PAGE 6
TRIO-PS/3AC/24DC/5 5 Structure 5 4 3 + + – – – AC input DC output Potentiometer 22.5 V DC ... 29.5 V DC "DC OK" LED DIN rail adapter Take-up for cable binders TRIO POWER 2 1 2 3 4 5 6 Ou t 24put D V C 5A DC OK A 22 dju .5- st 29 .5V 1 L1 Input Output L2 (L3 [mm2] solid stranded 0.2 - 2.5 0.2 - 2.5 0.2 - 2.5 0.2 - 2.5 AWG 24 - 14 16 - 12 [Nm] Torque 0.4 - 0.5 0.4 - 0.5 ) PE Inp u 40 t 2/3 0-5 A 00 C V 6 Input data Input nominal voltage range 2x / 3x 400 V AC ...
PAGE 7
TRIO-PS/3AC/24DC/5 6 Block diagram L1 L2 (L3) PE 7 Safety notes DANGER OF EXPLOSION! Only remove equipment when it is disconnected and not in the potentially explosive area.
PAGE 8
TRIO-PS/3AC/24DC/5 8 Installation ATTENTION: Module can become damaged In order to guarantee sufficient convection, we recommend observing the following minimum distance to other modules: 5 cm in a vertical direction and 0 cm in a horizontal direction. Ou tp 24 ut D V C 5A DC The power supply unit can be snapped onto all DIN rails in acc. with EN 60715 and must be mounted vertically (connecting terminal blocks on top and bottom). TRIO POWER + + – – – OK A 22 dju .5-2 st 9.
PAGE 9
TRIO-PS/3AC/24DC/5 10 Mounting on DIN rails Assembly A B Position the module with the DIN rail guide on the upper edge of the DIN rail, and snap it in with a downward motion. Removing Pull the snap lever open with the aid of a screwdriver and slide the module out at the lower edge of the DIN rail.
PAGE 10
TRIO-PS/3AC/24DC/5 12 Input ATTENTION: Module can become damaged If an external fuse is triggered, there is most probably a malfunction in the device. In this case, the device must be inspected in the factory! + + – – – TRIO POWER Protection of the primary side Ou t 24put D V C 5A DC OK A 22 dju .5- st 29 .5V The device must be installed in acc. with the regulations as in EN 60950. It must be possible to disconnect the device using a suitable isolating facility outside the power supply.
PAGE 11
TRIO-PS/3AC/24DC/5 13 Output ATTENTION: Module can become damaged + + – – – TRIO POWER Ou 24tput V DC 5A Make sure that all output lines are dimensioned according to the maximum output current or are separately protected. The cables on the secondary side must have sufficiently large cross sections in order to keep the voltage drops on the lines as low as possible. POWER + + – – – Ou tp 24 ut D V C 5A DC OK You can fasten the connection cables to the housing using cable binders.
PAGE 12
TRIO-PS/3AC/24DC/5 15 Function UOUT [V] Output characteristic curve UN IN IOUT [A] The device functions following the U/I characteristic curve. Under load, the working point follows this curve. The output current is limited in the event of a short circuit or overload. Thereby, the device does not switch off, but rather supplies a continuous output current. The secondary voltage is reduced until the short circuit or overload on the secondary side has been remedied.
PAGE 13
TRIO-PS/3AC/24DC/5 Redundant operation IN IN + − + − + − Σ = IN + − Redundant circuits are suitable for the supply of systems which make especially high requirements on the operational safety. If a fault occurs in the primary circuit of the first power supply unit, the second device automatically takes over the entire power supply, without interruption, and vice versa.